maintainer: Rebecca Mott

en: snow-patch dischmex turbulent-sensible-heat-fluxes eddy-covariance-measurements patchy-snow-covers

en: Gletschboden setup

media_type: image/png

en: Background map based on data © 2014/2016 swisstopo (JD100042)

format: PNG

mimetype: image/png

en: Eddy-covariance measurement with an ultrasonic anemometer (DA-600, Kaijo-Denki) in 0.3 m on a daily basis.

en: Eddy-covariance measurement with an ultrasonic anemometer (R.M. Young Company) in 3.3 m.

en: Eddy-covariance measurement with an ultrasonic anemometer (CSAT3, Campbell Scientific Inc.) in 3.2 m on a daily basis.

en: Eddy-covariance measurement with an ultrasonic anemometer (CSAT3, Campbell Scientific, Inc.) in 2.2 m.

en: Eddy-covariance measurement with an ultrasonic anemometer (R.M. Young Company) in 3.5 m.

en: Eddy-covariance measurement with an ultrasonic anemometer (CSAT3, Campbell Scientific, Inc.) in 2.6 m.

en: Eddy-covariance measurement with an ultrasonic anemometer (R.M. Young Company) in 0.7 m.

en: Output explanation

en: Eddy-covariance measurement with an ultrasonic anemometer (CSAT3, Campbell Scientific Inc.) in 1.7 m on a daily basis.

en:
This dataset contains eddy-covariance measurements in the ablation period of 2014-2016. Measurements were taken from two turbulence towers over a long-lasting snow patch, which are 5 m apart from each other (2014 and 2015). The turbulence towers were equipped with two YOUNG ultrasonic anemometers mounted 0.7 m (in 2014) and 3.3 m (in 2015) above snow-free ground, two ultrasonic anemometers (CSAT3, Campbell Scientific, Inc.) mounted at 2.6 m (in 2014) and 2.2 m (in 2015) above snow-free ground and one anemometer (DA-600, Kaijo Denki) mounted at 0.3 m above snow surface.

The measurement setup changed in 2016 and includes a measurement above the snow-free ground in upwind direction (Swiss coordinates: 790191/176689). The measurement tower is equipped with one ultrasonic anemometer (CSAT3, Campbell Scientific, Inc.) in 3.3 m above the snow-free ground. Additionally, one measurement tower is installed above the long-Lasting snow patch and equipped with the same setup as 2015.

Turbulence data were sampled at a frequency of 20 Hz. The processing of the data to quality controlled fluxes has been done with the Biomicrometeorology flux software (Thomas et al., 2009). The program applies plausibility tests and a despiking test after Vickers and Mahrt (1997) on the measured data. The routine further applies a time-lag correction and considers the deployment (e.g. the sonic azimuth). A frequency response correction (Moore, 1986) is done and a three-dimensional rotation is performed. Finally, quality assurance/quality control (QA/QC) flags after Foken et al., (2004) are issued and fast Fourier transform power and co-spectra are calculated. The change in snow height is considered in the post-processing for every measurement day. The turbulence data were averaged to 30 minute intervals.

dischmex

display_name: dischmex

eddy-covariance-measurements

display_name: eddy-covariance-measurements

patchy-snow-covers

display_name: patchy-snow-covers

snow-patch

display_name: snow-patch

turbulent-sensible-heat-fluxes

display_name: turbulent-sensible-heat-fluxes

en: DISCHMEX - Impact of extreme land-surface heterogeneity on micrometeorology over spring snow-cover


snow-drift-station-snow-and-air-data

maintainer: Benjamin Walter

title_for_slug: snow-drift-station-snow-and-air-data

en: snow raclets temperature snow-temperature snow-depth snow-height

state: active

type: dataset

en: Relative Humidity

en: The relative humidity (%) was measured with a Campbell CS-215 at a height of 2.2 m above ground. The time is given in UTC+1.

format: XLS

en: Snow Depth

en: The snow depth (cm) was measured with a Lufft SHM-31 which was mounted at 1.7 m above ground. The time is given in UTC+1.

en: Air Temperature

en: The air temperature (°C) was measured with a Campbell CS-215 which was mounted at a height of 2.2 m above ground. The time is given in UTC+1.

en: Snow Surface Temperature

en: The snow surface temperature (°C) was measured with a Campbell SI-111 at 0.7 m above ground. The time is given in UTC+1.

en: Snow and air data was monitored at Gotschnagrat (LON: 46.859 LAT: 9.849) by an infrarot radiometer (Campbell SI-111) for snow temperature (°C), a snow height sensor (Lufft SHM-31) for snow height change (cm) and a temperature and humidity sensor (Campbell CS-215) for air temperature (°C) and relative humidity (%). No filter was applied to the sensors and the smapling frequency was 1 Hz.

raclets

display_name: raclets

snow

display_name: snow

snow-depth

display_name: snow-depth

snow-height

display_name: snow-height

snow-temperature

display_name: snow-temperature

temperature

display_name: temperature

educ

fr: Éducation, culture et sport

de: Bildung, Kultur und Sport

en: Education, culture and sport

it: Istruzione, cultura e sport

envidat

fr: EnviDat: le portail de données environnementales

de: EnviDat: das Umwelt-Datenportal

en: EnviDat: the Environmental Data Portal

it: EnviDat: il portale dei dati ambientali

fr: EnviDat est le portail de données du WSL; il offre un accès uniformisé et réglementé aux données de surveillance et de recherche en matière d’environnement. Ce portail est capable d’héberger et de publier des ensembles de données précieuses et uniques, qui sont partagées aux quatre coins de la planète. Ce faisant, EnviDat favorise la recherche et contribue à l’avancement des sciences environnementales.

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

de: EnviDat ist das Datenportal der WSL für einen einheitlichen und verwalteten Zugang zu Umweltdaten aus Monitoring- und Forschungsprojekten. Auf dem Portal können Datensätze gehostet und veröffentlicht werden. Durch die weltweite Bereitstellung einzigartiger und wertvoller Datensätze leistet EnviDat einen Beitrag zur Forschung im Bereich der Umweltwissenschaften.

it: EnviDat è il portale dati del WSL che fornisce un accesso unificato e gestito ai dati di monitoraggio ambientale e di ricerca. Il portale ha la capacità di ospitare e pubblicare serie di dati preziosi e unici che vengono condivisi in tutto il mondo. Così facendo, EnviDat promuove la ricerca e contribuisce al progresso della scienza ambientale.

political_level: other

wsl

capacity: public

type: organization

approval_status: approved

key: guid

key: uri

value: Envidat Harvester

en: Snow Drift Station - Snow and Air Data


irkis-soil-moisture-measurements-davos

maintainer: Nander Wever

title_for_slug: irkis-soil-moisture-measurements-davos

en: meteo-station soil-moisture meteorological-measurements dischma-catchment davos

en: IRKIS soil moisture data (zip file)

en: Compressed archive (zip) containing soil moisture measurements, as well as meteorological measurements and interpolated meteorological time series.

format: SERVICE

en:
Meteorological and soil moisture measurements from soil moisture stations installed from October 2010 - October 2013 in the area surrounding Davos, in particular in the Dischma catchment.

There are in total 7 stations: 1202, 1203, 1204, 1205, 222, 333 and SLF2. For each of the stations, there is a:

* vwc_[stn].smet: containing the soil moisture measurements

* station_[stn].smet: in-situ measured meteorlogical parameters. Note, the quality of these measurements for stations 1202, 1203, 1204 and 1205 is very low, with data gaps. Use this data with care. For stations 222, 333 and SLF2, data quality is high and only the default cautiousness should be applied.

* interpolatedmeteo_[stn].smet contains per stations a dataset derived by interpolating from several stations in the Davos area to the stations location. This dataset was generated from the output of the Alpine3D model, of which simulations are presented in the Wever et al. (2017) manuscript.

At the soil moisture measurement sites, Decagon 10HS sensors were installed, at 10, 30, 50, 80 and 120 cm depth. Per depth 2 sensors were installed, labelled A and B in the datafiles. Note that at stations 1203, 1204 and 1205, sensors were only installed at 10, 30 and 50 cm depth.

The files follow the SMET format: https://models.slf.ch/docserver/meteoio/SMET_specifications.pdf and metadata for the stations can be found in the header of the smet files.

Please cite the Wever et al. (2017) reference when using this data in publications.

For a more detailed description, please refer to: Wever, N., Comola, F., Bavay, M., and Lehning, M.: Simulating the influence of snow surface processes on soil moisture dynamics and streamflow generation in an alpine catchment, Hydrol. Earth Syst. Sci., 21, 4053-4071, https://doi.org/10.5194/hess-21-4053-2017, 2017.

davos

display_name: davos

dischma-catchment

display_name: dischma-catchment

meteo-station

display_name: meteo-station

meteorological-measurements

display_name: meteorological-measurements

soil-moisture

display_name: soil-moisture

en: IRKIS Soil moisture measurements Davos


maintainer: Matthias Haeni

en: meteo wind-speed climate-change temperature swiss-forest-lab long-term par relative-humidity precipitation meteorology

en: Site photo of the field station (BTF)

en: Site photo of the field station from the side.

mimetype: image/jpeg

en: Site photo of the forest station (BTB)

en: Site photo of the forest station from the side.

en: Field station data (BTF)

media_type: text/csv

en: Data file.

format: CSV

mimetype: text/csv

en: Data plot of the forest station (BTB)

media_type: application/pdf

en: Data overview for air temperature, relative humidity, precipitation, PAR, wind speed.

format: PDF

mimetype: application/pdf

en: Data plot of the field station (BTF)

en: Site aerial photo (Bettlachstock)

en: Site aerial photo from both Bettlachstock stations. Source: Google. 2016. Site aerial photo from both Bettlachstock stations. Retrieved November 11, 2016, from https://www.google.ch/maps

en: High quality meteorological data are needed for long-term forest ecosystem research, particularly in the light of global change. The long-term data series published here comprises almost 20 years of measurements for two meteorological stations in Bettlachstock in Switzerland where one station is located within a natural mixed forest stand (BTB) with European beech (_Fagus sylvatica_; 170-190 yrs), European silver fir (_Abies alba_; 190 yrs) and Norway spruce (_Picea abies_; 200 yrs) as dominant tree species. A second station is situated in the very vicinity outside of the forest (field station, BTF). The meteorological time series are presented in hourly time resolution of air temperature, relative humidity, precipitation, photosynthetically active radiation (PAR) and wind speed. Bettlachstock is part of the Long-term Forest Ecosystem Research Programme (LWF) established and maintained by the Swiss Federal Research Institute WSL.

