en: modeling land-use-change land-use landscape-services statistical-model switzerland urbanization

en: Scripts for Assessing potential landscape service trade-offs driven by urbanization in Switzerland

en:
Scripts ordered by their main purpose within sequential folders in this ReadMe marked with

Within the folders the capital letters refer to the parallel or sequential use of the scripts; scripts here in ReadMe are marked with

 00_Function Scripts
 Functions.r
Script containing several functions for analyzing statistical models: cohen.kappa, meva.table, D2, max-Tss, plot-TSS

 Service_functions.R
Script containing functions for calculating all services and returning sums (and median for bd and rec) as well as rasters

 01_Data Preparation
 A_AS_raster_preparation.R
Preparation of the land use rasters for the years 1985, 1997, and 2009 based on the original Arealstatistik (AS/ASCH); Assigning our categories and assining new values to all "construction sites" for calibrating the models
For model projection starting point (2009) and for service calculations (all ASCH years) the "other" categories were assigned to the land use categories based on dominant neighbor, so that there were no empty cells
Creation of water & mountainous area raster that stayed stable throughout the projections
Creation of MFH raster (2009), to have as base for all new projection years, as this category never becames any other

 B_Factors_preparation.R
Preparation of the factor rasters that were used to calculate service values per cell (see Table 2): LWfactor, Transportation, Vol, Rivers, Lakes, slope, TWW, Hazard_risk

 B_Predictors_preparation.R
Preparation of the raster of the predictors used for calibrating (ASCH years) and projecting (stable) the transition models that do not depend on the land use categories: Temperature (ASCH years), solar radiation (stable), Public transportation access (stable), Elevation (stable), Workers density (ASCH years), Population change (ASCH transitions)

 B_Regions_preparation.R
Preparation of bioregions as raster to be used to mask asxxxx later to calculated services and land use area just for one region

 C_Pred_proj.R
Projecting the dynamic predictors into the future for projecting the land use transitions with the model: Linear extrapolations for workers densities and population; more detailed extrapolation of temperature (based on data for all stations that matched between the temp table we used for the calibration period and the projections from CS2M, and then making a spatial interpolation for all years based on the interpolation of temperature for all years per station)

 02_Model calibration
 A_Bioreg_pred_corr.R
Calculating correlation between the predictors for each bioregion and land use category, Output are those with too high correlation so that one predictor can be removed from transitions were both predictors occur

 A_trans_numbers_bioreg.R
Calculate transition numbers for each bioregion to decide which transitions to primarily consider

 B_Bioreg_ext_eval.R
Calculating TSS based on the external evaluation for the bioregion transitions that happened often enough to try to model them (calibration data: 85-97, evaluation data: 97-09)

 B_Bioreg_int_eval.R
Calculating TSS based on the internal evaluation for the bioregion transitions that happened often enough to try to model them (calibration data: 70%, evaluation data: 30%)

 C_Bioreg_TSS_analysis.R
Extracting TSS numbers from internal and external evaluation, calculating mean and median for each transition for each region for each evaluation method and saving as csv per region to be able to select only the transitions with high enough model performance

 D_Bioreg_Models_for_prediction.R
Calibration of the models that were then used to project land use transitions into the future; calibrated separately for each bioregion

 E_Residuals_trans_models.R
Calculation of Moran's I statistics to analyze the residuals of the land use transition models

 03_Projections
 A_Bioreg_Projections_run.R
Master script for: Extrapolaitng into the future with the regional models and then assembling for each time step to calculate new AS predictors; Several Outputs: txt file to test for NAs in Predictors, txt file with random seed number for sampling, txt file with times for calculation steps (check progress of script while running), csv sheet with projected transition frequencies, tif-rasters for every region and time step, pdf with raster plot for every region and time step

 04_Service calculation
 A_Bioreg_as_services.R
Calculate services per bioregion for years 1985, 1997, 2009

 A_Service_calculation_bioregions.R
Extracting service numbers(sums) per bioregions for all projection runs and storing them in a list of matrixes to be available for further plotting; can be run for swiss wide projections or regional ones

 05_Analysis
 A_Bioreg_ASCH_development.R
Extracting the occurrence of each category per region for all runs (first part), then for ASCH years, and then plotting them nicely; only works for regional projections

