en: climate-change discharge hydrology snowmelt precipitation soil-moisture

en: Daily simulated data for the reference period

en: Daily simulated discharge, precipitation, snowmelt, and soil moisture for the reference period 1981-2017 in mm.

en: Daily simulated data for the future period

en: Daily simulated discharge, precipitation, snowmelt, and soil moisture for the period 1981-2100 in mm for the 307 catchments.

en: Shapefile of 307 catchments in Switzerland

en: Shapefile of the 307 medium-sized catchments in Switzerland. The "gridcode" provides the ID of the catchment used in the datafiles.

en:
Daily discharge and the related hydro-meteorological variables precipitation, snowmelt, and soil moisture are provided for current (1981-2017) and for future climate conditions (1981-2100) for 307 medium-sized catchments in Switzerland. The catchments have a median catchment area of 117 km². The 307 catchments together form a set representative of the climatological conditions and runoff characteristics in Switzerland. The four variables were simulated at a daily resolution using the hydrological model PREVAH. PREVAH is a conceptual process-based model that was run in this study in its fully distributed version on a 500 m grid (Viviroli et al. 2009a). For the calibration, runoff time series from 140 mesoscale catchments covering the different runoff regimes were used. The model calibration was conducted over the period 1993-1997. Verification was performed on the period 1983-2005 using (i) volumetric deviation (Viviroli et al. 2007) and (ii) benchmark efficiency (Schäfli et al 2007) as objective functions. The calibration and validation procedures are described in detail in Köplin et al. (2010). The parameters for each model grid cell were derived by regionalizing the parameters obtained for the 140 catchments with a procedure based on ordinary kriging (Viviroli et al. 2009b, Köplin et al. 2010).
The calibrated and validated model was then driven with transient meteorological data (precipitation, temperature, radiation, and wind) representing both reference (1981-2017) and future climate conditions (2018-2099). The data were derived from the CH2018 climate scenarios (NCCS 2018) provided by the Swiss National Centre for Climate Services (NCCS). They were obtained from climate experiments produced with different climate modeling chains, consisting of a global and a regional circulation model each, within EUROCORDEX for three representative concentration pathways (RCP) emission scenarios. Downscaled output of ten climate model chains derived by quantile mapping were considered. The focus was on the chains of the EUR-11 domain with a horizontal resolution of 0.11 degrees (roughly 12.5 km). The climate model chains (GCM, RCM, RCP, and grid resolution) used are listed below:

- ICHEC-EC-EARTH	DMI-HIRHAM5	2.6	EUR-11
- ICHEC-EC-EARTH	DMI-HIRHAM5	4.5	EUR-11
- ICHEC-EC-EARTH	DMI-HIRHAM5	8.5	EUR-11
- ICHEC-EC-EARTH	SMHI-RCA4	2.6	EUR-11
- ICHEC-EC-EARTH	SMHI-RCA4	4.5	EUR-11
- ICHEC-EC-EARTH	SMHI-RCA4	8.5	EUR-11
- MOHC-HadGEM2-ES	SMHI-RCA4	4.5	EUR-11
- MOHC-HadGEM2-ES	SMHI-RCA4	8.5	EUR-11
- MPI-M-MPI-ESM-LR	SMHI-RCA4	4.5	EUR-11
- MPI-M-MPI-ESM-LR	SMHI-RCA4	8.5	EUR-11

*References*:

-	Köplin, N., D. Viviroli, B. Schädler, and R. Weingartner (2010), _How does climate change affect mesoscale catchments in Switzerland? - A framework for a comprehensive assessment_, Advances in Geosciences, 27, 111-119, doi:10.5194/adgeo-27-111-2010.
-	National Centre for Climate Services (2018), CH2018 - _Climate Scenarios for Switzerland_, Tech. rep., NCCS, Zurich.
-	Schäfli, B., and H. V. Gupta (2007), _Do Nash values have value?_, Hydrological Processes, 21, 2075-2080, doi:10.1002/hyp.6825.
-	Viviroli, D., J. Gurtz, and M. Zappa (2007), _The hydrological modelling system PREVAH. Part II - Physical model description_, Geographica Bernensia, 40, 1-89.
-	Viviroli, D., M. Zappa, J. Gurtz, and R. Weingartner (2009a), _An introduction to the hydrological modelling system PREVAH and its pre- and post-processing-tools_, Environmental Modelling & Software, 24, 1209-1222, doi:10.1016/j.envsoft.2009.04.001.
-	Viviroli, D., H. Mittelbach, J. Gurtz, and R. Weingartner (2009b), _Continuous simulation for flood estimation in ungauged mesoscale catchments of Switzerland-Part II: Parameter regionalisation and flood estimation results_, Journal of Hydrology, 377 (1), 208-225, doi:10.1016/j.jhydrol.2009.08.022.

climate-change

display_name: climate-change

discharge

display_name: discharge

hydrology

display_name: hydrology

precipitation

display_name: precipitation

snowmelt

display_name: snowmelt

soil-moisture

display_name: soil-moisture

en: Simulated future discharge and climatological variables for medium-sized catchments in Switzerland


mountain-permafrost-hydrology

maintainer: Jeannette Noetzli

title_for_slug: mountain-permafrost-hydrology

en: climate-change-impacts monitoring-techniques ice-rich-permafrost permafrost-degradation mountain-permafrost-hydrology mass-movements

state: active

type: dataset

en: Synthesis report chapter of the Hydro-CH2018 project of the Federal Office for the Environment (FOEN)

media_type: application/pdf

format: PDF

en: DORA Persistent URL

en: This report was prepared as one of the synthesis report chapters of the Hydro-CH2018 project of the Federal Office for the Environment (FOEN). In earlier reports such as the CH2014-IMPACTS report (CH-Impacts 2014), the topic of mountain permafrost hydrology was not addressed. Here, we provide a baseline of the available knowledge of mountain permafrost in the Swiss Alps for future reference. We compile an overview of the current understanding of mountain permafrost in the Swiss Alps, its distribution and characteristics, observed and projected changes, and expected impacts on slope stability, infrastructure and hydrological aspects. We also briefly describe the measurement techniques and modelling approaches applied. The chapter closes with a summary of the most important open research questions. The literature cited mainly includes studies on mountain permafrost published in scientific journals and assessments of long-term observation data. We focus on permafrost hydrology interactions wherever information is available. However, systematic studies on permafrost hydrology in mountain areas are still limited.

climate-change-impacts

display_name: climate-change-impacts

ice-rich-permafrost

display_name: ice-rich-permafrost

mass-movements

display_name: mass-movements

monitoring-techniques

display_name: monitoring-techniques

mountain-permafrost-hydrology

display_name: mountain-permafrost-hydrology

permafrost-degradation

display_name: permafrost-degradation

educ

fr: Éducation, culture et sport

de: Bildung, Kultur und Sport

en: Education, culture and sport

it: Istruzione, cultura e sport

envidat

fr: EnviDat: le portail de données environnementales

de: EnviDat: das Umwelt-Datenportal

en: EnviDat: the Environmental Data Portal

it: EnviDat: il portale dei dati ambientali

fr: EnviDat est le portail de données du WSL; il offre un accès uniformisé et réglementé aux données de surveillance et de recherche en matière d’environnement. Ce portail est capable d’héberger et de publier des ensembles de données précieuses et uniques, qui sont partagées aux quatre coins de la planète. Ce faisant, EnviDat favorise la recherche et contribue à l’avancement des sciences environnementales.

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

de: EnviDat ist das Datenportal der WSL für einen einheitlichen und verwalteten Zugang zu Umweltdaten aus Monitoring- und Forschungsprojekten. Auf dem Portal können Datensätze gehostet und veröffentlicht werden. Durch die weltweite Bereitstellung einzigartiger und wertvoller Datensätze leistet EnviDat einen Beitrag zur Forschung im Bereich der Umweltwissenschaften.

it: EnviDat è il portale dati del WSL che fornisce un accesso unificato e gestito ai dati di monitoraggio ambientale e di ricerca. Il portale ha la capacità di ospitare e pubblicare serie di dati preziosi e unici che vengono condivisi in tutto il mondo. Così facendo, EnviDat promuove la ricerca e contribuisce al progresso della scienza ambientale.

political_level: other

wsl

capacity: public

type: organization

approval_status: approved

key: guid

key: uri

value: Envidat Harvester

en: Mountain Permafrost Hydrology


maintainer: Amelie Fees

en: time-lapse-photography glide-snow-avalanche snowpack-simulation avalanche avalanche-activity

en: README

en: README.txt explaining the dataset and columns of tables in more detail.

format: SERVICE

en: SNOWPACK simulations

en: SNOWPACK simulations (.pro and .smet) covering season 2008/09 to 2021/22 at 10 virtual locations on Dorfberg. The locations correspond to the most common glide-snow avalanche paths.

en: Glide distances for opening glide-cracks

en: This folder contains all glide-cracks where glide-distances were extracted from time-lapse photographs. Glide-distances were calculated in x-direction (width) and y-direction (downslope, length) by georeferencing the images.

en: Glide-snow avalanche activity

en: Table that contains all glide-snow avalanche events that were detected in time-lapse photographs (season 2008/09 to 2021/22). The columns are explained in the README.txt

en:
This dataset includes the processed data of the glide-snow avalanche activity and dynamics on Dorfberg (Davos, Switzerland) covering seasons 2008/09 to 2021/22. This dataset was described in the research article:

Fees, A., van Herwijnen A., Altenbach, M., Lombardo, M., Schweizer, J.: Glide-snow avalanche characteristics at different time-scales extracted from time-lapse photography, Annals of Glaciology, 91

We extracted the dynamics of opening glide-cracks and the glide-snow avalanche activity from time-lapse photographs. Glide-snow avalanches were separated into surface and interface events using the liquid water content which was simulated with SNOWPACK at 10 virtual stations on Dorfberg.

avalanche

display_name: avalanche

avalanche-activity

display_name: avalanche-activity

glide-snow-avalanche

display_name: glide-snow-avalanche

snowpack-simulation

display_name: snowpack-simulation

time-lapse-photography

display_name: time-lapse-photography

en: Glide-snow avalanche activity on Dorfberg, Davos, Switzerland


biogas-aus-hofdunger-in-der-schweiz

maintainer: EnviDat Support

title_for_slug: biogas-aus-hofdunger-in-der-schweiz

en: switzerland bioenergy manure biogas review

en: Biogas aus Hofdünger in der Schweiz

en: Ziel dieses Whitepapers ist es, Entscheidungsträgern, Verwaltungen und Stakeholdern die aktuellsten Forschungsergebnisse zur Verfügung zu stellen, um die optimale Nutzung von Bioenergie aus Hofdünger in der Schweizer Energiewende zu fördern. Zu diesem Zweck werden die Ergebnisse des Schweizer Kompetenzzentrums für Bioenergieforschung - SCCER BIOSWEET - zusammengefasst und in einem breiteren Kontext dargestellt. Wenn nichts anderes erwähnt wird, beziehen sich die Ergebnisse auf die Schweiz und im Falle der Ressourcen auf die heimischen Biomassepotenziale.