climate-change

display_name: climate-change

long-term

display_name: long-term

meteo

display_name: meteo

meteorology

display_name: meteorology

par

display_name: par

precipitation

display_name: precipitation

relative-humidity

display_name: relative-humidity

swiss-forest-lab

display_name: swiss-forest-lab

wind-speed

display_name: wind-speed

en: Bettlachstock, Switzerland: Long-term forest meteorological data from the Long-term Forest Ecosystem Research Programme (LWF), from 1997 onwards


maintainer: EnviDat Support

en: radiation wind atmospheric-conditions temperature-profiles precipitation

en: Latest data from Stillberg climate station

en: This dataset is outdated and has been replaced with an updated version (see description).

en: Site photo 2

en: This site photo is outdated and has been replaced with an updated version (see description).

en: DATA ACCESS

en: This data access is outdated and has been replaced with an updated version (see description).

en: Site photo 3

en: STB2 CSV

en: Overview plot

en: This overview plot is outdated and has been replaced with an updated version (see description).

en: Site photo 1

en: README

media_type: text/plain

en: This description is outdated and has been replaced with an updated version (see description).

format: TXT

en:
 Important

This EnviDat entry is outdated. The most recent, usable version of the data can be found under the new EnviDat entry "Long-term meteorological station Stillberg, Davos, Switzerland at 2090 m a.s.l.." The entry can be found under this link <https://www.envidat.ch/dataset/meteo-stillberg> and with this DOI https://doi.org/10.16904/envidat.396.

atmospheric-conditions

display_name: atmospheric-conditions

radiation

display_name: radiation

temperature-profiles

display_name: temperature-profiles

wind

display_name: wind

educ

en: Education, culture and sport

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: Long-term meteorological and snow station at 2090 m a.s.l., Stillberg, Davos, Switzerland (1975 - present)


en: soil frost-change-velocity precipitation ground-temperature aridity sdms

media_type: image/tiff

en: Soil organic carbon content modified from SoilGrids

format: TIFF

en: Soil clay content modified from SoilGrids

en: Mean annual temperature modified from CHELSA

en: Precipitation seasonality from CHELSA

en: Frost change frequency modified from CHELSA

en: Mean diurnal range modified from CHELSA

en: Precipitation of driest quarter modified from CHELSA

en: Soil pH modified from SoilGrids

en: The dataset contains seven environmental layers (average annual temperature, aridity [annual precipitation divided by annual potential evapotranspiration], frost change frequency, precipitation in the driest quarter, mean diurnal temperature range, and precipitation seasonality) modified from CHELSA (https://chelsa-climate.org/) and three soil layers (soil organic matter content, pH water, and clay content) modified from SoilGrids (https://soilgrids.org/).

aridity

display_name: aridity

frost-change-velocity

display_name: frost-change-velocity

ground-temperature

display_name: ground-temperature

sdms

display_name: sdms

soil

display_name: soil

en: Environmental layers for SDM simulations (GDPlants)


en: water-scarcity reservoirs water-supply climate-change water-demand

en: Water demand version 2 (corrected version)

media_type: application/zip

format: ZIP

mimetype: application/zip

en: Water demand (deprecated)

en:
Warning: please use the corrected version 2, since this file contains errors for certain categories such as Livestock, Industry or Houshold.

Water demand estimates for the 307 medium-sized catchments for different categories for current and future conditions. One text file is provided per demand category. One column corresponds to one catchment (IDs compare to shapefile), The data are provided at monthly resolution in mm/d and can be converted to volumes by using the catchment area. E.g.
Q[mm/d] * catchment area [m²] /1000 = Q[m³/d]
or to obtain discharge in m³/s
Q[mm/d] * catchment area [m²]/1000/24/3600 = Q [m³/s].
Future irrigation and hydropower water demand are provided per climate model chain.

en: Reservoir volumes

en: Reservoir volume for the 307 medium-sized catchments for different storage categories: natural lakes, artificial reservoirs, reservoirs for artificial snow production, drinking water reservoirs, and usable volumes of natural lakes. Unit: Mio m³. One column per catchment (see shapefile).

en: Shapefile of 307 catchments in Switzerland

en: Shapefile of 307 catchments for which estimates of water supply, demand, and reservoir volumes are provided. The OBJECTID entry corresponds to the catchment ID which is used as a reference in the other datasets provided.

en: Water supply

en: Simulated discharge series for a reference period 1981-2010 and till the end of the century. Data are provided for 39 climate model chains and a control run based on the observed meteorology. Data are provided at daily resolution (mm/d).

en:
The dataset Hydro-CH2018 reservoirs provides estimates of current and future water supply, water demand, and storage volumes for 307 medium-sized catchments in Switzerland.
Water supply for current (1981-2010) and future (2070-2099) climate conditions was simulated using the hydrological model PREVAH. For modeling current water supply, observed meteorological time series were used as input, while simulated meteorological time series derived from 39 model chains of the CH2018 initiative were used as an input for simulating future climate conditions.

Water demand was estimated for six categories:

- 1) Drinking water (households and tourism),
- 2) industry (second and third sector),
- 3) artificial snow production,
- 4) agriculture (irrigation and livestock feeding),
- 5) ecology (residual flows), and
- 6) hydropower.

Future estimates consider changes in demand related to population growth and changes in the hydrological conditions.
Storage volumes are provided for natural lakes (storage capacities and usable volumes), artificial reservoirs, reservoirs for artificial snow production, and drinking reservoirs.

A detailed description of the simulation and estimation procedures can be found in

*  Brunner, M.I., Björnsen Gurung, A., Zappa, M., Zekollari, H., Farinotti, D., Stähli, M., 2019. Present and future water scarcity in Switzerland: Potential for alleviation through reservoirs and lakes. Sci. Total Environ. 666, 1033–1047. https://doi.org/10.1016/j.scitotenv.2019.02.169.

This dataset contains the following information:

1.	Shapefile with the 307 medium-sized Swiss catchments.
2.   Textfiles with the water supply simulations for the control run and the 39 climate model chains (one file per chain) at daily resolution for the 307 catchments.
3.	Textfiles with the current and future demand estimates per category at monthly resolution for the 307 catchments.
4.	Textfiles with the storage volumes per category and catchment.

climate-change

display_name: climate-change

reservoirs

display_name: reservoirs

water-demand

display_name: water-demand

water-scarcity

display_name: water-scarcity

water-supply

display_name: water-supply

en: Hydro-CH2018 reservoirs


en: urbanization land-use-change land-use statistical-model landscape-services switzerland modeling

en: Data for Assessing potential landscape service trade-offs driven by urbanization in Switzerland

en:
The provided folder structure follows the set up of the scripts.
Data is only provided when it has been fully produced by us, otherwise dummies are given.
For data that will be produced by one of the scripts, no dummies are given.
The folders may contain sub-folders, which would be filled if the scripts were all run

 00_Analysis_Data
Data produced throughout the process of the calibration and projection that is later needed for analysis

 01_Raw_Data
Primary data from external sources that were used to compile the rasters and numbers used during the calibration and projection of landscape transitions as well as service calculation

 02_Prepared_Data
Data that will be prepared for further use by scripts are put in here
Additionally it contains the parameter sheets for the transition predictors that we compiled

 03_Model_Data
 Model outputs
Folder were the projection models statistics will be saved
 Models
Folder into which the actual transition models will be saved
 Residuals
Folder into which data on models residuals will be saved for future use

 04_Projected_Data
The output of the projections will be saved into this folder

 05_Service_Data
Any service calculations will be saved in here

 06_Results_Analysis
Any Analysis plots and tables as well as intermediate data will be saved here in the respective sub-folder

en: Scripts for Assessing potential landscape service trade-offs driven by urbanization in Switzerland

en:
Scripts ordered by their main purpose within sequential folders in this ReadMe marked with

Within the folders the capital letters refer to the parallel or sequential use of the scripts; scripts here in ReadMe are marked with

 00_Function Scripts
 Functions.r
Script containing several functions for analyzing statistical models: cohen.kappa, meva.table, D2, max-Tss, plot-TSS

 Service_functions.R
Script containing functions for calculating all services and returning sums (and median for bd and rec) as well as rasters

 01_Data Preparation
 A_AS_raster_preparation.R
Preparation of the land use rasters for the years 1985, 1997, and 2009 based on the original Arealstatistik (AS/ASCH); Assigning our categories and assining new values to all "construction sites" for calibrating the models
For model projection starting point (2009) and for service calculations (all ASCH years) the "other" categories were assigned to the land use categories based on dominant neighbor, so that there were no empty cells
Creation of water & mountainous area raster that stayed stable throughout the projections
Creation of MFH raster (2009), to have as base for all new projection years, as this category never becames any other

 B_Factors_preparation.R
Preparation of the factor rasters that were used to calculate service values per cell (see Table 2): LWfactor, Transportation, Vol, Rivers, Lakes, slope, TWW, Hazard_risk

 B_Predictors_preparation.R
Preparation of the raster of the predictors used for calibrating (ASCH years) and projecting (stable) the transition models that do not depend on the land use categories: Temperature (ASCH years), solar radiation (stable), Public transportation access (stable), Elevation (stable), Workers density (ASCH years), Population change (ASCH transitions)

 B_Regions_preparation.R
Preparation of bioregions as raster to be used to mask asxxxx later to calculated services and land use area just for one region

 C_Pred_proj.R
Projecting the dynamic predictors into the future for projecting the land use transitions with the model: Linear extrapolations for workers densities and population; more detailed extrapolation of temperature (based on data for all stations that matched between the temp table we used for the calibration period and the projections from CS2M, and then making a spatial interpolation for all years based on the interpolation of temperature for all years per station)

 02_Model calibration
 A_Bioreg_pred_corr.R
Calculating correlation between the predictors for each bioregion and land use category, Output are those with too high correlation so that one predictor can be removed from transitions were both predictors occur

 A_trans_numbers_bioreg.R
Calculate transition numbers for each bioregion to decide which transitions to primarily consider

 B_Bioreg_ext_eval.R
Calculating TSS based on the external evaluation for the bioregion transitions that happened often enough to try to model them (calibration data: 85-97, evaluation data: 97-09)

 B_Bioreg_int_eval.R
Calculating TSS based on the internal evaluation for the bioregion transitions that happened often enough to try to model them (calibration data: 70%, evaluation data: 30%)

 C_Bioreg_TSS_analysis.R
Extracting TSS numbers from internal and external evaluation, calculating mean and median for each transition for each region for each evaluation method and saving as csv per region to be able to select only the transitions with high enough model performance

 D_Bioreg_Models_for_prediction.R
Calibration of the models that were then used to project land use transitions into the future; calibrated separately for each bioregion

 E_Residuals_trans_models.R
Calculation of Moran's I statistics to analyze the residuals of the land use transition models