 A_Bioreg_Predictors_importanceD2.R
Calculating D2 for each transition and each considered predictor from bivariate models to get value of importance

 B_Bioreg_Pred_imp_analysis.R
Using calculated D2 to sort Predictors according to their importance for each transition

 A_Bioreg_Spatial_results_analysis.R
Plotting randomly sampled runs for ASCH and services to analyses their spatial development

 A_Bioreg_Transition_numbers_check_v1.R
Analyzing the frequency for all transitions for all regions and producing the point plots for each transition separately

 A_Bioreg_Transition_numbers_check_v2.R
Analyzing percentage and numbers of all transitions but plotting them per region and originating ASCH category

 B_Transition_Analysis.R
Further Analysis of transition numbers

 A_Service_analysis.R
Plotting of the service development for bioregions in several ways for analyzing

en: Data for Assessing potential landscape service trade-offs driven by urbanization in Switzerland

en:
The provided folder structure follows the set up of the scripts.
Data is only provided when it has been fully produced by us, otherwise dummies are given.
For data that will be produced by one of the scripts, no dummies are given.
The folders may contain sub-folders, which would be filled if the scripts were all run

 00_Analysis_Data
Data produced throughout the process of the calibration and projection that is later needed for analysis

 01_Raw_Data
Primary data from external sources that were used to compile the rasters and numbers used during the calibration and projection of landscape transitions as well as service calculation

 02_Prepared_Data
Data that will be prepared for further use by scripts are put in here
Additionally it contains the parameter sheets for the transition predictors that we compiled

 03_Model_Data
 Model outputs
Folder were the projection models statistics will be saved
 Models
Folder into which the actual transition models will be saved
 Residuals
Folder into which data on models residuals will be saved for future use

 04_Projected_Data
The output of the projections will be saved into this folder

 05_Service_Data
Any service calculations will be saved in here

 06_Results_Analysis
Any Analysis plots and tables as well as intermediate data will be saved here in the respective sub-folder

en:
Data and scripts of publication:

Madleina Gerecke, Oskar Hagen, Janine Bolliger, Anna M. Hersperger, Felix Kienast, Bronwyn Price, Loïc Pellissier (2019) Assessing potential landscape service trade-offs driven by urbanization in Switzerland. Palgrave communications.

Contains land use projections for Switzerland and scripts and data for these projections as well as the calculation of landscape services.

Data Folder:
Contains sub-folder with the data necessary for this study (provided were no copyright issues, otherwise placeholders with descriptions), and folders where produced data may be stored

Scripts Folder:
Contains scripts organized into subfolders depending on their purpose

Note: Some abbreviations within the scripts and data are derived from German words and not English.

land-use

display_name: land-use

land-use-change

display_name: land-use-change

landscape-services

display_name: landscape-services

modeling

display_name: modeling

statistical-model

display_name: statistical-model

switzerland

display_name: switzerland

urbanization

display_name: urbanization

en: Land use projections and services for Switzerland


maintainer: EnviDat Support

en: cryowrf landuse antarctica topography wrf

state: active

type: dataset

en: WPSinput

media_type: application/zip

en: Input files to run the Weather Research and Forecasting model (WRF) preprocessing system WPS with REMA topography and AntarcticaLC2000 landuse data (see Documentation for details).

format: ZIP

mimetype: application/zip

en: Documentation

media_type: application/pdf

en: Documentation about how the provided dataset was produced including details to reproduce the dataset.

format: PDF

mimetype: application/pdf

en: Scripts

en: Scripts to run the preprocessing to produce WRF binary tiles from REMA and AntarcticaLC2000 for topography and landuse (see Documentation for procedure).

en:
Reference Elevation Model of Antarctica (REMA) topography and AntarcticaLC2000 landuse data
are now available as static data input for the Weather Research and Forecasting model (WRF). Topography
and landuse are made available at a spatial resolution of 1 km. This documentation describes the methods
applied to convert REMA and AntarcticaLC2000 to WRF readable format and shows how this improves
the representation of the Antarctic topography and landuse categories over coastal Antarctic regions.

antarctica

display_name: antarctica

cryowrf

display_name: cryowrf

landuse

display_name: landuse

topography

display_name: topography

wrf

display_name: wrf

educ

fr: Éducation, culture et sport

de: Bildung, Kultur und Sport

en: Education, culture and sport

it: Istruzione, cultura e sport

envidat

fr: EnviDat: le portail de données environnementales

de: EnviDat: das Umwelt-Datenportal

en: EnviDat: the Environmental Data Portal

it: EnviDat: il portale dei dati ambientali

fr: EnviDat est le portail de données du WSL; il offre un accès uniformisé et réglementé aux données de surveillance et de recherche en matière d’environnement. Ce portail est capable d’héberger et de publier des ensembles de données précieuses et uniques, qui sont partagées aux quatre coins de la planète. Ce faisant, EnviDat favorise la recherche et contribue à l’avancement des sciences environnementales.