bioenergy

display_name: bioenergy

biogas

display_name: biogas

manure

display_name: manure

review

display_name: review

switzerland

display_name: switzerland


en: complex-terrain numerical-simulation meteoswiss cosmo-wrf high-resolution

en: MeteorologicalData

media_type: application/zip

en: Scripts to process meteorological data (see Section 2 in COSMOWRFdocumentation.pdf).

format: ZIP

mimetype: application/zip

en: StaticData

en:
Scripts to process geographical/static data (see Section 3 in COSMOWRFdocumentation.pdf).
- ascii_to_bin_landuse.f90
- ascii_to_bin_soiltype.f90
- ascii_to_bin_topo_wgs84_ws2sf1.f90
- see_slopes.ncl
- soiltype_writing.py
- toposmooth_wgs84_cosmobound.ncl
- write_geogrid.o

en: WRFrun

en: Scripts to run COSMO-WRF simulation (see Section 6 in COSMOWRFdocumentation.pdf)

en: COSMO-WRF documentation v1.0

en:
Gerber, Franziska; Sharma, Varun (2018). Running COSMO-WRF on very-high resolution over complex terrain. EnviDat. doi:10.16904/envidat.35

Documentation about the procedure to run COSMO-WRF

mimetype: application/pdf

en: WPSSetup

en: Scripts that need to be changed to compile WPS (see COSMOWRFdocumentation.pdf, Section 4)

en: WPSrun

en: Scripts to run the WRF pre-processing (WPS) for COSMO-WRF simulation (see Section 5 in COSMOWRFdocumentation.pdf)

en: Postprocessing

en: Postprocessing scripts to map WRF output on swiss coordinates (see Section 7 in COSMOWRFdocumentation.pdf)

en: This is a technical documentation of the procedure to run the Weather Research and Forecasting (WRF) model over complex alpine terrain using Consortium for Small-Scale Modeling (COSMO) reanalysis by the Federal Office of Meteorology and Climatology (MeteoSwiss) as initial and boundary conditions (COMSO-WRF). The setup is adapted for very high resolution simulations based on COSMO-2 (2.2 km resolution) reanalysis. This document gives an overview over steps to setup COSMO-WRF and adaptations needed to run COSMO-WRF. Additionally, the calculation of precipitation rate at a horizontal plane and remapping COSMO-WRF output on Swiss coordinates are documented.

complex-terrain

display_name: complex-terrain

cosmo-wrf

display_name: cosmo-wrf

high-resolution

display_name: high-resolution

meteoswiss

display_name: meteoswiss

numerical-simulation

display_name: numerical-simulation

educ

en: Education, culture and sport

envidat

en: EnviDat: the Environmental Data Portal


en: snow-hydrology rain-on-snow catchment-data meteorological-data snowpack

en: The file contains all data needed to run simulations with the snow cover model SNOWPACK.

media_type: text/plain

format: TXT

mimetype: text/plain

en: Meteorological data used to run SNOWPACK for 58 catchments in the Swiss Alps. The data consists of a 2 km grid of "virtual meteorological stations" for each catchment. It was used to simulate snow cover processes during rain-on-snow events, therefore meteorological data of each catchment contains at least one rain-on-snow event. Further information can be found in the attached readme.txt and in Würzer & Jonas et al. (2017), currently under review in Hydrological Processes.

catchment-data

display_name: catchment-data

meteorological-data

display_name: meteorological-data

rain-on-snow

display_name: rain-on-snow

snow-hydrology

display_name: snow-hydrology

snowpack

display_name: snowpack

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: Meteorological data for investigation of rain-on-snow events in 58 catchments in Switzerland


maintainer: EnviDat

en: research-data-management nead metadata-convention csv meteorological-data-format

en: MeteoIO (future reference implementation)

media_type: text/html

format: HTML

mimetype: text/html

en: NEAD on GitHub

en: PyNEAD (future reference implementation)

en: NEAD syntax v0.1 (EBNF)

en:
Acknowledgement: The NEAD format includes NetCDF metadata and is proudly inspired by both SMET and NetCDF formats. NEAD is designed as a long-term data preservation and exchange format.

The NEAD specifications were presented at the "WMO Data Conference 2020 - Earth System Data Exchange in the 21st Century" (Virtual Conference).

-----------------------

Summary:
The Non-Binary Environmental Data Archive (NEAD) format is being developed as a generic and intuitive format that combines the self-documenting features of NetCDF with human readable and writeable features of CSV. It is designed for exchange and preservation of time series data in environmental data repositories.

License: The NEAD specifications are released to the public domain under a Creative Commons CC0 "No Rights Reserved" international license. You can reuse the information contained herein in any way you want, for any purposes and without restrictions.

csv

display_name: csv

metadata-convention

display_name: metadata-convention

meteorological-data-format

display_name: meteorological-data-format

nead

display_name: nead

research-data-management

display_name: research-data-management

en: Non-Binary Environmental Archive Data (NEAD) format


maintainer: Esther Frei

en: stillberg long-term-experiment treeline afforestation mountain-forest

mimetype: application/x-zip-compressed

en:
 Background information

The Stillberg ecological treeline research site in the Swiss Alps was established in 1975, with the aim to develop ecologically, technically, and economically sustainable reforestation techniques at the treeline to reduce the risk of snow avalanches. In the course of time, additional research aspects gained importance, such as the ecology of the treeline ecotone under global change. Long-term monitoring of the large-scale high-elevation afforestation has generated data about tree growth, survival, and vitality. In addition, detailed characteristics of the microsite conditions of the research were conducted. Besides providing a scientific basis and practical guidelines for high-elevation afforestation, this research has contributed to a comprehensive understanding of ecological processes in the treeline ecotone.

 Experiment description

The Stillberg afforestation experiment was established in 1975 by planting 92,000 seedlings of *Larix decidua*, *Pinus cembra* and *Pinus mugo* ssp. *uncinata* in the alpine treeline ecotone. The afforestation site is located on a northeast-facing slope with steep, topographically highly structured terrain and covers elevations from 2075 to 2230 m a.s.l. The afforestation site was divided into 4052 square plots of 3.5 × 3.5 m, arranged in a regular species-alternating pattern over the whole area. Each plot contained 25 trees of one species (1350 plots per species), and the seedlings were systematically planted 70 cm apart. The trees have been monitored since 1975. Specifically, tree mortality was assessed annually from 1975 until 1995 and has been documented every ten years since then, with surveys in 2005 and 2015 (the next survey is due in 2025). Height of the surviving trees was measured in 1975, 1979, 1982, 1985, 1990, 1995, 2005, and 2015. In 1995, 2005, and 2015, drivers of tree vitality were assessed for a subset of trees per plot. Additionally, an extensive set of environmental parameters characterizing microsite conditions of the afforestation area were recorded before and after the planting of the trees.

 Data description

The five datasets from the afforestation experiment comprise ecological and environmental data from the main afforestation experiment in five datasets with accompanying metadata (Stillberg_afforestation_all_metadata.xlsx). All data and metadata files are bundled in a ZIP-file (Stillberg_afforestation_v1.zip). In particular, a first dataset contains environmental data characterising microsite conditions of the 4000 plots with regard to soil, topography, vegetation and microclimatic conditions (Stillberg_afforestation_plot_data_v1.csv; Stillberg_afforestation_plot_metadata_v1.csv. In each plot, the natural tree regeneration was assessed by counting seedings of several tree species in 2005 and 2015 (Stillberg_afforestation_regeneration_data_v1.csv; Stillberg_afforestation_regeneration_metadata_v1.csv). Furthermore, specific information about each of the 92’000 planted trees of the tree species is available (Stillberg_afforestation_tree_parameter_data_v1.csv; Stillberg_afforestation_tree_parameter_metadata_v1.csv). Survival data for each of the 92’000 individual trees can be found in a separate dataset (Stillberg_afforestation_tree_survival_data_v1.csv; Stillberg_afforestation_tree_survival_metadata_v1.csv). Tree growth and vitality parameters are available for all trees from 1995, and for subsets of trees for 2005 and 2015 (Stillberg_afforestation_tree_measurements_data_v1.csv; Stillberg_afforestation_tree_measurements_metadata_v1.csv).

afforestation

display_name: afforestation

long-term-experiment

display_name: long-term-experiment

mountain-forest

display_name: mountain-forest

stillberg

display_name: stillberg

treeline

display_name: treeline

en: Long-term afforestation experiment at the Alpine treeline site Stillberg, Switzerland


maintainer: Elisabeth Hafner

en: reliability avalanche avalanche-mapping avalanche-size-estimation remote-sensing

en: AvalancheReliabilityData

en: The .zip contains all data used to conduct the reliability study as well as the results, a detailed description of the included files is contained in the included pdf. All geospatial data is provided in the Swiss Coordinate System: CH1903+ / LV95 (EPSG 2056). For any use of the data the proper citation provided is obligatory!

en:
This dataset contains the data used and collected to investigate the reliability of avalanche size estimates and avalanche outlines (see related publications). Namely this is

 Avalanche size estimates

* the 10 pictures depicting avalanches
* the survey results from the 170 participants

 Avalanche outlines mapped from oblique photographs
* the pictures of the six avalanches
* the avalanche outlines mapped by the 10 participants
* the reference mapped from the georeferenced photographs

 Avalanche outlines from remotely-sensed imagery
* the orthophotos in the four different resolutions (2m, 1m, 50cm, 25cm)
* the area of interest (AoI) delimiting the research area
* the avalanche mappings in each resolution for all five participants
* the shade masks used to separate illuminated and shaded areas

The acquisition of the orthophotos has been partially supported by the Swiss National Science Foundation (SNF; Grant N°200021_172800).

avalanche

display_name: avalanche

avalanche-mapping

display_name: avalanche-mapping

avalanche-size-estimation

display_name: avalanche-size-estimation

reliability

display_name: reliability

remote-sensing

display_name: remote-sensing

educ

en: Education, culture and sport

en: Data reliability study: avalanche size estimates and outlines


en: climate-change temperature swiss-forest-lab relative-humidity wind-speed par meteo precipitation meteorology long-term

en: Data plot of the forest station (VOB)

en: Data overview for air temperature, relative humidity, precipitation, PAR, wind speed.

en: Site photo of the forest station (VOB)

en: Site photo of the forest station from the side.

mimetype: image/jpeg

en: Site photo of the field station (VOF)

en: Site photo of the field stationfrom the side.

en: Forest station data (VOB)

media_type: text/csv

en: Data file.