 03_Projections
 A_Bioreg_Projections_run.R
Master script for: Extrapolaitng into the future with the regional models and then assembling for each time step to calculate new AS predictors; Several Outputs: txt file to test for NAs in Predictors, txt file with random seed number for sampling, txt file with times for calculation steps (check progress of script while running), csv sheet with projected transition frequencies, tif-rasters for every region and time step, pdf with raster plot for every region and time step

 04_Service calculation
 A_Bioreg_as_services.R
Calculate services per bioregion for years 1985, 1997, 2009

 A_Service_calculation_bioregions.R
Extracting service numbers(sums) per bioregions for all projection runs and storing them in a list of matrixes to be available for further plotting; can be run for swiss wide projections or regional ones

 05_Analysis
 A_Bioreg_ASCH_development.R
Extracting the occurrence of each category per region for all runs (first part), then for ASCH years, and then plotting them nicely; only works for regional projections

 A_Bioreg_Predictors_importanceD2.R
Calculating D2 for each transition and each considered predictor from bivariate models to get value of importance

 B_Bioreg_Pred_imp_analysis.R
Using calculated D2 to sort Predictors according to their importance for each transition

 A_Bioreg_Spatial_results_analysis.R
Plotting randomly sampled runs for ASCH and services to analyses their spatial development

 A_Bioreg_Transition_numbers_check_v1.R
Analyzing the frequency for all transitions for all regions and producing the point plots for each transition separately

 A_Bioreg_Transition_numbers_check_v2.R
Analyzing percentage and numbers of all transitions but plotting them per region and originating ASCH category

 B_Transition_Analysis.R
Further Analysis of transition numbers

 A_Service_analysis.R
Plotting of the service development for bioregions in several ways for analyzing

en:
Data and scripts of publication:

Madleina Gerecke, Oskar Hagen, Janine Bolliger, Anna M. Hersperger, Felix Kienast, Bronwyn Price, Loïc Pellissier (2019) Assessing potential landscape service trade-offs driven by urbanization in Switzerland. Palgrave communications.

Contains land use projections for Switzerland and scripts and data for these projections as well as the calculation of landscape services.

Data Folder:
Contains sub-folder with the data necessary for this study (provided were no copyright issues, otherwise placeholders with descriptions), and folders where produced data may be stored

Scripts Folder:
Contains scripts organized into subfolders depending on their purpose

Note: Some abbreviations within the scripts and data are derived from German words and not English.

land-use

display_name: land-use

land-use-change

display_name: land-use-change

landscape-services

display_name: landscape-services

modeling

display_name: modeling

statistical-model

display_name: statistical-model

switzerland

display_name: switzerland

urbanization

display_name: urbanization

educ

en: Education, culture and sport

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: Land use projections and services for Switzerland


high-resolution-climate-data-for-europe

title_for_slug: high-resolution-climate-data-for-europe

en: europe air-temperature precipitation cordex eur11 maximum-temperature daily-climate minimum-temperature

en: CHELSA EUR11 Technical Documentation

en: As the CHELSA project is continuously expanded, certain new parameters, time scales etc. are not included anymore in the original publication (Karger et al. 2017). We are therefore provide this document as a guideline of the current climatic parameters available and will expand it as new parameters or time periods will become available. Please refer to the version history for changes made in the document.

en: Data Access

en:
High-resolution information on climatic conditions is essential to many applications in environmental and ecological sciences. Here we present downscaled climate data for the CORDEX EUR11 domain at a high resolution of 30 arc sec. The temperature algorithm is based on statistical downscaling of atmospheric temperature lapse rates. The precipitation algorithm incorporates orographic predictors including wind fields, valley exposition, and boundary layer height. The resulting data consist of a daily temperature and precipitation timeseries.

The data is distributed under a: Creative Commons: Attribution 4.0 International (CC BY 4.0) license.

air-temperature

display_name: air-temperature

cordex

display_name: cordex

daily-climate

display_name: daily-climate

europe

display_name: europe

maximum-temperature

display_name: maximum-temperature

minimum-temperature

display_name: minimum-temperature

precipitation

display_name: precipitation

en: High resolution climate data for Europe


snow-drift-station-micro-rain-radar

title_for_slug: snow-drift-station-micro-rain-radar

en: raclets snow mountain precipitation radar rain

en: MRR data of period 4

en: The dataset contains measurements between March 13 and March 22, 2019, with time in UTC. The parameters and specifications are given in MRR_parameters.pdf. The zip folder contains hourly data files in netCDF format and a log file, reporting the instrument status.

en: MMR Data Period 1

en: The dataset contains measurements between March 1 and March 5, 2019, with time in UTC. The parameters and specifications are given in MRR_parameters.pdf. The zip folder contains hourly data files in netCDF format and a log file, reporting the instrument status.

en: Parameter MRR

en: The PDF contains additional information on parameters which were set for the certain time periods (time in UTC).

en: MRR data of period 3

en: The dataset contains measurements between March 8 and March 13, 2019, with time in UTC. The parameters and specifications are given in MRR_parameters.pdf. The zip folder contains hourly data files in netCDF format and a log file, reporting the instrument status.

en: MRR data Period 2

en: The dataset contains measurements between March 5 and March 8, 2019, with time in UTC. The parameters and specifications are given in MRR_parameters.pdf. The zip folder contains hourly data files in netCDF format and a log file, reporting the instrument status.

en: The instrument (MRR, Metek) was mounted at Gotschnagrat (LON: 46.859 LAT: 9.849) at a height of 1 m above snow surface (at the beginning of the campaign) with an orientation of 22° with respect to North and a horizontal viewing direction. The sampling time was either 5 s or 10 s, depending on the settings at the specific period. The MRR produces standard outputs like radar reflectivity, doppler velocity, etc., and additional information can be found [here](https://metek.de/de/product/mrr-2/).

mountain

display_name: mountain

raclets

display_name: raclets

radar

display_name: radar

rain

display_name: rain

snow

display_name: snow

en: Snow Drift Station - Micro Rain Radar


lidar-davos-wolfgang

maintainer: Patric Seifert

title_for_slug: lidar-davos-wolfgang

en: raclets tropos clouds lidar polly

en: Raman Lidar Davos

en: A portable Raman lidar system (Polly) from Leibnitz Institute for Tropospheric Research (Tropos) was deployed at Davos Wolfgang (LON: 9.853594, LAT: 46.835577). Please use this [link](http://polly.tropos.de/?p=lidarzeit&Ort=39), to be directly forwarded to the Davos location and select the date of interest from the calendar (bold numbers). The data can be requested directly at the Polly team.

clouds

display_name: clouds

lidar

display_name: lidar

polly

display_name: polly

tropos

display_name: tropos

educ

en: Education, culture and sport

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: LIDAR Davos Wolfgang


maintainer: Sofia Pagliarin

en: copernicus soil-sealing urban-atlas milan barcelona imperviousness

en: Shareable project in Esri ArcGIS format including the HRL IMD data in raster format for each of the territorial boundaries as specified in letter a)-h), see Dataset description

en: Information on data sources

en:
Dataset description

This dataset is a recalculation of the Copernicus 2015 high resolution layer (HRL) of imperviousness density data (IMD) at different spatial/territorial scales for the case studies of Barcelona and Milan. The selected spatial/territorial scales are the following:

 * a)	Barcelona city boundaries
 * b)	Barcelona metropolitan area, Àrea Metropolitana de Barcelona (AMB)
 * c)	Barcelona greater city (Urban Atlas)
 * d)	Barcelona functional urban area (Urban Atlas)
 * e)	Milan city boundaries
 * f)	Milan metropolitan area, Piano Intercomunale Milanese (PIM)
 * g)	Milan greater city (Urban Atlas)
 * h)	Milan functional urban area (Urban Atlas)

In each of the spatial/territorial scales listed above, the number of 20x20mt cells corresponding to each of the 101 values of imperviousness (0-100% soil sealing: 0% means fully non-sealed area; 100% means fully sealed area) is provided, as well as the converted measure into squared kilometres (km2).

 Dataset composition

The dataset is provided in .csv format and is composed of:

_IMD15_BCN_MI_Sources.csv_: Information on data sources

 _IMD15_BCN.csv_: This file refers to the 2015 high resolution layer of imperviousness density (IMD) for the selected territorial/spatial scales in Barcelona:
 * a)	Barcelona city boundaries (label: bcn_city)
 * b)	Barcelona metropolitan area, Àrea metropolitana de Barcelona (AMB) (label: bcn_amb)
 * c)	Barcelona greater city (Urban Atlas) (label: bcn_grc)
 * d)	Barcelona functional urban area (Urban Atlas) (label: bcn_fua)

 _IMD15_MI.csv_: This file refers to the 2015 high resolution layer of imperviousness density (IMD) for the selected territorial/spatial scales in Milan:
 * e)	Milan city boundaries (label: mi_city)
 * f)	Milan metropolitan area, Piano intercomunale milanese (PIM) (label: mi_pim)
 * g)	Milan greater city (Urban Atlas) (label: mi_grc)
 * h)	Milan functional urban area (Urban Atlas) (label: mi_fua)

_IMD15_BCN_MI.mpk_: the shareable project in Esri ArcGIS format including the HRL IMD data in raster format for each of the territorial boundaries as specified in letter a)-h).

Regarding the territorial scale as per letter f), the list of municipalities included in the Milan metropolitan area in 2016 was provided to me in 2016 from a person working at the PIM.

In the IMD15_BCN.csv and IMD15_MI.csv, the following columns are included:

 * Level: the territorial level as defined above (a)-d) for Barcelona and e)-h) for Milan);
 * Value: the 101 values of imperviousness density expressed as a percentage of soil sealing (0-100%: 0% means fully non-sealed area; 100% means fully sealed area);
 * Count: the number of 20x20mt cells corresponding to a certain percentage of soil sealing or imperviousness;
 * Km2: the conversion of the 20x20mt cells into squared kilometres (km2) to facilitate the use of the dataset.

 Further information on the Dataset

This dataset is the result of a combination between different databases of different types and that have been downloaded from different sources. Below, I describe the main steps in data management that resulted in the production of the dataset in an Esri ArcGIS (ArcMap, Version 10.7) project.

 1. The high resolution layer (HRL) of the imperviousness density data (IMD) for 2015 has been downloaded from the official website of Copernicus. At the time of producing the dataset (April/May 2021), the 2018 version of the IMD HRL database was not yet validated, so the 2015 version was chosen instead. The type of this dataset is raster.

 2. For both Barcelona and Milan, shapefiles of their administrative boundaries have been downloaded from official sources, i.e. the ISTAT (Italian National Statistical Institute) and the ICGC (Catalan Institute for Cartography and Geology). These files have been reprojected to match the IMD HRL projection, i.e. ETRS 1989 LAEA.