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

de: EnviDat ist das Datenportal der WSL für einen einheitlichen und verwalteten Zugang zu Umweltdaten aus Monitoring- und Forschungsprojekten. Auf dem Portal können Datensätze gehostet und veröffentlicht werden. Durch die weltweite Bereitstellung einzigartiger und wertvoller Datensätze leistet EnviDat einen Beitrag zur Forschung im Bereich der Umweltwissenschaften.

it: EnviDat è il portale dati del WSL che fornisce un accesso unificato e gestito ai dati di monitoraggio ambientale e di ricerca. Il portale ha la capacità di ospitare e pubblicare serie di dati preziosi e unici che vengono condivisi in tutto il mondo. Così facendo, EnviDat promuove la ricerca e contribuisce al progresso della scienza ambientale.

political_level: other

wsl

capacity: public

type: organization

approval_status: approved

key: guid

key: uri

value: Envidat Harvester

en: REMA topography and AntarcticaLC2000 for WRF


maintainer: Anita C. Risch

en: herbivory native-plant weed-management non-native-plant grassland

en: Correction: Data file native and non-native plant interactions in Australian grasslands

en:
taxa tab:	list and overview of all the recorded species

* family:                 family of the plant

* genus:                genus of the plant

* species:                plant species name

* origin:                indicates whether the plant is native to Australia or not (non-native)

* common name:	        common name of the plant species

* functional group:	        functional group of the plant species: forb, graminoid, fern, tree

* functional group detailed:	gives more detail about the type of graminoid and forb: legume, forb (non-leguminous),
                        grass, sedge, rush, fern, tree

* lifeform:                annual or perennial lifeform (species which can have both of these lifeforms where
                        considered as annuals)

plot tab:	list of species found in each plot and their cover (%)

* sampling.session:        provides information about the sampling time:
                        May2020 = data that was collected in May 2020
                        Nov2020 = data that was collected in November 2020

* farm.name:	            name of the farms where the sampling took place:
                        SF = farm of the Southern group
                        NF = farm of the Northern group
                        numbers 1-3 = randomly allocated to the Southern group of farms
                        numbers 4-6 = randomly allocated to the Northern group of farms

* site.type:	                KG: Kangaroo grass dominated site
                        ALG: ALG+KG site (Kangarooo grass and African lovegrass co-dominated site)

* plot.no:                plot number: 9-12

* scientific.name:	        scientific name of the plant species found in a certain plot

* functional group:	        indicates whether the species found is a tree, forb, graminoid or fern

* functional group detailed:	indicates whether the species found is a tree, legume, forb (non-leguminous),
                        grass, sedge, rush, fern

* lifeform:                specifies the lifeform of the species: annual or perennial lifeform
                        (species which can have both of these lifeforms where considered as annuals)

corrections tab:	Detailed description of corrections made in plot.data tab

format: XLS

en:
This dataset contains all data, on which the following publication below is based.

Paper Citation:

_Schlierenzauer, C., Risch, A.C., Schütz, M., Firn, J. 2021. Non-native Eragrostis curvula reduces plant species diversity in pastures of South-eastern Australia even when native Themeda triandra remains co-dominant. Plants 10, 596._

Please cite this paper together with the citation for the datafile.