format: CSV

mimetype: text/csv

en: Site aerial photo (Vordemwald)

en: Site aerial photo from both Vordemwald stations. Source: Google. 2016. Site aerial photo from both Vordemwald stations. Retrieved November 11, 2016, from https://www.google.ch/maps

en: Data plot of the field station (VOF)

en: Field station data (VOF)

en: High quality meteorological data are needed for long-term forest ecosystem research, particularly in the light of global change. The long-term data series published here comprises almost 20 years of measurements for two meteorological stations in Vordemwald in Switzerland where one station is located within a natural mixed forest stand (VOB) with European silver fir (_Abies alba_; 110 yrs) and oak trees (_Quercus sp._; 190-210 yrs) as dominant tree species. A second station is situated in the very vicinity outside of the forest (field station, VOF). The meteorological time series are presented in hourly time resolution of air temperature, relative humidity, precipitation, photosynthetically active radiation (PAR) and wind speed. Vordemwald is part of the Long-term Forest Ecosystem Research Programme (LWF) established and maintained by the Swiss Federal Research Institute WSL.

climate-change

display_name: climate-change

long-term

display_name: long-term

meteo

display_name: meteo

meteorology

display_name: meteorology

par

display_name: par

precipitation

display_name: precipitation

relative-humidity

display_name: relative-humidity

swiss-forest-lab

display_name: swiss-forest-lab

temperature

display_name: temperature

wind-speed

display_name: wind-speed

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: Vordemwald, Switzerland: Long-term forest meteorological data from the Long-term Forest Ecosystem Research Programme (LWF), from 1996 onwards


en: snow-avalanche acoustic-emissions snow viscous-deformation snow-mechanics sintering fiber-bundle-model snow-failure

en: fiber-bundle-model-for-snow-failure

en: Data underlying Figures in publication "Modelling Snow Failure Behavior and Concurrent Acoustic Emissions Signatures with a Fiber Bundle Model" submitted to "Geophysical Research Letters"

en:
This dataset contains modeled and experimental results for laboratory snow failure experiments and the concurrent acoustic emissions signatures for different loading rates. For modelling the snow failure we used a fiber bundle model that includes sintering and viscous deformation.

The data underlay the figures in the publication "Modelling Snow Failure Behavior and Concurrent Acoustic Emissions Signatures with a Fiber Bundle Model" submitted for publication to "Geophysical Research Letters".

acoustic-emissions

display_name: acoustic-emissions

fiber-bundle-model

display_name: fiber-bundle-model

sintering

display_name: sintering

snow

display_name: snow

snow-avalanche

display_name: snow-avalanche

snow-failure

display_name: snow-failure

snow-mechanics

display_name: snow-mechanics

viscous-deformation

display_name: viscous-deformation

educ

en: Education, culture and sport

en: Fiber Bundle Model for snow failure and concurrent Acoustic Emissions


data-broedlin-cnp

title_for_slug: data-broedlin-cnp

en: carbon forest drying-rewetting nitrogen mineralization stoichiometry phosphorus dissolved-organic-matter soil

en: Data Broedlin-CNP-Release

en: Raw data of C-N-P mobilization experiment from Oi, Oe/Oa, and A horizons of beech forest soils along a nutrient availability gradient.

format: XLS

en: Data Broedlin-CNP

en: Mircocosm experiment to identify the individual patterns and controls of C, N, and P mobilization in soils under beech forests. Organic and mineral horizons sampled along a nutrient availability gradient in Germany were exposed to either permanent moist conditions or to dry spells in microcosms and quantified the release of inorganic and organic C, N, and P.

carbon

display_name: carbon

dissolved-organic-matter

display_name: dissolved-organic-matter

drying-rewetting

display_name: drying-rewetting

forest

display_name: forest

mineralization

display_name: mineralization

nitrogen

display_name: nitrogen

phosphorus

display_name: phosphorus

soil

display_name: soil

stoichiometry

display_name: stoichiometry

en: Data Broedlin CNP


maintainer: Anita C Risch

en: soil-properties climate herbivore-exclusion nutrient-addition microbial-biomass-carbon microbial-respiration anthropogenic-management

en: Risch et al. GEB_data.xlsx

en:
Study sites and experimental design
We collected data from 23 sites that are part of the Nutrient Network Global Research Cooperative (NutNet, https://nutnet.umn.edu/). The mean annual air temperature (MAT) across these sites ranged from -4 to 22°C, mean annual precipitation (MAP) from 252 to 1592 mm, and elevations from 6 to 4261 m above sea level (Fig 1a, Supplementary Table S1), hence cover a wide range of climatic conditions under which grasslands occur (Fig 1b). Soil organic C concentrations ranged between 0.8 to 7.8%, soil total N concentrations between 0.1 and 0.6%, and the soil C:N ratio between 9.1 and 21.5. Soil clay content spanned from 3.0 to 35%, and soil pH from 3.4 to 7.6 (Supplementary Table S2).
At each site, the effects of nutrient addition and herbivore exclusion were tested via a randomized-block design (Borer et al., 2014). Three blocks with 10 treatment plots each were established at each site, except for the site at bldr.us (only two blocks). Each of these 10 plots was randomly assigned to a nutrient or fencing treatment. An individual plot was 5 x 5 m, divided into four 2.5 x 2.5 m subplots. Each subplot was further divided into four 1 x 1 m square sampling plots, one of which was set aside for soil sampling (Borer et al., 2014). Plots were separated by at least 1 m wide walkways. We collected soil samples from four different treatments for this study: (i) untreated control plots (Control), (ii) herbivore exclusion plots (Fence), (iii) plots fertilized with N, P, K, plus nine essential macro and micronutrients (NPK), and (iv) plots with simultaneous fertilizer addition and herbivore exclusion (NPK+Fence). The experiments were established at different times in the past, with years of treatment different among sites (2 – 9 years since start of treatment; Supplementary Table S1). For the nutrient additions, all sites applied 10 g N m-2 each year as time-release urea; 10 g P m-2 yr-1 as triple-super phosphate; 10 g K m-2 yr-1 as potassium sulfate. A micro-nutrient mix (Fe, S, Mg, Mn, Cu, Zn, B, Mo, Ca) was applied at 100 g m-2 together with K in the first year of treatments but not thereafter.
We excluded large vertebrate herbivores (Fence) by fencing two plots, one with and one without NPK additions, within each block. The fences excluded all aboveground mammalian herbivores with a body mass of over 50 g (Borer et al., 2014). At most sites, the fences were 180 cm high, and the fence contained a wire mesh (1 cm holes) for the bottom 90 cm with a 30 cm outward-facing flange stapled to the ground to exclude burrowing animals. Climbing and subterranean animals may potentially still access these plots (Borer et al., 2014). For slight modifications in fence design at a few sites see Supplementary Table S3. Most sites only had wild herbivores, although four sites were also grazed by domestic animals (Supplementary Table S1).

Collection of soil samples, soil microbial respiration, microbial biomass, and other soil properties
Each of the 23 sites received a package containing identical material from the Swiss Federal Institute for Forest, Snow and Landscape Research WSL, Switzerland to be used for sampling (Risch et al., 2015; Risch et al., 2019). We collected two soil cores of 5 cm diameter and 12 cm depth in each sampling plot and composited them to measure MR, MBC, and soil chemical properties (see below). An additional sample (5 x 12 cm) was collected to assess soil physical properties. This sample remained within a steel sampling core after collection and both ends were tightly closed with plastic caps to avoid disturbance. All soils were shipped cooled to the laboratory at (Location will be disclosed after manuscript acceptance) within a few days after collection. Soils were sampled roughly 6 weeks prior to peak biomass at each site during 2015 and 2016.
To assess MR (CO2 production) in a laboratory incubation experiment we weighed duplicate soil samples (8 g dry soil equivalent) into 50-ml Falcon tubes. No additional substrate (glucose, sugar) was added to these samples. We adjusted the soil moisture of each sample to 60% field capacity. We then placed a 15 ml plastic test tube (Semadeni 1701A) containing 7.25 ml 0.05 M NaOH over each soil sample. The test tube was fixed with a plastic rod so that it was not in contact with the soil sample. The Falcon tubes were then sealed with a screw cap and placed in an incubator under completely dark conditions at 20°C. The CO2 produced by microbial respiration was absorbed by the 0.05 M NaOH. For five weeks we measured the decrease in conductivity within the 0.05 M NaOH solution on a weekly basis with a Multimeter WTW Multi 3410 (WTW GmbH, Germany) and replaced the 0.05 M NaOH with fresh solution. We included Falcon tubes without soil samples in each incubation run as blanks to test if tubes were tight and no CO2 could enter or escape. We calibrated the relationship between conductivity reduction and NaOH absorbed as follows: 400 ml 0.05 M NaOH was placed in a beaker and its conductivity was measured with the multimeter. While stirring, air containing CO2 was blown into the solution for approximately one minute, which reacts with NaOH to form Na2CO3. After this process, conductivity was measured again. We then transferred 7.25 ml of the solution into a smaller beaker and added 1 ml of 0.1 M BaCl2 to precipitate Na2CO3 and then titrated the solution with 0.05 M HCl to determine the remaining NaOH. We then repeated these steps with the remaining solution a total of nine times and plotted the conductivities (y-axis) against the NaOH consumed (x-axis, Supplementary Fig S1). This regression line was used to infer the consumption of NaOH from the conductivity reduction in the incubation experiments and to calculate CO2 evolution during incubation. In addition, we determined the optimum concentration for the NaOH solution in series of preliminary experiments, so that the concentration was not too high to become insensitive, but also not too low so that not all NaOH reacts during incubation. We then calculated MR (mg CO2-C kg dry soil-1 h-1) as total amount of CO2 released over the 5 weeks divided by the duration of the entire incubation in hrs.
Soil microbial biomass carbon (MBC; mg C kg soil-1 ) was measured at the beginning of the experiment by measuring the maximal respiratory response to the addition of glucose solution (4 mg glucose per g soil dry weight dissolved in distilled water; substrate-induced respiration method) on approximately 5.5 g of soil (J. P. E. Anderson & Domsch, 1978; Nico Eisenhauer et al., 2018; Scheu, 1992). For this purpose we used an O2-micro-compensation apparatus (Scheu, 1992). More specifically, substrate-induced respiration was calculated from the respiratory response to D-glucose for 10 hr at 20°C. Glucose was added according to preliminary studies to saturate the catabolic enzymes of microorganisms (4 mg g soil-1 dissolved in 400 ml deionized water). The mean of the lowest three readings within the first 10 hrs (between the initial peak caused by disturbing the soil and the peak caused by microbial growth) was taken as maximum initial respiratory response (MIRR; ml O2 kg soil-1 h-1) and microbial biomass (mg C kg soil-1) was calculated as 38 x MIRR (Beck et al., 1997; Cesarz et al., 2022; Thakur et al., 2015).
The rest of the composited sample was dried at 65°C for 48 h, ground and sieved (2 mm mesh) to assess the soil pH, mineral soil total C and N and C:N ratio, and mineral soil organic C (Risch et al., 2019). The undisturbed sample was used to assess water holding capacity (WHC), bulk density (BD), and soil texture [sand, silt, clay; methods in (Risch et al., 2019)]. We used the percentage of sand and clay as an indicator of soil texture in this study. MAT (°C), MAP (mm) and temperature of the wettest quarter (°C) were obtained from www.worldclim.com (Fick & Hijmans, 2017; Hijmans, Cameron, Parra, Jones, & Jarvis, 2005). These variables were selected as they were found to be drivers of soil nutrient processes across these sites in earlier studies (Risch et al., 2020; Risch et al., 2019). Mean annual soil temperatures (MAST; °C) for the 0 to 5 cm soil layer were obtained for each site from the SoilTemp maps (J. Lembrechts et al., 2021; J. J. Lembrechts et al., 2022), global gridded modelled products of soil bioclimatic variables for the 1979-2013 period at a 1-km² resolution, based on CHELSA, ERA5 and in-situ soil temperature measurements.
Numerical calculations and statistical analyses
We calculated MMQ as MR/MBC. We corrected this measure using the average soil temperature of each site (MMQsoil). This temperature correction is necessary as incubation temperatures are usually much higher than site mean annual soil temperatures (see Xu et al. 2017). MMQsoil = MMQ x Q10(MAST – 20)/10, where Q10 was assumed to be 2 (Xu et al. 2017). See Supplementary Fig S2 for comparison of air and soil temperatures across the 23 sites as well as the incubation temperature.
Some of the explanatory variables (clay, soil organic C, C:N ratio) were skewed and were thus log-transformed prior to analyses. All continuous explanatory variables were centred and scaled to have a mean of zero and variance of one. To avoid collinearity between them we filtered them using correlation analysis (Supplementary Fig S3). From the variables that were strongly correlated (Pearson’s |r| > 0.70) (Dormann et al., 2013), we selected the ones that allowed us to minimize the number of variables (Supplementary Fig S3). Specifically, soil total N concentration, soil total C concentration, soil sand content and soil bulk density were dropped from the dataset. We then assessed how these edaphoclimatic variables are related to MMQ across our global grasslands.
For this, we used linear mixed effects models (LMMs) fitted by maximum likelihood with the lme function in the nlme package (version 3.1-153) (Pinheiro, Bates, DebRoy, & Sarkar, 2021) in R version 3.6.3. (R Core Team, 2019). We used treatment as a fixed effect and plot nested in site as random effects to assess treatment differences in MMQsoil, as well as MR, and MBC. The number of years since the treatment started was included as a fixed effect in all the initial models but was not significant and therefore not retained in the models. To assess how differences in MMQsoil were affected by environmental factors (soil, climatic properties) we again used LMMs. Soil and climatic properties were included as fixed effects and plot nested in site as random effects. We did not include interactions between environmental variables. We then used the MuMin package (Barton, 2018) (version 1.42.1) to select the best models that explained the most variation based on Akaike’s information criterion (AIC; model.avg function). We used the corrected AIC (AICc) to account for our small sample size and selected the top models that fell within 4 AICc units (delta AICc < 4) (Burnham & Anderson, 2002; Johnson & Omland, 2004). We present all our top models rather than model averages. Conditional averages are provided in the Supplementary material.
Based on findings from analyses described above and the literature, we developed a conceptual model of direct and indirect relationships between both edaphoclimatic variables and experimental treatments (Supplement Figure S4) to obtain a more holistic approach in understanding how these properties affect MMQsoil. We had data from 23 sites with 272 observations. We tested this model using structural equation modelling based on a d-sep approach (Lefcheck, 2016; Shipley, 2009). We considered those environmental drivers that were included in our top LMMs, namely temperature of the wettest quarter (T.q.wet), soil pH, water holding capacity (WHC) and soil organic C (organic C; Supplementary Figure S4). These factors were allowed to directly affect MMQsoil, and via their interactions with treatments. In addition, treatments were allowed to directly affect MMQsoil. Treatments were included as dummy variables in the model. We tested our conceptual model (Supplementary Fig S4) using the piecewiseSEM package (version 2.0.2; Lefcheck, 2016) in R 3.4.0, in which a structured set of linear models are fitted individually. This approach allowed us to account for the nested experimental design, and overcome some of the limitations of standard structural equation models, such as small sample sizes (Lefcheck, 2016; Shipley, 2009). We used the lme function of the nlme package to model response variables, including site as a random factor. Good fit of the SEM was assumed when Fisher’s C values were non-significant (p > 0.05). For all significant interactions between soil or climate variables and treatments detected in the SEMs, we calculated treatment effect sizes, i.e., the differences in MMQsoil between Control and treatments as log response ratios (LRR) and plotted these values against the climate or soil factors. The LRR were defined as log(Control/Treatment), where treatment was either Fence, NPK or NPK+Fence. To assess which of the LRR-climate or soil property relationships were significant we again used LMMs, in which soil and climatic properties were included as fixed effects and plot nested in site as random effects.