 3. Urban Atlas (UA) boundaries for the Greater Cities (GRC) and Functional Urban Areas (FUA) of Barcelona and Milan have been checked and reconstructed in Esri ArcGIS from the administrative boundaries files by using a Eurostat correspondence table. This is because at the time of the dataset creation (April/May 2021), the 2018 Urban Atlas shapefiles for these two cities were not fully updated or validated on the Copernicus Urban Atlas website. Therefore, I had to re-create the GRC and FUA boundaries by using the Eurostat correspondence table as an alternative (but still official) data source. The use of the Eurostat correspondence table with the codes and names of municipalities was also useful to detect discrepancies, basically stemming from changes in municipality names and codes and that created inconsistent spatial features. When detected, these discrepancies have been checked with the ISTAT and ICGC offices in charge of producing Urban Atlas data before the final GRC and FUA boundaries were defined.

Steps 2) and 3) were the most time consuming, because they required other tools to be used in Esri ArcGIS, like spatial joins and geoprocessing tools for shapefiles (in particular dissolve and area re-calculator in editing sessions) for each of the spatial/territorial scales as indicated in letters a)-h).

Once the databases for both Barcelona and Milan as described in points 2) and 3) were ready (uploaded in Esri ArcGIS, reprojected and their correctness checked), they have been ‘crossed’ (i.e. clipped) with the IMD HRL as described in point 1) and a specific raster for each territorial level has been calculated. The procedure in Esri ArcGIS was the following:

 * Clipping: Arctoolbox > Data management tools > Raster > Raster Processing > Clip. The ‘input’ file is the HRL IMD raster file as described in point 1) and the ‘output’ file is each of the spatial/territorial files. The option "Use Input Features for Clipping Geometry (optional)” was selected for each of the clipping.
 * Delete and create raster attribute table: Once the clipping has been done, the raster has to be recalculated first through Arctoolbox > Data management tools > Raster > Raster properties > Delete Raster Attribute Table and then through Arctoolbox > Data management tools > Raster > Raster properties > Build Raster Attribute Table; the "overwrite" option has been selected.

 Other tools used for the raster files in Esri ArcGIS have been the spatial analyst tools (in particular, Zonal > Zonal Statistics). As an additional check, the colour scheme of each of the newly created raster for each of the spatial/territorial attributes as per letters a)-h) above has been changed to check the consistency of its overlay with the original HRL IMD file. However, a perfect match between the shapefiles as per letters a)-h) and the raster files could not be achieved since the raster files are composed of 20x20mt cells.

The newly created attribute tables of each of the raster files have been exported and saved as .txt files. These .txt files have then been copied in the excel corresponding to the final published dataset.

barcelona

display_name: barcelona

copernicus

display_name: copernicus

imperviousness

display_name: imperviousness

milan

display_name: milan

soil-sealing

display_name: soil-sealing

urban-atlas

display_name: urban-atlas

en: Soil sealing Barcelona and Milan different territorial levels


maintainer: Michael Lehning

en: snow-cover alpine3d alpine3d-simulations snow snow-hydrology snow-distribution alpine-precipitation

en: ADS datasets and simulation inputs

en: The file contains the ADS datasets of snow depth and input data used for simulations.

en:
Dataset (Model input, snow distribution and validation) for the precipitation scaling paper, which should be cited along with the data set citation.

This data is useful for distributed hydrological modelling or other tasks that involve the study of snow distribution and precipitation in the high Alpine.

The format of the data is for Alpine3D (models.slf.ch) model runs but other models could be used, too.

Please cite:

_Vögeli, C., Lehning, M., Wever, N., Bavay M., 2016: Scaling Precipitation Input to Spatially Distributed Hydrological Models by Measured Snow Distribution., Front. Earth Sci. 4: 108. doi: 10.3389/feart.2016.00108._

Dataset is provided as a single zip file.
The archive contains two directories, the valuable distributed snow depth maps for the landscape Davos and the simulation input.
The archive also contains the file: "ReadMeMetadataDataSetPrecipitationScaling" which explains the data structure.

alpine-precipitation

display_name: alpine-precipitation

snow-cover

display_name: snow-cover

snow-distribution

display_name: snow-distribution

snow-hydrology

display_name: snow-hydrology

en: Precipitation Scaling Data Set (Vögeli et al., Frontiers)


maintainer: Lyu

en: species-richness pinales species-distribution-model fagales species-occurrence species-range-map

en: Occurrence maps for species of Fagales and Pinales with few records

en: Point_buffer.zip includes 267 occurrence maps of species that do not have enough occurrence data for polygon mapping.

en: Species range maps of species in Fagales and Pinales (with enough occurrences)

en: species_map.zip includes species 1690 range maps generated based on the integrated method described in Lyu et al., (2022). File names with (polygon) indicate that this map is only generated by polygon mapping, as there are not enough occurrences for SDMs.

en:
This database contains 1957 distribution maps of species from Fagales and Pinales constructed based on a method integrating polygon mapping and SDMs (Lyu et al., 2022).
To construct the maps, we first collected occurrence data from 48 different sources. According to the number of occurrences after data cleaning, three kinds of maps are constructed: (1) For species with more than 20 occurrences, we performed SDM and polygon mapping described in Lyu et al. (2022) and select the integration of the two layers as the distribution range; (2) For species with more than 4 but less than 20 occurrences, we only use polygon mapping to draw the distribution range; (3) For species with less than 4 occurrences, a 20-km buffer was generated around the occurrences as the distribution range. The maps were manually checked and evaluated (see Note S3 and Table S9 in Lyu et al., 2022 for details).

fagales

display_name: fagales

pinales

display_name: pinales

species-distribution-model

display_name: species-distribution-model

species-occurrence

display_name: species-occurrence

species-range-map

display_name: species-range-map

species-richness

display_name: species-richness

en: Species distribution maps of Fagales and Pinales (GDPlants)


soil-respiration-exclosure-experiment

title_for_slug: soil-respiration-exclosure-experiment

en: subalpine soil-respiration grazing grassland ungulates

en: Soil respiration Switzerland

en:
ID: Fence number

Year	:Year of sampling

mean.CO2: soil respiration measured with PP-systems SRC-1 soil respriation chamber attached to a EGM-4 infrared gas analyser; units CO2 g m-2 h-1

Grassland: Grasslands where fences were errected. Note that on large grasslands (STAB, GRIM, MING) 2 pairs of fences were errected (2 in short, 2 in tall-grass vegetation), on small grasslands (DADA, MARG, BOTS) only one pair of fences was errected (1 short-grass; one-tallgrass vegetation)

Fence: Fence number; un-even numbers on short-grass vegetation (1,3,5,7,9,11,13,15,17), even numbers on tall-grass vegetation (2,4,6,8,10,12,14,16,18)

Vegetation:	1 = shortgrass vegetation, 2 = tall-grass vegetation (9 replicate fences on each vegetation type)

Treatment	: 1 = all herbivores grazing, 2 = large ungulates (red deer, chamois) excluded

en:
Location of data collection
The Swiss National Park (SNP) is located in the southeastern part of Switzerland, and covers an area of 170 km2, 50 km2 of which is forested, 33 km2 is occupied by alpine and 3 km2 by subalpine grasslands. Elevations range from 1350 to 3170 m a.s.l., and mean annual precipitation and temperature are 871 mm and 0.6°C measured at the Park’s weather station in Buffalora (1980 m a.s.l.) between 1960 and 2009 (MeteoSchweiz 2011). Founded in 1914, the SNP received minimal human disturbance for almost 100 years (no hunting, fishing, or camping, visitors are not allowed to leave the trails). Large (> 1 ha) homogeneous patches of short- and tall-grass vegetation characterize the subalpine grasslands. The average vegetation height of short-grass vegetation is 2 to 5 cm. Red fescue (Festuca rubra L.), quaking grass (Briza media L.) and common bent grass (Agrostis tenuis Sipthrob) are the predominating plant species in this vegetation type. Tussocks of evergreen sedge (Carex sempervirens Vill.) and mat grass (Nardus stricta L.) are predominant in the tall-grass vegetation, which averages 20 cm in vegetation height (Schütz and others 2006). Short-grass vegetation developed in areas where cattle and sheep rested (high nutrient input) during agricultural land-use (from 14th century until 1914); tall-grass vegetation developed in areas where cattle and sheep used to graze, but did not rest (Schütz and others 2003, 2006). Herbivores were shown to consume > 60% of the biomass in short-grass compared to < 20% in tall-grass vegetation (Schütz and others 2006). The herbivore community present in the SNP can be divided into four groups based on body size/weight: large [red deer (Cervus elaphus L.) and chamois (Rupricapra rupricapra L.); 30 - 150 kg], medium [marmot (Marmota marmota L.) and snow hare (Lepus timidus L.); 3 – 6 kg], and small vertebrate herbivores (small rodents: e.g. Clethrionomys spp., Microtus spp., Apodemus spp.; 30 – 100 g) as well as invertebrates (e.g. grasshoppers, caterpillars, cicadas, < 5 g).

Experimental design
We selected 18 subalpine grassland sites (9 short-grass, 9 tall-grass vegetation). The sites were spread across the entire park on dolomite parent material at altitudes of 1975 to 2300 meters. At each site we established an exclosure network (fences) in spring 2009 (early June), immediately after snowmelt. Each exclosure network consisted of a total of five 2 × 3 m sized plots that progressively excluded the different herbivores listed above (further labeled according to the herbivore guilds that had access to the respective plots “All”, “Marmot/Mice/Invertebrates”, “Mice/Invertebrates”, “Invertebrates”, “None”). The “All” treatment was thus accessible to all herbivores, was not fenced and was located at least 5 m away from a 2.1 m tall and 7 × 9 m main fence that enclosed the other four treatments. This fence was constructed of 10 × 10 cm wooden posts and electrical equestrian tape (AGRARO ECO, Landi, Bern, Switzerland; 20 mm width) mounted at 0.7 m, 0.95 m, 1.2 m, 1.5 m and 2.1 m above the ground that were connected to a solar charged battery (AGRARO Sunpower S250, Landi, Bern, Switzerland). We also mounted non-electrically charged equestrian tape at 0.5 m to help exclude deer and chamois, yet allow marmots and hares to enter safely. Within each main fenced area we randomly established four 2 × 3 m plots: (1) The “Marmot/Mice/Invertebrates” plot remained unfenced, thus, with the exception of red deer and chamois, all herbivores were able to access the plot, (2) The “Mice/Invertebrates” plot consisted of a 90 cm high electric sheep fence (AGRARO Weidezaunnetz ECO, Landi, Bern, Switzerland; mesh size 10 × 10 cm) connected to the solar panel and excluded all medium sized mammals (marmots, hares), but provided access for small mammals and invertebrates, (3) The “Invertebrates” plot provided access for invertebrates only and was surrounded by 1 m high metal mesh (Hortima AG, Hausen, Schweiz; mesh size 2 × 2 cm), (4) The “None” plot was surrounded by a 1 m tall mosquito net (Sala Ferramenta AG, Biasca, Switzerland; mesh size 1.5 × 2 mm) to exclude all herbivores. This plot was covered with a roof constructed of a wooden frame lined with mosquito mesh that was mounted on the wooden corner posts. We also treated this plot with a biocompatible insecticide (Clean kill original, Eco Belle GmbH, Waldshut-Tiengen, Germany) when needed to remove insects that might have entered during data collection or that hatched from the soil.