Study area
The study was conducted in the lowland grassy woodlands of the Bega Valley Region, which is located in the south-east corner of New South Wales, Australia. Embedded between the Pacific Ocean and the Australian Alps, the lowland grassy woodlands are mostly located on granitic substrates and reach elevations of roughly 500 m above sea level. Typically, these grassy woodlands receive less precipitation (mean annual precipitation between 700-1100 mm) compared to the more elevated areas that surround them (NSW Government - Office of Environment and Heritage 2017).
The vegetation is dominated by an open tree canopy layer consisting of Eucalyptus tereticornis Sm, Angophora floribunda Sm. (Sweet) and a range of other eucalypt species. Sometimes shrub or small trees are also present, whereas grasses and forbs form the ground-cover. In areas without intensive agricultural history, this layer is dominated by perennial, tussock grasses such as Themeda triandra Forssk, Microlaena stipoides R.Br (Weeping Grass), Eragrostis leptostachya Steud. (Paddock Lovegrass) and Echinopogon ovatus P.Beauv (Forest Hedgehog Grass). The remaining inter-tussock spaces are occupied by a diversity of growth-restricted grasses and herbaceous forbs (NSW - Department of Planing, Industries and Environment 2019; NSW Government - Office of Environment and Heritage 2017).
Clearing, pasture sowing, fertilizer application and livestock grazing resulted in a dramatic decrease in the extent of these natural woodlands, with less than five percent within conservation reserves and overall, with only about 20% of their original extent in New South Wales still existing (Tozer et al. 2010). The remaining areas outside of reserves are threatened by altered fire frequencies, habitat clearing, livestock grazing and especially by non-native plant invasion, particularly Eragrostis curvula (Schrad.) Nees. For this reason, the grassy woodlands are listed as an endangered ecological community in the NSW state legislation. Additionally, they are considered as critically endangered by the Commonwealth of Australia (Threatened Species Scientific Committee (TSSC) 2013).

Experimental design and sampling
The study was conducted on six farms and in each of them two sites were chosen, representing a paired design. One of the sites at each farm is dominated by native Themeda triandra, the other one co-dominated by non-native Eragrostis curvula and Themeda triandra. All farms are within a radius of approximately 10 km from the town Candelo. Three of the farms are located North (36°40’ to 36°42’ S and 149°38’ to 149°42’ E) and three of them are located South (36°51’ to 36°49’ S and 149°38’ to 149°42’ E) of Candelo.
Non-native herbivores (mainly cattle, sheep and rabbits) and native herbivorous marsupials (mainly kangaroos, wallabies and wombats) are present in the area of these sites. On each site, data was collected within four plots (each 1 x 1 m) in May and November 2020. All plant species found within a plot were recorded and their relative abundance was estimated.

References
NSW - Department of Planing, Industries and Environment. 2019. “Lowland Grassy Woodland in the South East Corner Bioregion - Endangered Ecological Community Listing.” https://www.environment.nsw.gov.au/topics/animals-and-plants/threatened-species/nsw-threatened-species-scientific-committee/determinations/final-determinations/2004-2007/lowland-grassy-woodland-south-east-corner-bioregion-endangered-ecological-community-l (February 18, 2021).
NSW Government - Office of Environment and Heritage. 2017. “Lowland Grassy Woodland in the South East Corner Bioregion - Profile.” https://www.environment.nsw.gov.au/threatenedSpeciesApp/profile.aspx?id=20070 (January 31, 2021).
Threatened Species Scientific Committee (TSSC). 2013. Environment Protection and Biodiversity Conservation Act 1999 (EPBC Act) Conservation Advice for Lowland Grassy Woodland in the South East Corner Bioregion. http://www.environment.gov.au/biodiversity/threatened/communities/pubs/82-conservation-advice.pdf.
Tozer, Mark et al. 2010. “Native Vegetation of Southeast NSW: A Revised Classification and Map for the Coast and Eastern Tablelands.” Cunninghamia : a journal of plant ecology for eastern Australia 11(3): 359–406.

grassland

display_name: grassland

herbivory

display_name: herbivory

native-plant

display_name: native-plant

non-native-plant

display_name: non-native-plant

weed-management

display_name: weed-management

en: Native and no-native plant interactions in Australian grasslands


maintainer: Marcia Phillips

en: permos temperature permafrost gemsstock borehole

en: DATASET & PLOTS

en: Data visualiser and download service provided by PERMOS.

format: SERVICE

en: PERMOS DATA POLICY

en: Map of PERMOS borehole network

en:
Processed ground temperature measurements at the Gemsstock permafrost borehole in canton Uri, Switzerland. The borehole is located at 2940 m asl on a steep (50°) North-West slope (315°). The surface material is bedrock and borehole depth is 40 m. Thermistors used YSI 44008. Year of drilling 2006. This borehole is part of the Swiss Permafrost network, PERMOS (www.permos.ch). Contact phillips@slf.ch for details of processing applied.