en:
This dataset contains all data on which the following publication below is based.

Paper Citation:

Risch Anita C., Zimmermann, Stefan, Schütz, Martin, Borer, Elizabeth T., Broadbent, Arthur A.D., Caldeira, Maria C., Davies, Kendi F., Eisenhauer, Nico, Eskelinen, Anu, Fay, Philip A., Hagedorn, Frank, Knops, Johannes M.H., Lembrechts, Jonas, J., MacDougall, Andrew S., McCulley, Rebecca L., Melbourne, Brett A., Moore, Joslin L., Power, Sally A., Seabloom, Eric W., Silveira, Maria L., Virtanen, Risto, Yahdjian, Laura, Ochoa-Hueso, Raul (accepted). Drivers of the microbial metabolic quotient across global grasslands. Global Ecology and Biogeography

Please cite this paper together with the citation for the datafile.

The microbial metabolic quotient (MMQ; mg CO2-C mg MBC-1 h-1), defined as the amount of microbial CO2 respired (MR; mg CO2-C kg soil-1 h-1) per unit of microbial biomass C (MBC; mg C kg soil-1), is a key parameter for understanding the microbial regulation of the carbon (C) cycle, including soil C sequestration. Here, we experimentally tested hypotheses about the individual and interactive effects of multiple nutrient addition (NPK+micronutrients) and herbivore exclusion on MR, MBC, and MMQ across 23 sites (5 continents). Our sites encompassed a wide range of edaphoclimatic conditions, thus we assessed which edaphoclimatic variables affected MMQ the most and how they interacted with our treatments. Soils were collected in plots with established experimental treatments. MR was assessed in a five-week laboratory incubation without glucose addition, MBC via substrate-induced respiration. MMQ was calculated as MR/MBC and corrected for soil temperatures (MMQsoil). Using LMMs and SEMs, we analysed how edaphoclimatic characteristics and treatments interactively affected MMQsoil. MMQsoil was higher in locations with higher mean annual temperature, lower water holding capacity, and soil organic C concentration, but did not respond to our treatments across sites as neither MR nor MBC changed. We attributed this relative homeostasis to our treatments to the modulating influence of edaphoclimatic variables. For example, herbivore exclusion, regardless of fertilization, led to greater MMQsoil only at sites with lower soil organic C (<1.7%). Our results pinpoint the main variables related to MMQsoil across grasslands and emphasize the importance of the local edaphoclimatic conditions in controlling the response of the C cycle to anthropogenic stressors. By testing hypotheses about MMQsoil across global edaphoclimatic gradients, this work also helps to align the conflicting results of prior studies.

anthropogenic-management

display_name: anthropogenic-management

climate

display_name: climate

herbivore-exclusion

display_name: herbivore-exclusion

microbial-biomass-carbon

display_name: microbial-biomass-carbon

microbial-respiration

display_name: microbial-respiration

nutrient-addition

display_name: nutrient-addition

soil-properties

display_name: soil-properties


maintainer: Matthias Haeni

en: par swiss-forest-lab precipitation wind-speed relative-humidity long-term temperature meteorology meteo climate-change

en: Site photo of the field station (CIF)

en: Site photo of the field station from the side.

en: Data plot of the field station (CIF)

en: Data overview for air temperature, relative humidity, precipitation, PAR, wind speed.

en: Data plot of the forest station (CIB)

en: Site photo of the forest station (CIB)

en: Site photo of the forest station from below (viewing upwards the slope).

en: Data file.

en: Forest station data (CIB)

en: Site aerial photo (Chironico)

en: Site aerial photo from both Chironico stations. Source: Google. 2016. Site aerial photo from both Chironico stations. Retrieved November 11, 2016, from https://www.google.ch/maps

en: High quality meteorological data are needed for long-term forest ecosystem research, particularly in the light of global change. The long-term data series published here comprises almost 20 years of measurements for two meteorological stations in Chironico in Switzerland where one station is located within a natural coniferous forest stand (CIB) with Norway spruce (_Picea abies_; 160-180 yrs) and European silver fir (_Abies alba_; 140-160 yrs) as dominant tree species. A second station is situated in the very vicinity outside of the forest (field station, CIF). The meteorological time series are presented in hourly time resolution of air temperature, relative humidity, precipitation, photosynthetically active radiation (PAR) and wind speed. Chironico is part of the Long-term Forest Ecosystem Research Programme (LWF) established and maintained by the Swiss Federal Research Institute WSL.

climate-change

display_name: climate-change

long-term

display_name: long-term

meteo

display_name: meteo

meteorology

display_name: meteorology

par

display_name: par

precipitation

display_name: precipitation

relative-humidity

display_name: relative-humidity

swiss-forest-lab

display_name: swiss-forest-lab

temperature

display_name: temperature

wind-speed

display_name: wind-speed

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: Chironico, Switzerland: Long-term forest meteorological data from the Long-term Forest Ecosystem Research Programme (LWF), from 2000 onwards


maintainer: Dirk Nikolaus Karger

en: chelsa sdm climate-variablity niche-models interannual-climate-variability reptiles species-distribution-models mammals generalized-linear-models random-forests iucn range-maps amphibians generalized-additive-models

en: File containing the record dimension, genus, and species of the respective netcdf files

en: Mammals

en: Species distribution models based on different climate predictor groups

en: Reptiles

en: Readme file containing the file naming convention, file dimensions, and variable names

en: Amphibians

en: File containing the climate predictors as SAGA grid files (.sgrd)

en: We modelled the global distribution of 730 amphibian, 1276 reptile, and 1961 mammal species globally as a function of current climate at a 0.5° spatial resolution using four different predictor groups composed of different combinations of input variables: mean climatic conditions, spatial climatic variability, and temporal (interannual) climatic variability.

amphibians

display_name: amphibians

chelsa

display_name: chelsa

climate-variablity

display_name: climate-variablity

generalized-additive-models

display_name: generalized-additive-models

generalized-linear-models

display_name: generalized-linear-models

interannual-climate-variability

display_name: interannual-climate-variability

iucn

display_name: iucn

mammals

display_name: mammals

niche-models

display_name: niche-models

random-forests

display_name: random-forests

range-maps

display_name: range-maps

reptiles

display_name: reptiles

sdm

display_name: sdm

species-distribution-models

display_name: species-distribution-models

educ

en: Education, culture and sport

en: Global species distributions for mammals, reptiles, and amphibians


maintainer: Virginie Marques

en: marine dna-metabarcoding biodiversity environmental-dna fjord fish plankton

en: Code, data and figures

en: Here there are all the data and code to reproduce the figures and analysis presented in the paper, with a README.md file

en: Metabarcoding data

en: Raw metabarcoding data for both primers (teleo and 18S) and corresponding file to perform the demultiplexing and primer trimming

en:
This dataset contains the raw environmental DNA data associated with the publication *Environmental drivers of eukaryotic plankton and fish biodiversity in an Arctic fjord* in the journal Polar Biology (2023).