!!! The here published data set only contains data for “All”, and “Marmot/Mice/Invertebrates” (= ungulates excluded) plots !!!

Data collection
In-situ soil CO2 emissions were measured with a PP-Systems SRC-1 soil respiration chamber (closed circuit) attached to a PP-Systems EGM-4 infrared gas analyzer (PP-Systems, Amesbury, MA, USA) on two randomly selected locations on one subplot within each of the 90 plots. For each measurement the soil chamber (15 cm high; 10 cm diameter) was placed on a permanently installed PVC collar (10 cm diameter) driven five centimeters into the soil at the beginning of the study (June 2009). The measurements were conducted between 0900 and 1700 hours every two weeks from early to early September 2009, 2010, 2011 and 2013. Freshly germinated plants growing within the PVC collars were removed prior to each measurement to avoid measuring plant respiration/photosynthesis. The two measurements collected per plot every two weeks were averaged.

Please acknowledge the funding of the study: funded by the Swiss National Science Foundation, SNF grant-no 31003A_122009/1 to Anita C. Risch, Martin Schütz and Flurin Filli

grassland

display_name: grassland

grazing

display_name: grazing

soil-respiration

display_name: soil-respiration

subalpine

display_name: subalpine

ungulates

display_name: ungulates

educ

en: Education, culture and sport

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: Soil respiration - exclosure experiment


maintainer: Yohann Chauvier

en: species-distribution taxonomy hard-limit ecoregions filtering synonyms occurrence-records flags accepted-name range-maps r-package conservation landsca gbif species-observations large-scale

en: wsl.gbif R package version 0.1 (deprecated)

en: Test version, not to be used.

en: gbif.range R package version 1.1 (current)

en: gbif.range R package version 0.2 (deprecated)

en: GitHub URL

en: Although species range may be obtained using expert maps or modeling methods, expert data is often species-limited and statistical models need more technical expertise as well as many species observations. When unavailable, such information may be extracted from the Global Biodiversity Information facility (GBIF), the largest public data repository inventorying georeferenced species observations worldwide. However, retrieving GBIF records at large scale may be tedious if users are unaware of specific tools and functions that need to be employed. Here we present *gbif.range*, an R library that contains automated methods to generate species range maps from scratch using in-house ecoregions shapefiles and an easy-to-use GBIF download wrapper. Finally, this library also offers a set of additional very useful parameters and functions for large GBIF datasets (generate doi, extract GBIF taxonomy, records filtering...). [gbif.range R project](https://github.com/8Ginette8/gbif.range)

accepted-name

display_name: accepted-name

conservation

display_name: conservation

ecoregions

display_name: ecoregions

filtering

display_name: filtering

flags

display_name: flags

gbif

display_name: gbif

hard-limit

display_name: hard-limit

landsca

display_name: landsca

large-scale

display_name: large-scale

occurrence-records

display_name: occurrence-records

r-package

display_name: r-package

range-maps

display_name: range-maps

species-distribution

display_name: species-distribution

species-observations

display_name: species-observations

synonyms

display_name: synonyms

taxonomy

display_name: taxonomy

en: gbif.range - An R package to generate species range maps based on ecoregions and a user-friendly GBIF wrapper


en: stable-water-isotopes stream-water precipitation geochemical-solutes spatially-distributed-sampling

en: The dataset contains daily measurements of volumes, isotopes and solutes of stream water as well as precipitation measured several locations; meteorological variables are added. Date: 18.07.2019

en:
This dataset contain measurements of solute and stable water isotopes in stream water and precipitation in the Alp catchment and two of its tributaries (between 2015 -2018) . The river Alp is a snow-dominated catchment situated in Central Switzerland characterized by an elevation range from 840 to 1898 m a.s.l. The dataset provides solutes (major anions and cations, trace metals) and stable water isotopes and water fluxes (precipitation rates, discharge) at daily intervals from several sampling locations.
An updated version of the isotope dataset is available here: https://www.doi.org/10.16904/envidat.242

geochemical-solutes

display_name: geochemical-solutes

precipitation

display_name: precipitation

spatially-distributed-sampling

display_name: spatially-distributed-sampling

stable-water-isotopes

display_name: stable-water-isotopes

stream-water

display_name: stream-water

en: Daily data of solute and stable water isotopes in stream water and precipitation in the Alp catchment, Central Switzerland


en: incoming longwave-radiation shortwave-radiation outgoing davos

en: Processing doc

en: DATA ACCESS

en: Metadata

en: Parameter file

mimetype: text/plain

en:
Incoming and outgoing shortwave and longwave 2 min radiation measurements in Davos Dorf, CH.

 References
1. Marty, C., Philipona, R., Frohlich, C., Ohmura, A.. Altitude dependence of surface radiation fluxes and cloud forcing in the alps: results from the alpine surface radiation budget network. 2002. Theoretical and Applied Climatology. Volume 72. Issue 3-4. 137-155. http://dx.doi.org/10.1007/s007040200019. 10.1007/s007040200019.
2. Christoph Marty. Surface Radiation, Cloud Forcing and Greenhouse Effect in the Alps. 2000. Institute fuer Klimaforschung ETH. Zuercher Klima-Schriften. Volume 79. http://e-collection.library.ethz.ch/eserv/eth:23491/eth-23491-01.pdf.

davos

display_name: davos

incoming

display_name: incoming

longwave-radiation

display_name: longwave-radiation

outgoing

display_name: outgoing

shortwave-radiation

display_name: shortwave-radiation

en: ASRB_DAV: Shortwave and longwave radiation measurements (2 min) in Davos Dorf


en: latent-semantic-analysis food-taste-similarity agro-food-trade food-preferences national-dishes

en: information on ingredients of national dishes

en: shows information of ingredients of all national dishes of 171 countries and their names

en: National dishes, migration data and data for bilateral food trade flows

en:
The data include information on national dishes, migration data and data for bilateral food
trade flows for 5 years as well as importer and exporter GDP, population, distance between
most populated cities, bilateral information on Preferential Trade Agreements, common
official primary langauge, common colonizer post-1945, colonial relationship for overall
171 countries. The final data set contains 145,350 observations (29,070 country pairs for
5 years)

en: dyadic food similarity measures, pairwise similarity and dissimilarity (chord diagram)

en:
The figures show the distribution of two dyadic food tastes similarity measures on the base of
the national dishes: (i) the Manhattan distance and the (ii) latent semantic analysis. The chord diagram
shows the results for country pairs with most and less similarity on basis of the LSA-approach.

en: The data described in this article were collected daily over the period 4 June 2018 to 23 August 2018 and contains information of several data sources. The database includes information on national recipes and their ingredients for 171 countries, measures for food taste similarities between all 171 countries as well as bilateral migration and agro-food trade data for 5 years. The database can be used for analyzing e.g., the relation between food preferences and international trade or food preferences and health outcomes (e.g., obesity) across countries.

agro-food-trade

display_name: agro-food-trade

food-preferences

display_name: food-preferences

food-taste-similarity

display_name: food-taste-similarity

latent-semantic-analysis

display_name: latent-semantic-analysis

national-dishes

display_name: national-dishes

educ

en: Education, culture and sport

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: Data of national dishes, their similarity and trade flows


maintainer: James W. Kirchner

en: sap-flow evapotranspiration ecohydrology diel-cycle streamflow diurnal-cycle snowmelt groundwater

en: MODIS EVI2 script

en: Google Earth Engine script for computing MODIS two-band enhanced vegetation index (EVI2) values and averaging them over subcatchments.

en: 30-minute time series

en: 30-minute hydrometeorological and ecohydrological time series.

en: Column descriptions for both data files, and map coordinates for all measurement locations.

en: Subcatchment polygons

en: Subcatchment polygons for use in the Google Earth Engine scripts.

en: MODIS NDSI script

en: Google Earth Engine script for computing MODIS normalized difference snow index (NDSI) values and averaging them over subcatchment areas.

en: Daily time series

en: Daily hydrometeorological and ecohydrological time series

en:
Hydrometerological and ecohydrological time series from Sagehen Creek and Independence Creek, Sierra Nevada, USA, illustrating hydrological responses to daily cycles in snowmelt and evapotranspiration forcing.

Data include 30-minute time series of

- weather variables,

- sap flow fluxes,

- groundwater levels (in two riparian transects of shallow groundwater wells),

- and stream stages (at 12 sites spanning a 500-meter elevation gradient),

and daily time series of

- temperature, precipitation, and snow water equivalent at three nearby snow telemetry stations

- diel cycle index values for groundwater levels and stream stages,

- and MODIS normalized difference snow index (NDSI) and enhanced vegetation index (EVI2) values averaged over selected subcatchments.

Google Earth Engine scripts for extracting the MODIS data are also provided.

diel-cycle

display_name: diel-cycle

diurnal-cycle

display_name: diurnal-cycle

ecohydrology

display_name: ecohydrology

evapotranspiration

display_name: evapotranspiration

groundwater

display_name: groundwater

sap-flow

display_name: sap-flow

snowmelt

display_name: snowmelt

streamflow

display_name: streamflow

en: Daily cycles in solar flux, snowmelt, transpiration, groundwater, and streamflow at Sagehen and Independence Creeks, Sierra Nevada, USA


global-cryosphere-watch-data-survey

maintainer: Mathias Bavay

title_for_slug: global-cryosphere-watch-data-survey

en: gcw automatic-publication data-portal data-usage data-exchange

en: Third party data usage

en: Data interoperability survey

en: Two surveys on the topic of data usage where conducted for the Global Cryosphere Watch data portal. The first one focused on the data provider point of view while the second one focused on the data user point of view. 37 data providers (ie institutions) worldwide provided their answers for the first survey (from fall 2017 until summer 2018) while 54 users (contacted through various mailing list such as the Cryolist) answered the questions on their third party data usage (fall 2019 until January 2020).

automatic-publication

display_name: automatic-publication

data-exchange

display_name: data-exchange

data-portal

display_name: data-portal

data-usage

display_name: data-usage

gcw

display_name: gcw

educ

en: Education, culture and sport

envidat

en: EnviDat: the Environmental Data Portal

en: Global Cryosphere Watch data survey


en: Description

en: Full Data Description

en: Data Source

en: Coordinates of Grid Points

en: Hourly Gridded Wind Power Time Series

en:
This dataset consist of simulated hourly power production from an Enercon E82 Turbine at 100 m hub-height. It describes the hourly power output a 1MW turbine would produce in each 0.01° grid cell for the years 2016 and 2017.

100 m wind speed data was taken from the COSMO-1 model (Consortium for Small-scale Modeling 2017), which has a 0.01° horizontal resolution. The domain covered is the whole of Switzerland, with the exclusion of lakes. As such, the number of 0.01◦ pixels within Switzerland amounts to 48657.
Conversion to power output was done based on the power curve of the Enercon E82 Turbine. As power output is lower at altitude due to lower air density, we corrected for this effect as described in (Kruyt et al. 2017).

Please cite the following paper in connection with the dataset:

Paper Citation:
 > _Bert Kruyt, Jérôme Dujardin, and Michael Lehning: Improvement of wind power assessment in complex terrain: The case of COSMO-1 in the Swiss Alps, Front. Energy Res., [doi:10.3389/fenrg.2018.00102] (https://doi.org/10.3389/fenrg.2018.00102)_

mountain-wind-potential

display_name: mountain-wind-potential

topography

display_name: topography

wind-energy

display_name: wind-energy

envidat

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: Dataset on Cosmo-1 based Energy Potential in Swiss Alps


en: mass-flux large-eddy-simulations eddy-covariance-measurements micro-rain-radar meteorological-data drifting-snow blowing-snow turbulence antarctica

en: Measurement data from micro-meteorological station

en: Automatic in-situ measurements of micro-meteorology and snow transport

en: Simulation data for a situation with significant snow transport

en: Data from two LES-LSM simulations called Drift_1 and Drift_2, which reproduce the conditions observed at the S17 site on 11th January 2019, 00:40 to 00:50 UTC.

en: Measurement data from snow particle counter at MRR site

en: Near-surface observations of drifting snow from a Snow Particle Counter (SPC) installed at the location of the Micro Rain Radar.

en: Simulation data for a situation with negligible snow transport

en: Results from two LES-LSM simulations called NoDrift_1 and NoDrift_2, which reproduce the conditions observed at the S17 site on 12th January 2019, 05:40 to 05:50 UTC.

en: Source code of the large-eddy simulations coupled with a Lagrangian stochastic model (LES-LSM), available on GitLab.

en: Measurement data from Micro Rain Radar (MRR)

en: Remote sensing data of blowing snow from a Micro Rain Radar (MRR).

en: Readme

en: Meta data

en:
This dataset contains measurement and simulation data. The measurements characterize the standard meteorology, turbulence, and snow transport at the S17 site near Syowa Station in East Antarctica during an expedition in austral summer 2018/2019. Large-eddy simulations with sublimating particles provide additional insight into the latent and sensible heat exchange between snow and air in two example situations observed at the S17 site.

A part of the measurement data was recorded by an automatic measurement station from 10th January 2019 to 26th January 2019. This measurement station was equipped with standard meteorological sensors, a three-dimensional ultrasonic anemometer, an open-path infrared gas analyzer, a snow particle counter, an infrared radiometer for measurements of the surface temperature, and a sonic ranging sensor measuring changes in snow surface elevation.

At a horizontal distance of approximately 500 m, a Micro Rain Radar (MRR) was installed in a tilted configuration with an elevation angle of 7° for remote sensing of blowing snow between 25th December 2018 and 24th January 2019. In addition, near-surface in-situ measurements of snow transport were performed at the location of the MRR by deploying a snow particle counter from 27th December 2018 to 24th January 2019.

The simulations cover a 18 x 18 x 6 m³ domain and reproduce the steady-state conditions during a 10-min interval with significant snow transport and another 10-min interval with negligible snow transport. We provide the model source code and the post-processed simulation data, i.e., horizontally averaged quantities as a function of height and time.

antarctica

display_name: antarctica

blowing-snow

display_name: blowing-snow

drifting-snow

display_name: drifting-snow

eddy-covariance-measurements

display_name: eddy-covariance-measurements

large-eddy-simulations

display_name: large-eddy-simulations

mass-flux

display_name: mass-flux

meteorological-data

display_name: meteorological-data

micro-rain-radar

display_name: micro-rain-radar

turbulence

display_name: turbulence

en: Meteorology and snow transport at S17 near Syowa, Antarctica, in austral summer 2018/2019


en: outgoing weissfluhjoch shortwave-radiation incoming longwave-radiation

en: DATA ACCESS

en: Metadata

en: Processing doc

en: Parameter file

en:
Corrected incoming and outgoing shortwave and longwave 2 min radiation measurements at the Weissfluhjoch summit, Davos, CH.

 References
1. Marty, C., Philipona, R., Frohlich, C., Ohmura, A.. Altitude dependence of surface radiation fluxes and cloud forcing in the alps: results from the alpine surface radiation budget network. 2002. Theoretical and Applied Climatology. Volume 72. Issue 3-4. 137-155. http://dx.doi.org/10.1007/s007040200019. 10.1007/s007040200019.
2. Christoph Marty. Surface Radiation, Cloud Forcing and Greenhouse Effect in the Alps. 2000. Institute fuer Klimaforschung ETH. Zuercher Klima-Schriften. Volume 79. http://e-collection.library.ethz.ch/eserv/eth:23491/eth-23491-01.pdf.

incoming

display_name: incoming

longwave-radiation

display_name: longwave-radiation

outgoing

display_name: outgoing

shortwave-radiation

display_name: shortwave-radiation

weissfluhjoch

display_name: weissfluhjoch

educ

en: Education, culture and sport

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: ASRB_WFJ: Shortwave and longwave radiation measurements (2 min) at the Weissfluhjoch research site, Davos


en: endemism madagascar flora landscape-evolution geology

en: Data v1.o

en: used for paper submission only

en: Escarpment evolution drives the diversification of the Madagascar flora

en: This upload contains the data (species checklist, species range maps, time-calibrated phylogenies, topographic change, etc.) generated, analyzed, and presented in the paper .

en: Although much of the endemic biodiversity of Madagascar can be attributed to its isolation as an island in the Indian Ocean, the high rates of speciation throughout its geologic history suggest an influence of local-scale landscape dynamics. The topographic evolution of Madagascar is dominated by the formation of high-relief continental rift escarpment and we argue that the erosion and landward retreat of this topography creates habitat heterogeneity that has served as a speciation pump for the island. The highest plant richness is found along the escarpment and is characterized by steady diversification rates over the last 45 Ma. Modeled landscape evolution by escarpment retreat demonstrates opportunities for allopatric speciation by transient habitat fragmentation through multiple mechanisms, including catchment expansion, isolation of highland remnants and formation of topographic and river barriers The segregation of floral phylogenetic turnover parallel to the escarpment is consistent with these mechanisms and indicates the importance of erosion-driven landscape dynamics on speciation.

endemism

display_name: endemism

flora

display_name: flora

geology

display_name: geology

landscape-evolution

display_name: landscape-evolution

madagascar

display_name: madagascar


aerosol-data-weissfluhjoch

title_for_slug: aerosol-data-weissfluhjoch

en: inp aerosol particles ice-nucleation linda raclets

en: LINDA Dataset Weissfluhjoch

en: The LINDA file contains information on temperature (in °C) dependent frozen fractions, number of Ice Nuleating Particles (INP, per standard liter) and differential INP concentrations (per standard liter and Kelvin).

en: SMPS Dataset Weissfluhjoch

en: The SMPS file contains aerosol data (particle concentration, total number concentration, median, mean, geometric mean, mode and geometric standard deviation of the size distribution) in a size range between 12 and 460 nm (electrical mobility diameter) as well as instrument characteristics (sample temperature, pressure, relative humidity, mean free path and gas viscosity) in a temporal resolution of 2 minutes, with time in UTC, measured at Weissfluhjoch.

mimetype: application/x-netcdf

en: OPC-N3 Dataset Weissfluhjoch

en: Particle concentrations in a size range of 0.35 μm to 40 μm were measured with an OPC-N3 (Alphasense, Inc.) in a resolution of 20 seconds (time in UTC). PM₁, PM₂,₅ and PM₁₀ were directly derived.

en: OPC-GT526S Dataset Weissfluhjoch

en: Particle counts were recorded in six size channels (0.3, 0.5, 0.8, 1.5, 2.5 and 5 μm) in a resolution of 20 seconds (time in UTC) by a particle counter (GT-526S, Met One Instruments, Inc.).

en: APS Dataset Weissfluhjoch

en: The APS file contains aerosol data (total number concentration, median, mean, geometric mean, mode and geometric standard deviation of the size distribution) for aerodynamic diameters between 0.5 μm and ~20 μm as well as instrument characteristics, in a temporal resolution of 20 seconds, with time in UTC, measured at Weissfluhjoch.

en:
Aerosol properties were measured between February 8 and March 31 2019 at the measurement site Weissfluhjoch (LON: 9.806475, LAT: 46.832964). Optical and aerodynamic particle counters, as well as a scanning mobility particle size spectrometer and an ice nuclei counter were deployed to report particle concentrations and size distributions in fine (10-1000 nm) and coarse mode (> 1000 nm), cloud condensation nuclei concentrations (CCNCs), and ice nuclei particle concentrations (ICNCs). The ambient particles were transported via a heated inlet to be distributed to the particle detecting devices inside the setup room.

Optical Particle Counter (OPC): Light scattering of a diode laser beam caused by travelling particles is used in the both, the OPC-N3 (0.41 - 38.5 μm) and GT-526S (0.3 – 5 μm), to determine their size and number concentration. For the OPC-N3, particle size spectra and concentration data are used afterwards to calculate PM₁, PM₂,₅ and PM₁₀ (assumptions: particle density: 1.65 g cmˉ³, refractive index: 1.5+i0).

Aerodynamic Particle Sizer (APS): The APS (3321, TSI Inc.) measured the particle size distribution for aerodynamic diameters between 0.5 μm and ~20 μm by the particle’s time-of-flight and light-scattering intensity (assumptions: particle density 1 g cmˉ³).

Scanning Mobility Particle Size Spectrometer (SMPS): Particle number concentrations in a size range between 12 and 460 nm (electrical mobility diameter) were measured at Davos Wolfgang, using a Scanning Mobility Particle Sizer Spectrometer (SMPS 3938, TSI Inc.). The classifier (3082, TSI Inc.) was equipped with a neutralizer (3088, TSI Inc.) and a differential mobility analyzer working with negative polarity (3081, TSI Inc.). The size selected particles were counted by a water-based condensation particle counter (3787 TSI Inc.). The TSI AIM software was used to provide particle size distributions by applying multiple charge and diffusion loss corrections (assumptions: particle density 1 g cmˉ³).