 Methods

**Sampling**
We sampled the Lilliehöök fjord on the west coast of Spitsbergen (Svalbard, Norway) over 3 days from 3 to 5 of August 2021. Samples were taken from the glacier front up to the fjord mouth of the Krossfjorden system, around 30 km long, after the Lilliehöök fjord merged with the mouth of Möller fjord. The fjord’s maximum depth has been recorded at 373 m (Svendsen et al. 2002) and has no sill at its entrance, thereby facilitating water exchange with the open ocean of the West Spitsbergen Current. We used a research vessel to sample 5 sites for a total of 15 samples, sampling 3 depths per site (3-m, chlorophyll a maximum and 85-m, unless sea floor was shallower). Shallow and intermediate samples between 3-m and 12-m represent ~35-L of water filtered in-situ using long tubing and a peristaltic pump, and all other deeper samples were taken from a total of 3 Niskin bottles (General Oceanics), representing 22-L of water sampled per sample. Water was filtered through a VigiDNA filtration capsule (SPYGEN) with a 0.20-µm pore size using an Athena peristaltic pump (Proactive Environmental Products, Bradenton, Florida) with a flow rate of ~1-L/min. Each sample was handled with single use tubing and gloves.

**Molecular**
To perform the amplification, we used two sets of primers: teleo (forward: ACACCGCCCGTCACTCT, reverse: CTTCCGGTACACTTACCATG; Valentini et al. 2016) and the universal eukaryotic 1389F/1510R primer pair, amplifying the V9-18S rDNA gene (Amaral-Zettler et al. 2009) (forward: TTGTACACACCGCCC, reverse: CCTTCYGCAGGTTCACCTAC).

 Data content:

+ Metabarcoding data: This zip file contains the 2 sequencing libraries filtered to only retain the samples used in the present study.
+ Code, data and figure: This zip file contains all data and code to reproduce the figures and the analysis in the study, with an associated README explaining the content of each folder.

 Additional informations
For more details, please see the Methods in the associated publication: DOI: 10.1007/s00300-023-03187-9.

biodiversity

display_name: biodiversity

dna-metabarcoding

display_name: dna-metabarcoding

environmental-dna

display_name: environmental-dna

fish

display_name: fish

fjord

display_name: fjord

marine

display_name: marine

plankton

display_name: plankton

en: Data: Environmental drivers of eukaryotic plankton and fish biodiversity in an Arctic fjord


maintainer: Zhao

en: urban-land-use land-dynamics driving-factors planning austin

en: Potential driving factors of urban transformations of Austin over 25 years

en: In this study, the Austin metropolitan area, Texas, U.S., one of the fastest urban transformations and transformations regions, is selected to test the hypothesis that spatial planning and policies are important factors of urban transformations. Despite ample previous work in understanding the interactions between human and urban form transformation at specific areas, the actual interventions and outcomes of planning and policies (e.g., ‘smart growth’) on urban forms have been poorly measured. In this study, the potential influencing factors of urban transformations of Austin over 25 years were selected and collected.

austin

display_name: austin

driving-factors

display_name: driving-factors

land-dynamics

display_name: land-dynamics

planning

display_name: planning

urban-land-use

display_name: urban-land-use

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.


en: subalpine runoff alptal first-order-catchment snow meteorological-data

en: Daily runoff data from three steep torrents in the Alptal (1968-2022)

en: Runoff, water temperature and electrical conductivity have been measured since 1968 at the outlet of three torrential catchments (with an area of approximately 1 km2 each) located in the Alptal valley: Erlenbach, Lümpenenbach and Vogelbach. This data set provides daily mean values; data at 10-min resolution can be provided on request for the period 1984-2022 (contact: alptal@wsl.ch).

en: Manual snow measurements Alptal (1968-2022)

en:
Snow depth, snow density and snow water equivalent have been measured since winter 1968/69 along more than 15 transects distributed across the Alptal valley representing different altitudes, aspects and land use (closed forest and open meadows). Length of the snow courses: 20 to 30 m. The measurement interval has been weekly to monthly.
More details about the locations and methods can be found in Stähli, M.; Gustafsson, D., (2006). Long-term investigations of the snow cover in a subalpine semi-forested catchment. Hydrological Processes, 20, 411-428. doi: 10.1002/hyp.6058.

en: Daily meteorological and snow data (1968-2022) Alptal

en:
Air temperature, dew point temperature, relative humidity, wind speed, precipitation and global radiation have been measured (since 1981) on a meadow (Erlenhöhe) in the Erlenbach catchment. It is located at 1'220 m a.s.l. with an exposure towards west. In order to assess the spatial variability of precipiation, two additional rain gauges have been running in the Vogelbach and Lümpenenbach catchment, respectively.
For the period before 1981, meteorological variables have been extrapolated from the nearby MeteoSwiss station Einsiedeln (ca. 15 km north) to the WSL station Erlenhöhe using a linear correction factor for air temperature, wind speed and precipitation.
Snow depth has been recorded automatically since 2003. Snow water equivalent has been calculated using two numerical models: COUP model (Jansson, 2012) and DeltaSnow model (Winkler et al., 2021)

Jansson, P.-E. (2012). COUP model: model use, calibration, and validation.Transactions of the ASABE, 55(4), 1335–1344.
Winkler, M., et al. (2021): Snow water equivalents exclusively from snow depths and their temporal changes: the Δsnow model, Hydrol. Earth Syst. Sci., 25, 1165-1187, 10.5194/hess-25-1165-861 2021.

en:
This data set includes 54 years of hydrometeorological measurements from small (first-order) catchments in the pre-alpine valley Alptal. Here we provide daily mean values; values in sub-daily resolution can be provided on demand.
Runoff has been measured at the outlet of three small (first-order) catchments of approximately 1 km2 area: Erlenbach (two independent runoff measurements), Vogelbach and Lümpenenbach. The catchments are similar with regard to geology (Flysch) and soil conditions (clay soils), but differ in forest coverage (20 to 60%). A detailed description of the catchments can be found at https://www.wsl.ch/alptal .
Runoff in these small catchments is typically very dynamic and can temporally carry large amounts of sediment and large wood. Thus, the accuracy of the measurements at very large flow is limited.
Meteorological variables have been measured on a meadow (Erlenhöhe) located in the Erlenbach catchment at 1220 m a.s.l. using a standard meteorological station (incl. ventilated air temperature and heated rain gauges). In addition, precipitation has also been recorded at two other locations (in the Vogelbach and Lümpenenbach catchments).
Snow measurements have been conducted weekly to monthly since 1968 at more than 15 locations (30-m transects) representing different altitudes, aspects and land uses (meadow, forest). In addition, snow depth has been recorded continuously since 2003 at Erlenhöhe, and for this location we also include a simulation of snow depth and SWE (using the numerical models COUP and DeltaSnow) that assimilates the manual weekly snow-course measurements. Details on these snow measurements can be found in Stähli, M. and Gustafsson, D. 2006. Hydrol. Proc., 20, 411-428. doi: 10.1002/hyp.6058.

Further information on the methods and sensors can be found at https://www.wsl.ch/alptal .

A first version of this data set (for the period 1968-2017) was uploaded in June 2018 at the occasion of the 50-year anniversary. This original data set was updated in February 2021 (with data from 2018 and 2019), and this data set was used for a longterm trend analysis, submitted for publication in a special issue of Hydrological Processes. A second update of the data set (with data from 2020 to 2022) was uploaded in March 2023.

alptal

display_name: alptal

first-order-catchment

display_name: first-order-catchment

meteorological-data

display_name: meteorological-data

runoff

display_name: runoff

snow

display_name: snow

subalpine

display_name: subalpine

en: Longterm hydrological observatory Alptal (central Switzerland)


en: shortwave-radiation radiation longwave-radiation weisfluhjoch davos

en: Metadata

en: DATA ACCESS

en: ASRB radiation station at the Weissfluhjoch versuchsfeld.

en: Parameter file

en: Description of ASRB parameters.

en: Processing doc

en: Description of processing code that was ported to R by P. Frei (2016).

en:
Incoming and outgoing shortwave and longwave 2 min radiation measurements at the Weissfluhjoch research site, Davos, CH. The experimental site at the Weissfluhjoch (WFJ, 46.83 N, 9.81 E) is located at an altitude of 2540 m in the Swiss Alps near Davos. During the winter months, almost all precipitation falls as snow at this altitude. As a consequence, a continuous seasonal snow cover builds up every winter, with a maximum snow height ranging from 153–366 cm over the period 1934–2012. The measurement site is located in an almost flat part of a southeast oriented slope.

 References
1. Marty, C., Philipona, R., Frohlich, C., Ohmura, A.. Altitude dependence of surface radiation fluxes and cloud forcing in the alps: results from the alpine surface radiation budget network. 2002. Theoretical and Applied Climatology. Volume 72. Issue 3-4. 137-155. http://dx.doi.org/10.1007/s007040200019. 10.1007/s007040200019.
2. Christoph Marty. Surface Radiation, Cloud Forcing and Greenhouse Effect in the Alps. 2000. Institute fuer Klimaforschung ETH. Zuercher Klima-Schriften. Volume 79. http://e-collection.library.ethz.ch/eserv/eth:23491/eth-23491-01.pdf.

davos

display_name: davos

longwave-radiation

display_name: longwave-radiation

radiation

display_name: radiation

shortwave-radiation

display_name: shortwave-radiation

weisfluhjoch

display_name: weisfluhjoch

educ

en: Education, culture and sport

en: ASRB_WFJVF: Shortwave and longwave radiation measurements (2 min) at the Weissfluhjoch research site, Davos


digitizing-historical-plague

maintainer: Christian Ginzler

title_for_slug: digitizing-historical-plague

en: plague-mapping yersinia-pestis historical-plague plague-inventory plague-outbreaks bubonic-plague black-death palaeo-epidemiology

en: We present newly digitized data on 6,929 plague outbreaks that occurred between 1347 and 1900 AD across Europe. The data base on an inventory initially published 1976. For georeferencing the information of Tele Atlas 2009 was used. The coordinates are in the reference systems ETRS89 and WGS84.

black-death

display_name: black-death

bubonic-plague

display_name: bubonic-plague

historical-plague

display_name: historical-plague

palaeo-epidemiology

display_name: palaeo-epidemiology

plague-inventory

display_name: plague-inventory

plague-mapping

display_name: plague-mapping

plague-outbreaks

display_name: plague-outbreaks

yersinia-pestis

display_name: yersinia-pestis

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: Digitizing historical plague


maintainer: Anita C. Risch

en: soil nutrient-network soil-chemistry grassland global mineralization soil-biology worldwide

en:
site.code: Site code

Continent: Continent

sampleID: Sample ID

nn.latitude: Lattitude

nn.longitude: Longitude

bioclim.T.ann: Mean annual temperature (°C)

bioclim.T.var: Temperature variability (°C)

bioclim.T.q.wet: Temperature of the wettest quarter (°C)

bioclim.T.q.dry: Temperature of the driest quarter (°C)

bioclim.T.q.warm: Temperature of the warmest quarter (°C)

bioclim.P.ann: Mean annual preciptiation (mm)

bioclim.P.q.wet: Precipitation of the wettest quarter (mm)

ch.pH: pH

ch.WSK.vol: Water holding capacity (vol%)

ch.bulkdensity.gcm3: Bulk density (g cm-3)

ch.porespace: Pore space (vol%)

ch.sand.perc: Soil texture: sand (%)

ch.silt.perc: Soil texture: silt (%)

ch.clay.perc: Soil texture: clay (%)

ch.NO3start.mgg: NO3 at the beginning of the incubation (mgkg)

ch.Ntot.perc: Total soil N (%)

ch.Ctot.perc: Total soil C (%)

ch.Corg.perc: Soil organic C (%)

ch.netNminfield.mgkgd: Realised soil net N mineralisation (mg kg-1 d-1)

ch.netNminlab.mgkgd: Potential soil ne N mineralisation (mg kg-1 d-1)

archaea.cpg.log: Ammonia oxidising archaea (archaeal amoA gene copies g-1 soil)

bacteria.cpg.log: Ammonia oxidising bacteria (bacterial amoA gene copies g-1 soil)

micr.biom: Microbial biomass (ug g-1 soil)

ch.CtoN: C to N ratio

ch.netNnitriffield.mgkgd.sqrt: Realised soil net nitrification, transformed (mg kg-1 d-1)

ch.netNammoniffield.mgkgd.sqrt: Realised soil net ammonification, transformed (mg kg-1 d-1)

ch.netNnitriflab.mgkgd.sqrt: Potential soil net nitrification, transformed (mg kg-1 d-1)

ch.netNammoniflab.mgkgd.sqrt: Potential soil net ammonifiation, transformed (mg kg-1 d-1)

en:
This dataset contains all data on which the following publication below is based.

Paper Citation:

Risch, A. C.; Zimmermann, S.; Ochoa-Hueso, R.; Schütz, M.; Frey, B.; Firn, J. L.; Fay, P. A.; Hagedorn, F.; Borer, E. T.; Seabloom, E. W.; et al. Soil net nitrogen mineralisation across global grasslands. Nat. Commun. 2019, 10 (1), 4981 (10 pp.). doi.org/10.1038/s41467-019-12948-2

Please cite this paper together with the citation for the datafile.

We conducted coordinated measurements of realised and potential soil net Nmin, and assessed water holding capacity, bulk density, C and N content, texture, pH, pore space, microbial biomass, and archaeal (AOA) and bacterial (AOB) ammonia oxidiser abundance using identical materials and methods across 30 grasslands on six continents. The sites covered a globally relevant range of climatic and edaphic conditions. Climate data was obtained from worldclim - Global climate data https://www.worldclim.org/

global

display_name: global

grassland

display_name: grassland

mineralization

display_name: mineralization

nutrient-network

display_name: nutrient-network

soil

display_name: soil

soil-biology

display_name: soil-biology

soil-chemistry

display_name: soil-chemistry

worldwide

display_name: worldwide


en: eemma tracers stable-isotopes end-member-mixing-analysis mixing-models emma

en: vignette data

en: A simple data set for the vignette script

en: eemma user's guide

en: A brief user's guide to EEMMA, with illustrations using a simple data set

en: An R script that performs ensemble end-member mixing analysis

en: eemma vignette script

en: An R script for the vignettes (simple data analysis demonstrations) shown in the user's guide

mimetype: application/octet-stream

en:
The R script eemma.R, which implements Ensemble End-Member Mixing Analysis (EEMMA) to estimate source fractions in mixtures, exploiting information contained in time-series correlations among tracer time series.

A brief user's guide, a demonstration script, and a demonstration data set are also provided, to accompany Kirchner, J.W., Mixing models with multiple, overlapping, or incomplete end-members, quantified using time series of a single tracer, Geophysical Research Letters, 2023.

The user's guide is available for public use under Creative Commons CC-BY-SA. Public use of the scripts is permitted under GNU General Public License 3 (GPL3); for details see https://www.gnu.org/licenses/

eemma

display_name: eemma

emma

display_name: emma

end-member-mixing-analysis

display_name: end-member-mixing-analysis

mixing-models

display_name: mixing-models

stable-isotopes

display_name: stable-isotopes

tracers

display_name: tracers

en: eemma.R, an R script for Ensemble End-Member Mixing Analysis


global-cryosphere-watch-data-survey

maintainer: Mathias Bavay

title_for_slug: global-cryosphere-watch-data-survey

en: data-portal gcw automatic-publication data-exchange data-usage

en: Third party data usage

en: Data interoperability survey

en: Two surveys on the topic of data usage where conducted for the Global Cryosphere Watch data portal. The first one focused on the data provider point of view while the second one focused on the data user point of view. 37 data providers (ie institutions) worldwide provided their answers for the first survey (from fall 2017 until summer 2018) while 54 users (contacted through various mailing list such as the Cryolist) answered the questions on their third party data usage (fall 2019 until January 2020).

automatic-publication

display_name: automatic-publication

data-exchange

display_name: data-exchange

data-portal

display_name: data-portal

data-usage

display_name: data-usage

gcw

display_name: gcw

educ

en: Education, culture and sport

en: Global Cryosphere Watch data survey


intratrait

maintainer: Christian Rixen

title_for_slug: intratrait

en: neighbour-interactions plant-traits elevation-range cold-adapted-plants climate-change elevation-gradient

en: Plant trait data along elevation gradients on mountains

en:
This data set was used to test whether species specialized to high elevations or with narrow elevational ranges show more conservative (i.e. less variable) trait responses across their elevational distribution, or in response to neighbours, than species from lower elevations or with wider elevational ranges. We did so by studying intraspecific trait variation of 66 species along 40 elevational gradients in four countries (Switzerland, Australia, New Zealand, China) in both hemispheres. As an indication of potential neighbour interactions that could drive trait variation, we also analysed plant species’ height ratio, its height relative to its nearest neighbour.
The following traits and parameters were measured and are available in this data set:
As an indication of plant stature, we measured vegetative and generative height, where vegetative height was distance from soil to highest vegetative leaf and generative height was distance to the highest point on the reproductive shoot. As a measure of reproductive investment, we noted the presence of flowers on the randomly chosen individuals (see below). As a measure of individual and genet basal area, we measured individual plant and patch diameters, in two dimensions (along the largest diameter and perpendicular to it). In clonal plant species, plant diameter was equivalent to an individual rosette, whereas patch diameter referred to the whole genet and could represent the size of a tuft, tussock or cushion. For genera with more singular growth forms (e.g., some Gentiana species) plant and patch diameter were the same. The two diameter measurements were made at right angles, allowing estimates of patch and plant areas to be calculated as an ellipse (i.e., area = 0.5 a 0.5 b Π). All traits were measured on ten randomly selected individuals per site. Flower count data was considered in a binary fashion on a per individual basis (because for some species individuals only produce one flower when flowering) so that the presence or absence of flower(s) was a nominal value between 0 and 10 for each species at each site. We then collected at least three leaves (up to 30 for small and light leaves) from each of the first three individuals selected from each species for determination of leaf dry matter content (LDMC) and specific leaf area (SLA). For calculations of LDMC and SLA, fresh leaves were scanned on a flatbed scanner to determine leaf area. Leaves were then weighed on a balance to a precision of +/- 0.001g, prior to being air dried and reweighed with a balance to a precision of +/- 0.0001g. LDMC was calculated by dividing dry leaf mass by fresh leaf mass. SLA was calculated by dividing leaf area by dry leaf mass. Additionally, within an area of 10 cm diameter around the target individual, we determined the tallest neighbouring species and measured its vegetative and generative height, and estimated the percent cover of the target species, other vegetation, rock, and bare soil.
For more details see Rixen et al. 2022, Journal of Ecology.

climate-change

display_name: climate-change

cold-adapted-plants

display_name: cold-adapted-plants

elevation-gradient

display_name: elevation-gradient

elevation-range

display_name: elevation-range

neighbour-interactions

display_name: neighbour-interactions

plant-traits

display_name: plant-traits

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: intratrait


en: long-term meteorology precipitation meteo par wind-speed relative-humidity swiss-forest-lab temperature climate-change

en: Data plot of the field station (NEF)

en: Data overview for air temperature, relative humidity, precipitation, PAR, wind speed.

en: Site photo of the field station (NEF)

en: Site photo of the field station from the side.

en: Field station data (NEF)

en: Data file.

en: Data plot of the forest station (NEB)

en: Forest station data (NEB)

en: Site photo of the forest station (NEB)

en: Site photo of the forest station from below (viewing upwards the slope).

en: Site aerial photo (Neunkirch)

en: Site aerial photo from both Neunkirch stations. Source: Google. 2016. Site aerial photo from both Neunkirch stations. Retrieved November 11, 2016, from https://www.google.ch/maps

en: High quality meteorological data are needed for long-term forest ecosystem research, particularly in the light of global change. The long-term data series published here comprises almost 20 years of measurements for two meteorological stations in Neunkirch in Switzerland where one station is located within a natural deciduous forest stand (NEB) with European beech (_Fagus sylvatica_; 160 yrs), sycamore maple (_Acer pseudoplatanus_; 160 yrs) and lime trees (_Tilia sp._; 110 yrs) as dominant tree species. A second station is situated in the very vicinity outside of the forest (field station, NEF). The meteorological time series are presented in hourly time resolution of air temperature, relative humidity, precipitation, photosynthetically active radiation (PAR) and wind speed. Neunkirch is part of the Long-term Forest Ecosystem Research Programme (LWF) established and maintained by the Swiss Federal Research Institute WSL.

long-term

display_name: long-term

meteo

display_name: meteo

meteorology

display_name: meteorology

par

display_name: par

precipitation

display_name: precipitation

relative-humidity

display_name: relative-humidity

swiss-forest-lab

display_name: swiss-forest-lab

temperature

display_name: temperature

wind-speed

display_name: wind-speed

en: Neunkirch, Switzerland: Long-term forest meteorological data from the Long-term Forest Ecosystem Research Programme (LWF), from 1997 onwards


maintainer: Frank Techel

en: avalanche-forecasting avalanche-danger-level avalanche-bulletin avalanche-forecast verification

en: D_QC for forecasting seasons 2020/2021 - 2022/2023.

en: D_QC for forecasting seasons 2001/2002 until 2019/2020.

en:
The data set contains the re-analyzed (or quality-checked) regional avalanche danger levels (D_QC) for Switzerland.