Coriolis μ and LINDA: A microbial air sampler (Coriolis μ, bertin Instruments) was used to collect airborne particles for investigating their ice nucleating ability with a droplet freezing device. Particles larger than 0.5 μm were drawn with an air flow rate of up to 300 l min‾¹ into the cone and centrifuged into the wall of the cone due to the forming vortex. The liquid sample was transferred into the LED based Ice Nucleation Detection Apparatus (LINDA, University of Basel) to study heterogeneous ice formation (immersion freezing mode) of ambient airborne particles.

aerosol

display_name: aerosol

ice-nucleation

display_name: ice-nucleation

inp

display_name: inp

linda

display_name: linda

particles

display_name: particles

raclets

display_name: raclets

en: Aerosol Data Weissfluhjoch


en: borehole ritigraben permafrost permos ground-temperature

en: PERMOS DATA POLICY

en: Map of PERMOS borehole network

en: DATA ACCESS

en:
_ENVIDAT NOTE: Data currently unvailable and measures are being taken to recover and restore the data files._

Processed ground temperature measurements at the Ritigraben permafrost borehole (RIT_0102) in canton Valais, Switzerland. The borehole is located at 2690 m asl on a flat site. The surface material is coarse blocks and borehole depth is 30 m. Thermistors used YSI 44006. Year of drilling 2002. This borehole is part of the Swiss Permafrost network, PERMOS (www.permos.ch). Contact phillips@slf.ch for details of processing applied.

borehole

display_name: borehole

ground-temperature

display_name: ground-temperature

permafrost

display_name: permafrost

permos

display_name: permos

ritigraben

display_name: ritigraben

educ

en: Education, culture and sport

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: RIT1: Processed permafrost borehole data (2690  m asl), Ritigraben, Switzerland


en: meteorology precipitation climate-change wind-speed par long-term swiss-forest-lab meteo temperature relative-humidity

en: Site photo of the field station (VOF)

en: Site photo of the field stationfrom the side.

en: Field station data (VOF)

en: Data file.

en: Data plot of the field station (VOF)

en: Data overview for air temperature, relative humidity, precipitation, PAR, wind speed.

en: Forest station data (VOB)

en: Data plot of the forest station (VOB)

en: Site photo of the forest station (VOB)

en: Site photo of the forest station from the side.

en: Site aerial photo (Vordemwald)

en: Site aerial photo from both Vordemwald stations. Source: Google. 2016. Site aerial photo from both Vordemwald stations. Retrieved November 11, 2016, from https://www.google.ch/maps

en: High quality meteorological data are needed for long-term forest ecosystem research, particularly in the light of global change. The long-term data series published here comprises almost 20 years of measurements for two meteorological stations in Vordemwald in Switzerland where one station is located within a natural mixed forest stand (VOB) with European silver fir (_Abies alba_; 110 yrs) and oak trees (_Quercus sp._; 190-210 yrs) as dominant tree species. A second station is situated in the very vicinity outside of the forest (field station, VOF). The meteorological time series are presented in hourly time resolution of air temperature, relative humidity, precipitation, photosynthetically active radiation (PAR) and wind speed. Vordemwald is part of the Long-term Forest Ecosystem Research Programme (LWF) established and maintained by the Swiss Federal Research Institute WSL.

climate-change

display_name: climate-change

long-term

display_name: long-term

meteo

display_name: meteo

meteorology

display_name: meteorology

par

display_name: par

precipitation

display_name: precipitation

relative-humidity

display_name: relative-humidity

swiss-forest-lab

display_name: swiss-forest-lab

temperature

display_name: temperature

wind-speed

display_name: wind-speed

en: Vordemwald, Switzerland: Long-term forest meteorological data from the Long-term Forest Ecosystem Research Programme (LWF), from 1996 onwards


causal-effect-of-lup

title_for_slug: causal-effect-of-lup

en: annual-effect plan-evaluation psm-did land-use-change land-use-planning

en: causal-effect-of-lup

en:
Data.dbf contains the varibles of 1662 villages in Zhangzhou Cities
PSM_DID.R can re-produce the results

en:
Title: Does zoning contain built-up land expansion? Causal evidence from Zhangzhou City, China.

Research objective: Built-up land zoning is an imporatant policy measure of land use planning (LUP) to contain built-up land expansion in China. We used a difference-indifference model with propensity score matching to estimate the average and annual effect of built-up land zoning on built-up land expansion in Zhangzhou City, China between 2010 and 2020.

Data: Data.dbf contains the varibles of 1662 villages in Zhangzhou Cities in 1995, 2000, 2005, 2010, 2013, 2015, 2018, and 2020.
XZQDM2 is villages' unique administrative ID;
Area is the land area of village i;
Dis2water is the Euclidean distance from village i to the nearest waterbody;
Dis2coastl is the Euclidean distance from village i to the nearest coastline;
Dis2city is the the Euclidean distance from village i to the city center;
Dis2county is the the Euclidean distance from village i to the nearest county center;
Elevation is the the average elevation within village i;
Dis2road is the the Euclidean distance from village i to the nearest road;
Nei_Built_ is the the area of built-up land (Nei Built.upit) in the neighboring villages of village i in year t;
Treated is a binary variable, Treated = 1 to the villages that were partially or entirely located inside the development-permitted zones, and Treated = 0 to the villages that were entirely located outside the development-permitted zones;
Intensity is the percentage of land that was assigned to the development-permitted zones in village i;
Year represent the year in 1995, 2000, 2005, 2010, 2013, 2015, 2018, and 2020;
BuLE is the dependent variable, representing built-up land expansion in village i in year t;
Town is town' unique administrative ID.

Method: First, we employed propensity score matching to overcome the selection bias and satisfy the parallel trend
assumption. Second, we built four Difference-in-Difference models to estimate the average and annual effect.

annual-effect

display_name: annual-effect

land-use-change

display_name: land-use-change

land-use-planning

display_name: land-use-planning

plan-evaluation

display_name: plan-evaluation

psm-did

display_name: psm-did

educ

en: Education, culture and sport

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: Causal effect of LUP


maintainer: Virginie Marques

en: environmental-dna biodiversity marine plankton fjord dna-metabarcoding fish

en: Code, data and figures

en: Here there are all the data and code to reproduce the figures and analysis presented in the paper, with a README.md file

en: Metabarcoding data

en: Raw metabarcoding data for both primers (teleo and 18S) and corresponding file to perform the demultiplexing and primer trimming

en:
This dataset contains the raw environmental DNA data associated with the publication *Environmental drivers of eukaryotic plankton and fish biodiversity in an Arctic fjord* in the journal Polar Biology (2023).

 Methods

**Sampling**
We sampled the Lilliehöök fjord on the west coast of Spitsbergen (Svalbard, Norway) over 3 days from 3 to 5 of August 2021. Samples were taken from the glacier front up to the fjord mouth of the Krossfjorden system, around 30 km long, after the Lilliehöök fjord merged with the mouth of Möller fjord. The fjord’s maximum depth has been recorded at 373 m (Svendsen et al. 2002) and has no sill at its entrance, thereby facilitating water exchange with the open ocean of the West Spitsbergen Current. We used a research vessel to sample 5 sites for a total of 15 samples, sampling 3 depths per site (3-m, chlorophyll a maximum and 85-m, unless sea floor was shallower). Shallow and intermediate samples between 3-m and 12-m represent ~35-L of water filtered in-situ using long tubing and a peristaltic pump, and all other deeper samples were taken from a total of 3 Niskin bottles (General Oceanics), representing 22-L of water sampled per sample. Water was filtered through a VigiDNA filtration capsule (SPYGEN) with a 0.20-µm pore size using an Athena peristaltic pump (Proactive Environmental Products, Bradenton, Florida) with a flow rate of ~1-L/min. Each sample was handled with single use tubing and gloves.

**Molecular**
To perform the amplification, we used two sets of primers: teleo (forward: ACACCGCCCGTCACTCT, reverse: CTTCCGGTACACTTACCATG; Valentini et al. 2016) and the universal eukaryotic 1389F/1510R primer pair, amplifying the V9-18S rDNA gene (Amaral-Zettler et al. 2009) (forward: TTGTACACACCGCCC, reverse: CCTTCYGCAGGTTCACCTAC).

 Data content:

+ Metabarcoding data: This zip file contains the 2 sequencing libraries filtered to only retain the samples used in the present study.
+ Code, data and figure: This zip file contains all data and code to reproduce the figures and the analysis in the study, with an associated README explaining the content of each folder.

 Additional informations
For more details, please see the Methods in the associated publication: DOI: 10.1007/s00300-023-03187-9.

biodiversity

display_name: biodiversity

dna-metabarcoding

display_name: dna-metabarcoding

environmental-dna

display_name: environmental-dna

fish

display_name: fish

fjord

display_name: fjord

marine

display_name: marine

plankton

display_name: plankton

en: Data: Environmental drivers of eukaryotic plankton and fish biodiversity in an Arctic fjord


en: meteorology temperature precipitation climate-change par long-term wind-speed meteo swiss-forest-lab relative-humidity

en: Data plot of the forest station (LEB)

en: Data overview for air temperature, relative humidity, precipitation, PAR, wind speed.

en: Forest station data (LEB)

en: Data file.

en: Site photo of the forest station (LEB)

en: Site photo of the forest station from below (viewing upwards the slope)

en: High quality meteorological data are needed for long-term forest ecosystem research, particularly in the light of global change. The long-term data series published here comprises almost 20 years of measurements for one meteorological station in Lens in Switzerland which is located within a natural coniferous forest with Scots pine (_Pinus sylvestris_; 150-170 yrs)) as dominant tree species. The meteorological time series are presented in hourly time resolution of air temperature, relative humidity, precipitation, photosynthetically active radiation (PAR) and wind speed. Lens is part of the Long-term Forest Ecosystem Research Programme (LWF) established and maintained by the Swiss Federal Research Institute WSL.

climate-change

display_name: climate-change

long-term

display_name: long-term

meteo

display_name: meteo

meteorology

display_name: meteorology

par

display_name: par

precipitation

display_name: precipitation

en: Lens, Switzerland: Long-term forest meteorological data from the Long-term Forest Ecosystem Research Programme (LWF), from 1997 onwards


maintainer: Felix Neff

en: topsoil-removal insects diversity restoration functional-diversity long-term-experiment grassland functional-traits

en: Plot information

en:
Information on the experimental plots.