D_QC relates to dry-snow avalanche conditions only. Measuring the avalanche danger level D is not possible; forecast, nowcast, and hindcast assessments of D are judgments by humans interpreting data. However, combining several pieces of information indicating the same D, it can be expected that it is more likely that D_QC represents the avalanche conditions well.

For the **forecasting seasons 2001/2002 until 2019/2020**, the approach to obtain D_QC is described in detail in Appendix A of [Pérez-Guillén et. al. (2022)](https://nhess.copernicus.org/articles/22/2031/2022/nhess-22-2031-2022.html).

For the **forecasting seasons 2020/2021 and later**, D_QC is derived using the following approach:
1. *Combination of forecast (D_forecast) and nowcast (D_nowcast)*: If there was only one assessment available by an observer after a day in the field for a region, and if D_forecast = D_nowcast --> D_QC = D_forecast.
2. *Combination of several nowcast assessments (D_nowcast)*: If two (or more) observers agreed (or majority opinion) in their (independent) assessments of D_nowcast after a day in the field in the same warning region. --> D_QC = D_nowcast.
3. *Hindcast analysis (D_hindcast)*: In Switzerland, avalanche forecasters re-evaluate all situations when D = 4 (high) or D = 5 (very high) were either forecast, should have been forecast, or when forecasters discussed given one of these two levels but had not given them. Generally, two forecasters assess each situation. In these cases, D_QC = D_hindcast. The hindcast analysis, only available since the forecasting season 2020/2021, replaces what was step (2) in Appendix A of [Pérez-Guillén et. al. (2022)](https://nhess.copernicus.org/articles/22/2031/2022/nhess-22-2031-2022.html).

All other cases - ties in case of (1) or (2), no new information from the warning region in question, or if no D_hindcast was available - are not considered quality-checked, and are, thus, not contained in the data set.

In addition to D_QC, the file contains information on the elevation and aspect, where D_QC likely prevails.
- The indicated elevation is the mean of the respective elevations in (1), (2), or (3). At danger level 1 (low), when no elevation is indicated in the Swiss forecast, a value of 1500 m is set.
- For the four cardinal aspects N, E, S, and W, a value of 1 means that there was agreement that D was reached in this aspect and a value of 0 means that there was agreement that D was not reached in this aspect. Intermediate values correspondingly mark disagreements in the assessments.

avalanche-bulletin

display_name: avalanche-bulletin

avalanche-danger-level

display_name: avalanche-danger-level

avalanche-forecast

display_name: avalanche-forecast

avalanche-forecasting

display_name: avalanche-forecasting

verification

display_name: verification

educ

en: Education, culture and sport

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: Re-analyzed regional avalanche danger levels in Switzerland


maintainer: Ueli Reber

en: policy-documents switzerland bgb environmental--policy policy-analysis text-corpus biodiversity

en: Replication files

en:
 Introduction

The ZIP file contains all data and code to replicate the analyses reported in the following paper.

Reber, U., Fischer, M., Ingold, K., Kienast, F., Hersperger, A. M., Grütter, R., & Benz, R. (2022). Integrating biodiversity: A longitudinal and cross-sectoral analysis of Swiss politics. *Policy Sciences*. [https://doi.org/10.1007/s11077-022-09456-4](https://doi.org/10.1007/s11077-022-09456-4)

If you use any of the material included in this repository, please refer to the paper. If you use (parts of) the text corpus, please also refer to the sources used for its compilation listed below. The content of the texts may not be changed.

 Data folder

The data folder contains the following files.

* _corpus.parquet_: Text corpus of Swiss policy documents
* _dict_de.csv_: Biodiversity dictionary (German)
* _dict_fr.csv_: Biodiversity dictionary (French)
* _dict_it.csv_: Biodiversity dictionary (Italian)
* _topic_labels.csv_: labels/codes for policy sectors
* _topics.csv_: labels/codes for policy sectors

The corpus and the dictionary were compiled by the authors specifically for this project. The labels/codes for policy sectors are based on the [coding scheme](http://ws-old.parlament.ch/affairs/topics) of the Swiss Parliament.

 Text corpus

The text corpus consists of 439,984 Swiss policy documents in German, French, and Italian from 1999 to 2018. The corpus was compiled from the following source between 2020-10-01 and 2021-01-31.

* Transcripts and parliamentary businesses (e.g. questions, motions, parliamentary initiatives) via the [Web Services (WS)](https://www.parlament.ch/de/%C3%BCber-das-parlament/fakten-und-zahlen/open-data-web-services) provided by the Swiss Parliament
* The official compilation of federal legislation ("Amtliche Sammlung", AS) via [opendata.swiss](https://opendata.swiss/de/dataset/official-compilation-of-federal-legislation-bs-as-1947-2018) provided by the Swiss Federal Archives (SFA)
* The federal gazette ("Bundesblatt") via [fedlex.admin.ch](https://www.fedlex.admin.ch/de/fga/index)
* Decisions of federal courts via [entscheidsuche.ch (ES)](https://entscheidsuche.ch/)

The corpus is stored in a single data frame to use with R saved as [PARQUET](https://parquet.apache.org/) file (corpus.parquet). The data frame has the following structure.

* _text_id_: Unique identifier for each text (source information as prefix, e.g. "t_")
* _doc_type_: Document type (see coding scheme below)
* _branch_: Government branche (1 legislative, 2 executive, 3 judicative)
* _stage_: Stage of policy process (1 drafting, 2 introduction, 3 interpretation)
* _year_: Year of publication
* _topic_: Policy sector (coding scheme in separate file in data folder)
* _lang_: Language (de, fr, it)
* _text_: Text

The following list contains the coding scheme for the doc_type variable.

* 101: Federal gazette // Draft for public consultation ("Vernehmlassungsverfahren")
* 102: Federal gazette // Explanation of draft for parliament ("Botschaft")
* 103: Federal gazette // Strategy, action plan
* 104: Federal gazette // Federal council decree ("Bundesratsbeschluss")
* 105: Federal gazette // (Simple) Federal decree ("(Einfacher) Bundesbeschluss")
* 106: Federal gazette // General decree ("Allgemeinverfügung")
* 107: Federal gazette // Treaty ("Übereinkommen")
* 108: Federal gazette // Treaty ("Abkommen")
* 109: Federal gazette // Draft for parliament ("Entwurf")
* 110: Federal gazette // Report ("Bericht")
* 111: Federal gazette // Report of parliamentary comission ("Bericht")
* 112: Federal gazette // Report of federal council ("Bericht")
* 201: Parl. businesses // Submitted text
* 202: Parl. businesses // Reason text
* 203: Parl. businesses // Federal council response
* 204: Parl. businesses // Initial situation
* 205: Parl. businesses // Proceedings
* 301: Parl. transcripts // Speech of MP
* 302: Parl. transcripts // Speech of federal council
* 401: Federal legislation // Legal text of the official compilation (law, ordinances, etc.)
* 501: Court decisions // Federal Supreme Court
* 502: Court decisions // Federal Criminal Court
* 503: Court decisions // Federal Administrative Court

 Code folder

The code folder contains all R code for the analyses. The files are numbered chronologically.

* _1_classifier_training.R_: Training of classifiers for classification of policy sectors
* _2_classifier_application.R_: Classification of documents in corpus
* _3_dictionary_application.R_: Biodiversity indexing of documents in corpus
* _4_stm_truncation.R_: Truncation of indexed documents to keep only relevant parts
* _5_stm_translation.R_: Translation of FR and IT documents to DE
* _6_stm_model.R_: Preprocesssing and structural topic model
* _7_plots.R_: Plots and numbers as included in the paper

The code/functions folder contains custom functions used in the scripts, e.g. to support topic model interpretation.

Package versions and setup details are noted in the code files.

 Contact

Please direct any questions to Ueli Reber (ueli.reber@eawag.ch).

bgb

display_name: bgb

biodiversity

display_name: biodiversity

environmental--policy

display_name: environmental--policy

policy-analysis

display_name: policy-analysis

policy-documents

display_name: policy-documents

switzerland

display_name: switzerland

text-corpus

display_name: text-corpus

en: Replication files for "Integrating biodiversity: A longitudinal and cross-sectoral analysis of Swiss politics"


maintainer: Ionut Iosifescu Enescu

en: hpc open-science jupyter-notebooks reproducibility open-data open-source research-data-management

en: Open Science Support @ WSL (Poster)

en:
This poster was originally created for the swissuniversities Open Science Action Plan: Kick-Off Forum, and showed to the audience on 17.10.2019. It illustrates how the environmental data portal EnviDat provides the tools for fostering Open Science and Reproducibility of scientific research at WSL.

Supporting open science is a highly relevant user requirement for EnviDat and for implementing FAIR (Findability, Accessibility, Interoperability and Reusability) principles at dataset level.
EnviDat encourages WSL scientists to complement data publication with a complete description of research methods and the inclusion of the open source software, code or scripts used for processing the dataset or for obtaining the published results. By openly publishing open software (e.g. as Jupyter notebooks) alongside research data sets, researchers can contribute to mitigate reproducibility issues.

EnviDat also promotes and supports, where possible and practical, the publication of software as Jupyter notebooks. Jupyter notebooks provide a solution for improved documentation and interactive execution of open code in a wide range of programming languages (Python, R, Octave/Matlab, Java or Scala). These programming languages are widely used in environmental research at WSL and well supported by the Jupyter-compatible kernels. We have sucessfully interfaced EnviDat-hosted notebooks with the WSL High-Performance Computing (HPC) Linux Cluster through a JupyterHub/JuypterLab beta installation on the HPC cluster implemented in close collaboration with the WSL IT-Services.
For existing software that cannot be easily migrated to Jupyter Notebooks, the Open Science and Reproducibility is assisted by containerisation. We have proven that several Singularity containers can successfully run on WSL's HPC cluster.

Finally, the researchers can upload the data/results complemented by code (e.g. as Jupyter Notebooks, or Singularity containers) and any additional documentation in EnviDat. Consequently, they will receive a DOI for the entire dataset, which they can reference in their science paper in order to publish a more reproducible research.

_License_: This poster is released by WSL and the EnviDat team to the public domain under a Creative Commons 4.0 CC0 "No Rights Reserved" international license. You can reuse this poster in any way you want, for any purposes and without restrictions.

hpc

display_name: hpc

jupyter-notebooks

display_name: jupyter-notebooks

open-data

display_name: open-data

open-science

display_name: open-science

open-source

display_name: open-source

reproducibility

display_name: reproducibility

research-data-management

display_name: research-data-management

en: Open Science Support at the Swiss Federal Research Institute WSL. The EnviDat Concept


en: mars model snow sediment-transport erosion

en: Datasets of Figure 2

en: Datasets of Figure 3a

en: Datasets of Figure 4a

en: Datasets of Figure 4b

en: Datasets of Figure 3b

en:
The files contain the datasets used to produce Figures 2, 3, and 4 of the manuscript ([doi: 10.1002/2016GL071822](http://dx.doi.org/10.1002/2016GL071822)).

 Manuscript Abstract:
Despite being the main sediment entrainment mechanism in aeolian transport, granular splash is still poorly understood. We provide a deeper insight into the dynamics of sand and snow ejection with a stochastic model derived from the energy and momentum conservation laws. Our analysis highlights that the ejection regime of uniform sand is inherently different from that of heterogeneous sand. Moreover, we show that cohesive snow presents a mixed ejection regime, statistically controlled either by energy or momentum conservation depending on the impact velocity. The proposed formulation can provide a solid base for granular splash simulations in saltation models, leading to more reliable assessments of aeolian transport on Earth and Mars.

erosion

display_name: erosion

mars

display_name: mars

model

display_name: model

sediment-transport

display_name: sediment-transport

snow

display_name: snow

en: Energy- and momentum-conserving model of splash entrainment in sand and snow saltation


maintainer: Lisa Hülsmann

en: forest-reserves empirical-mortality-models inventory-data tree-mortality tree-growth

en: Calibration data

en:
A set of three consecutive inventories was used to generate records for the calibration of mortality models based on trees that were alive in the first and second inventory and either dead or alive in the third inventory.

 Meta data
Reserve: Name of the forest reserve

Plot: Permanent plot number

 Tree data
Species: Latin species name (or species group, cf. _Quercus_ spp.)

y: Status of the tree with 0 = alive and 1 = dead

dt: Length of the mortality period (years)

DBH: Diameter at breast height (mm) of the second inventory

relBAI: Annual relative basal area increment (-) calculated based on the first and the second DBH measurement as the compound annual growth rate of the trees basal area

 Stand data
_All stand variables were calculated for the second inventory._

mDBH: Mean diameter at breast height (mm)

iqrDBH: Interquartile range of diameter at breast height (mm)

BA: Basal area per hectare (m2 ha-1)

N: Number of trees per hectare (ha-1)

 Climate data
_Both climate variables were calculated for the period between the second and the third inventory._

P: Mean annual precipitation sum (mm)

mT: Mean annual air temperature (°C)

en:
The dataset comprises > 90 000 records from inventories in 54 strict forest reserves in [Switzerland](https://www.wsl.ch/de/wald/biodiversitaet-naturschutz-urwald/naturwaldreservate.html) and [Lower Saxony / Germany](http://naturwaelder.de/) along a considerable environmental gradient. It was used to develop parsimonious, species-specific mortality models for 18 European tree species based on tree size and growth as well as additional covariates on stand structure and climate.

 Inventory data
Measurements had been conducted repeatedly on up to 14 permanent plots per reserve for up to 60 years with re-measurement intervals of 4 - 27 years. The permanent plots vary in size between 0.03 and 3.47 ha. The inventories provide diameter measurements at breast height (DBH) and information on the species and status (alive or dead) of trees with DBH ≥ 4 cm for Switzerland and ≥ 7 cm for Germany.

 Data selection
We excluded three permanent plots where at least 80 % of the trees died during an interval of 10 years, and mortality could be clearly assigned to a disturbance agent. Mortality in the remaining stands was rather low, with a mean annual mortality rate of 1.5 % and strong variation between plots from 0 to 6.5 % (assessed for trees of all species with DBH ≥ 7 cm).
We only used data from permanent plots with at least 20 trees per species to obtain reliable plot-level mortality rates even for species with low mortality rates (about 5 % during 10 years), and selected tree species occurring on at least 10 plots to cover sufficient ecological gradients. This led to a dataset of 197 permanent plots and 18 tree or shrub species: _Abies alba_ Mill., _Acer campestre_ L., _Acer pseudoplatanus_ L., _Alnus incana_ Moench., _Betula pendula_ Roth, _Carpinus betulus_ L., _Cornus mas_ L., _Corylus avellana_ L., _Fagus sylvatica_ L., _Fraxinus excelsior_ L., _Picea abies_ (L.) Karst, _Pinus mugo_ Turra, _Pinus sylvestris_ L., _Quercus pubescens_ Willd., _Quercus_ spp. (_Q. petraea_ Liebl. and _Q. robur_ L.; not properly differentiated in the Swiss inventories), _Sorbus aria_ Crantz, _Tilia cordata_ Mill. and _Ulmus glabra_ Huds..

 Predictors of tree mortality
We considered tree size and growth as key indicators for mortality risk. Radial stem growth between the first and second inventory and DBH at the second inventory were used to predict tree status (alive or dead) at the third inventory. To this end, the annual relative basal area increment (relBAI) was calculated as the compound annual growth rate of the trees basal area. Additional covariates on stand structure and climate comprise mean annual precipitation sum (P), mean annual air temperature (mT), the mean and the interquartile range of DBH (mDBH, iqrDBH), basal area (BA) and the number of trees (N) per hectare.

 Further information
For further information, refer to Hülsmann _et al_. (in press) How to kill a tree – Empirical mortality models for eighteen species and their performance in a dynamic forest model. _Ecological Applications_.

empirical-mortality-models

display_name: empirical-mortality-models

forest-reserves

display_name: forest-reserves

inventory-data

display_name: inventory-data

tree-growth

display_name: tree-growth

tree-mortality

display_name: tree-mortality

educ

en: Education, culture and sport

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: Calibration data for empirical mortality models of 18 European tree species


maintainer: Franziska Gerber

en: antarctica cryowrf python aws consistent

en: Scripts to preprocess (and download for some databases) atmospheric weather station data. Furthermore, a list of stations and a map can be created to have an overview.

en:
There are many sources providing atmospheric weather station data for the Antarctic continent. However, variable naming, timestamps and data types are highly variable between the different sources. The published python code intends to make processing of different AWS sources from Antarctica easier. For all datasets that are taken into account variables are renamed in a consistent way. Data from different sources can then be handled in one consistent python dictionary.

The following data sources are taken into account:

* AAD: Australian Antarctic Division (https://data.aad.gov.au/aws)
* ACECRC: Antarctic Climate and Ecosystems Cooperative Research Centre by the Australian Antarctic Division
* AMRC: Antarctic Meteorological Research Center (ftp://amrc.ssec.wisc.edu/pub/aws/q1h/)
* BAS: British Antarctic Survey (ftp://ftp.bas.ac.uk/src/ANTARCTIC_METEOROLOGICAL_DATA/AWS/; https://legacy.bas.ac.uk/met/READER/ANTARCTIC_METEOROLOGICAL_DATA/)
* CLIMANTARTIDE: Antarctic Meteo-Climatological Observatory by the italian National Programme of Antarctic Research (https://www.climantartide.it/dataaccess/index.php?lang=en)
* IMAU: Institute for Marine and Atmospheric research Utrecht (Lazzara et al., 2012), https://www.projects.science.uu.nl/iceclimate/aws/antarctica.ph
* JMA: Japan Meteorological Agency (https://www.data.jma.go.jp/antarctic/datareport/index-e.html)
* NOAA: National Oceanic and Atmospheric Administration (https://gml.noaa.gov/aftp/data/meteorology/in-situ/spo/)
* Other/AWS_PE: Princess Elisabeth (PE), KU Leuven, Prof. N. van Lipzig, personal communication
* Other/DDU_transect: Stations D-17 and D-47 (in transect between Dumont d’Urville and Dome C, Amory, 2020)
* PANGAEA: World Data Center (e.g. König-Langlo, 2012)

Important notes

* Information about data sources is available. Some downloading scripts are included in the provided code. However, users should make sure to comply with the data providers terms and conditions.
* Given changing download options of the differnent institutions the above links may not permanently work and data has to be retrieved by the user of this dataset.
* No quality control is applied in the provided preprocessing software - quality control is up to the user of the datasets. Some dataset are quality controlled by the owner.

Acknowledgements
--------------------------
We thank all the data providers for making the data publicly available or providing them upon request. Full acknowledgements can be found in Gerber et al., submitted.

References
---------------
Amory, C. (2020). “Drifting-snow statistics from multiple-year autonomous measurements in Adélie Land, East
Antarctica”. The Cryosphere, 1713–1725. doi: 10.5194/tc-14-1713-2020

Gerber, F., Sharma, V. and Lehning, M.: CRYOWRF - a validation and the effect of blowing snow on the Antarctic SMB, JGR - Atmospheres, submitted.

König-Langlo, G. (2012). “Continuous meteorological observations at Neumayer station (2011-01)”. Alfred Wegener
Institute, Helmholtz Centre for Polar and Marine Research, Bremerhaven, PANGAEA, doi: 10.1594/PANGAEA.
775173

antarctica

display_name: antarctica

aws

display_name: aws

consistent

display_name: consistent

cryowrf

display_name: cryowrf

python

display_name: python

en: Preprocessing Antarctic Weather Station (AWS) data in python


maintainer: Ionuț Iosifescu Enescu

en: huge map 100GB

media_type: image/tiff

format: TIFF

mimetype: image/tiff

en: map 0.2GB

en: map 1GB

en: Bulk Data Access

en: Link to the S3 bucket where all the data resources can be downloaded in bulk

en: map 0.5GB

en: map 2GB

en: large map 10GB

en: map preview 0.5MB

en:
The attached data are some large GIS raster files (GeoTIFFs) made with Natural Earth data. Natural Earth is a free vector and raster map data @ naturalearthdata.com. The data used for creating these large files was the "Cross Blended Hypso with Shaded Relief and Water". Data was concatenated to achieve larger and larger files. Internal pyramids were created, in order that the files can be opened easily in a GIS software such as QGIS or by a (future) GIS data visualisation module integrated in EnviDat.

Made with Natural Earth. Free vector and raster map data @ naturalearthdata.com

gis

display_name: gis

large-files

display_name: large-files

natural-earth

display_name: natural-earth

qgis

display_name: qgis

en: Large GIS raster data derived from Natural Earth Data (Cross Blended Hypso with Shaded Relief and Water)


en: avalanche avalanche-size natural-avalanches machine-learning snowpack-model

en: Data set AV3 was used for validation of the avalanche-day classifier (Sections 2.1.3 and 3.3(1) in Mayer et al.).

en: Data set AV1 was used for training the avalanche-day classifier (Sections 2.1.1, 2.2, and 3.1 in Mayer et al.).

en: Data set DL was used for validation of the avalanche-day classifier and the avalanche-size estimator. The data set contains the quality-checked danger levels merged with the respective SNOWPACK simulations (Sections 2.3 and 3.3(2) in Mayer et al.).

en: Data set AV2 used for training the avalanche-size estimator (Sections 2.1.2 and 3.2 in Mayer et al.)

en:
The data set contained in this repository was used in the analysis by Mayer et al. (2023):
Mayer, S. I., Techel, F., Schweizer, J., and van Herwijnen, A.: Prediction of natural dry-snow avalanche activity using physics-based snowpack simulations, EGUsphere, https://doi.org/10.5194/egusphere-2023-646, 2023.

avalanche

display_name: avalanche

avalanche-size

display_name: avalanche-size

machine-learning

display_name: machine-learning

natural-avalanches

display_name: natural-avalanches

snowpack-model

display_name: snowpack-model

educ

en: Education, culture and sport

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: Data-set for prediction of natural dry-snow avalanche activity and avalanche size using physics-based snowpack simulations