- **Plot**: ID of Plot
- **Treatment**: Experimental treatment
- **Landuse_history**: recent agricultural use for Initial; agricultural use before restoration for all restored sites
- **Last_tilled**: Last time the site was tilled
- **Intensity**: Frequency and intensity of mowing and manuring (*intensity1*: mowing once and no manure, i*ntensity2*: 2-3 times mowing and no manure, *intensity3*: 2-3 times mowing and manuring, *intensity4*: 4-5 times mowing and manuring)
- **Slope**: slope gradient according to classes defined by FAO (1990)
- **X**: X coordinate of the plot (CH1903)
- **Y**: Y coordinate of the plot (CH1903)
- **Cluster**: Spatial cluster of the plot

en: Insect abundance

en:
Abundance of adult insects recorded in the samplings on all experimental sites

- **Plot**: ID of Plot
- **Treatment**: Experimental treatment
- **Species**: Insect species name (following [Fauna Europaea](https://fauna-eu.org))
- **Author**: Author and year of species' description (following [Fauna Europaea](https://fauna-eu.org))
- **Group**: Insect group as used in the analyses
- **Number_Adults**: Number of adult individuals recorded
- **Herbivore**: Logical indicating whether the species is feeding as a herbivore (*TRUE*) or not (*FALSE*)

en: Insect traits

en:
Functional traits of all herbivorous insect species sampled in the study.

- **Species**: Insect species name (following [Fauna Europaea](https://fauna-eu.org))
- **Author**: Author and year of species' description (following [Fauna Europaea](https://fauna-eu.org))
- **Group**: Insect group as used in the analyses
- **Body volume**: Body volume determined by body length, body width and body height (in mm$^3$)
- **Body_shape**: Ratio of body length to body width
- **Hind_femur_shape**: Ratio of hind-femur length to hind-femur width
- **Hind_front_leg_ratio**: Ratio of front-leg length to hind-leg length (leg length = femur length + tibia length)
- **Wing_length_rel**: Ratio of wing length to body length
- **Leg_length_rel**: Ratio of front-leg length to body length (leg length = femur length + tibia length)
- **Antenna_length_rel**: Ratio antenna length to body length
- **Eye_width_rel**: Ratio of eye width to head width (Auchenorrhyncha, Heteroptera) / to head height (Orthoptera)
- **Feeding_specialization**: Insect specialization on food source (*m*: monophagous, *o*: oligophagous, *p*: polyphagous)
- **Feeding_tissue**: Feeding tissue used for feeding (*c*: chewers, *x*: xylem, *p*: phloem, *m*: mesophyll, *m-p/r*: mesophyll as well as phloem and/or reproductive organs, *r*: reproductive organs, *se*: ripe seeds)
- **Hibernation**: Hibernation stage (*e*: egg, *e/n*: egg and nymph, *n*: nymph, *a*: adult)
- **Generations**: Number of generations per year (*1.5* stands for *1-2* generations per year)
- **Moisture_pref_mean**: mean of preferred habitat moistures (*1*: xerophilous, *2*: moderately xerophilous, *3*: moderately mesohygrophilous, *4*: mesohygrophilous, *5*: moderately hygrophilous, *6*: hygrophilous, *7*: moderately hydrophilous, *8*: hydrophilous)
- **Moisture_pref_range**: range of preferred habitat moistures (indicating degree of specialization)

en:
This dataset contains all data, on which the following publication below is based.

**Paper Citation**:

Neff, F., Resch, M. C., Marty, A., Rolley, J. D., Schütz, M., Risch, A. C, Gossner, M. M. 2020. Long-term restoration success of insect herbivore communities in semi-natural grasslands: a functional approach. Ecological Applications, 30, e02133. [10.1002/eap.2133](https://doi.org/10.1002/eap.2133)

Please cite this paper together with the citation for the datafile.

 Methods

 Study site
The study area is situated within and nearby to Eigental nature reserve (47°27’36” to 47°29’06” N, 8°37’12” to 8°37’44” E, 461 to 507 m a.s.l.) in the vicinity of Zurich airport (Canton Zurich, Switzerland). Mean annual precipitation and temperature is 903 ± 136 mm and 9.14°C ± 0.50°C (mean ± SD for 2007-2017 (*MeteoSchweiz 2018*)). In 1967, the Eigental nature reserve was established to protect small and isolated remnants of species-rich, semi-natural grasslands (roughly 12 ha), which were embedded in an otherwise intensively managed landscape. It is characterized by oligo- to mesotrophic Molinion (semi-wet, matrix species *Molinia caerulea*) and Mesobromion (semi-dry, matrix species *Bromus erectus*) meadows (*Delarze et al. 2015*), reflecting small-scale habitat heterogeneity, mainly due to site-specific groundwater levels and slope inclination. As in most Central European grasslands, management is necessary to prevent shrub and tree invasions as well as to secure low levels of available soil nutrients and thus to maintain these species-rich habitats ([*Poschlod and WallisDeVries 2002*](https://doi.org/10.1016/S0006-3207(01)00201-4)).
In 1990, the government of the Canton Zurich decided to enlarge the Eigental nature reserve as a counter measure against degradation and biodiversity loss in semi-natural grasslands due to overutilization and the excessive input of nutrients (mostly nitrogen). Eleven patches of adjacent intensively managed grassland (in total roughly 20 ha) were targeted to be transformed into semi-natural grasslands. As a first restoration measure, fertilization was ceased, and biomass harvested three times to remove excessive soil nutrients from the original system and thus benefit plant species with low competitive ability on the long run. In 1995, the restoration efforts were increased and a large-scale experiment comprising three restoration measures with increasing intervention intensities was implemented:

- **Harvest only**: Initial restoration measures were continued with mowing and removing of the aboveground biomass two times a year (early summer and autumn).
- **Topsoil**: Removal of topsoil, depending on the thickness of the A horizon the upper 10 to 20 cm, in four randomly selected areas within the eleven patches in late autumn 1995. The size of the restoration area depended on individual patch size (2700 to 7000 m2).
- **Topsoil + Propagules**: Plant propagules were added on half of the area where topsoil was removed via application of fresh, seed-containing hay and hand-collected propagules of target species originating from semi-dry and semi-wet species-rich grasslands with local and regional provenance (within radius of 7 to 30 km) (1995, 1996, 1997).

Management of *Topsoil* and *Topsoil + Propagules* started five years after treatment implementation and included yearly mowing and removing of aboveground biomass (late summer or early autumn). The experiment was complemented with intensively managed grassland sites that share the same agricultural history as the restored sites (**Initial**; swards dominated by *Lolium perenne*, *L. multiflorum* and *Trifolium repens*): mowing and subsequent fertilizing (manure) up to five times a year, as well as different tillage regimes. Finally, sites were selected in target semi-dry and semi-wet grasslands (**Target**) located within the Eigental nature reserve and another nature reserve nearby (Altläufe der Glatt; 47°28’29” to 47°27’41” N, 8°31’56” to 8°32’26” E, 418 to 420 m a.s.l.). The selected target sites are mown and aboveground biomass removed once a year in late summer or early autumn. For each of the five treatments, we selected eleven plots (5 m × 5 m) spread across the sites. Altogether, the experiment included 55 plots.

 Arthropod sampling
Aboveground arthropods were sampled using suction sampling on four consecutive days in early July 2017 before the grasslands were mown. Arthropods were sampled in two locations on each 5 m × 5 m plot, once in the south-western and once in the north-eastern corner to account for possible spatial heterogeneity within the plots. Arthropods were sorted to order or lower taxonomic levels and individuals were identified to species level. We focused on three groups (Hemiptera: Auchenorrhyncha, Hemiptera: Heteroptera, Orthoptera),

 Functional traits
We used two sets of functional traits in this study.

**Morphometric traits**:
Body volume, body shape, hind femur shape, hind/front leg ratio, wing length, leg length, antenna length and eye width. We used trait measurements from [*Simons et al. (2016)*](http://dx.doi.org/10.1890/15-0616.1) and [*Neff et al. (2019)*](https://doi.org/10.1007/s10980-019-00872-1) and complemented them with measurements on study specimens. These measurements were conducted using a high-resolution measuring stereo microscope (Leica DVM6, Leica Microsystems) including automated high-resolution photo stacking with the software Leica Application Suite X (LAS X, © 2018 Leica Microsystems CMS GmbH) and Leica Map Premium (Leica Microsystems, © 1996-2017 Digital Surf) at WSL Birmensdorf. The eight morphometric traits were calculated from direct measurements of body parts on specimens of all sampled species. From each species, we measured at least one female and one male specimen. Additionally, for species that show wing dimorphism, we included the different wing morphs and weighted them by their prevalence reported in literature. For few species, of which not all wing morphs were available for measurements (10 cases), we estimated relative wing length from congeneric species or from the literature.

**Life-history traits**
Based on an existing data set collected by [*Gossner et al. (2015)*](http://dx.doi.org/10.1890/14-2159.1). We included traits describing different life-history characteristics of herbivore insect species, namely: feeding specialization, feeding tissue, hibernation stage and number of generations per year, which are related to insect species’ vulnerability to changes in plant community composition, microhabitat use and disturbance tolerance. To represent potential changes in habitat moisture with abandonment of intensive land use (e.g., change in ground-water level), we also included two traits related to preferred habitat moisture of the study species: moisture preference, describing species’ optimum habitat moisture, and moisture range, which describes the species’ range of preferable moisture conditions.

 References

Delarze, R., Y. Gonseth, S. Eggenberg, and M. Vust. 2015. Lebensräume der Schweiz: Ökologie - Gefährdung - Kennarten. 3rd ed. Ott, Bern.

Gossner, M. M., N. K. Simons, R. Achtziger, T. Blick, W. H. O. Dorow, F. Dziock, F. Köhler, W. Rabitsch, and W. W. Weisser. 2015. A summary of eight traits of Coleoptera, Hemiptera, Orthoptera and Araneae, occurring in grasslands in Germany. Scientific Data 2:150013.

MeteoSchweiz. 2018. Klimabulletin Jahr 2017. MeteoSchweiz, Zürich.

Neff, F., N. Blüthgen, M. N. Chisté, N. K. Simons, J. Steckel, W. W. Weisser, C. Westphal, L. Pellissier, and M. M. Gossner. 2019. Cross-scale effects of land use on the functional composition of herbivorous insect communities. Landscape Ecology 34:2001–2015.

Poschlod, P., and M. F. WallisDeVries. 2002. The historical and socioeconomic perspective of calcareous grasslands—lessons from the distant and recent past. Biological Conservation 104:361–376.

Simons, N. K., W. W. Weisser, and M. M. Gossner. 2016. Multi-taxa approach shows consistent shifts in arthropod functional traits along grassland land-use intensity gradient. Ecology 97:754–764.

diversity

display_name: diversity

functional-diversity

display_name: functional-diversity

functional-traits

display_name: functional-traits

grassland

display_name: grassland

insects

display_name: insects

long-term-experiment

display_name: long-term-experiment

restoration

display_name: restoration

topsoil-removal

display_name: topsoil-removal

educ

en: Education, culture and sport

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: Grassland restoration: insects and insect traits