Publications

1. A. Haberkorn, M. Phillips, R. Kenner, H. Rhyner, M. Bavay, S.P. Galos, M. Hoelzle. Thermal regime of rock and its relation to snow cover in steep Alpine rock walls: Gemsstock, central Swiss Alps. 2015. Geografiska Annaler: Series A, Physical Geography. Volume 97. Issue 3. 579–597. http://dx.doi.org/10.1111/geoa.12101. 10.1111/geoa.12101.

2. R. Kenner, M. Phillips, C. Danioth, C. Denier, P. Thee, A. Zgraggen. Investigation of rock and ice loss in a recently deglaciated mountain rock wall using terrestrial laser scanning: Gemsstock, Swiss Alps. 2011. Cold Regions Science and Technology. Volume 67. Issue 3. 157–164. http://dx.doi.org/10.1016/j.coldregions.2011.04.006. 10.1016/j.coldregions.2011.04.006.

borehole

display_name: borehole

gemsstock

display_name: gemsstock

permafrost

display_name: permafrost

permos

display_name: permos

temperature

display_name: temperature

en: Processed permafrost borehole data (2940 m asl), Gemsstock, Switzerland


en: landslide-testsite cces pore-water pressure-perturbations tramm landslides

en: TRAMM Ruedlingen data

en: TRAMM project data from the Ruedlingen site (exp 1 + 2). Measured parameters include soil suction, water level, soil volumetric water content, rain intensity, and soil temperature.

en:
A landslide testsite dataset related to pore water pressure perturbations on the stability of unsaturated silty sand slopes leading to the initiation and propagation of the shear deformations and eventual rapid mass movements. This project was initiated and led by the Institute of Geotechnical Engineering (IGT) of the Swiss Federal Institute of Technology (ETH Zurich) and was incorporated in a Swiss national (TRAMM) and a European Union (SafeLand) multidisciplinary research project. Field site: The experimental slope is 7.5 m wide by 35 m long, located in the Swiss lowlands on an east facing slope over-looking the river Rhine, at an altitude of ~ 350 masl. Originally there were forestry covertures of circa 80%, heights of 5-20 m. Shrubs up to 1-5 m high and a free herb layer covered ~ 50% of the surface. The average gradient was determined to be from 38° to 43° with a slightly concave surface. The underlying rock consists mainly of Molasse, which is formed by alternate layers of sea deposits under the Tethys Sea (Seawater Molasse) and land deposits (Freshwater Molasse). Several augured samples, as well as an outcrop of the bedrock about 20 m above the selected field, revealed horizontal layering of fine grained sand- and marlstone at the test site. The sandstone was later proven to be highly permeable and fissured. Grain-size distributions were determined and the soil was classified as medium-low plasticity silty sand. Site instrumentation:Measurements of soil suction, groundwater level, soil volumetric water content, rain intensity and soil temperature were taken and combined with geophysical monitoring using Electrical Resistance Tomography (ERT) and investigations into subsurface flow by means of tracer experiments. Deformations were monitored during the experiment, both on the surface via photogrammetrical methods and within the soil mass, using a flexible probe equipped with strain gauges at different points and two axis inclinometers on the top and acoustic sensors. Instruments were installed mainly in three clusters at depths of 15, 30, 60, 90, 120, and 150 cm below the ground surface over the slope, including jet-fill tensiometers, TDRs, Decagon TDRs, piezometers, soil temperature sensors, deformation probes, earth pressure cells, acoustic sensors and rain gauges. A ring-net barrier (provided by Geobrugg AG) was set up at the foot of the slope to protect the road. Experiments: A sprinkling experiment was carried out in September 2008 to investigate the hydrological and mechanical response of the slope (Experiment 1), followed by a second one to trigger a landslide in March 2009 (Experiment 2).

Publications

1. Lehmann, P., F. Gambazzi, B. Suski, L. Baron, A. Askarinejad, S. M. Springman, K. Holliger, and D. Or (2013), Evolution of soil wetting patterns preceding a hydrologically induced landslide inferred from electrical resistivity survey and point measurements of volumetric water content and pore water pressure, Water Resour. Res., 49, 7992–8004, doi:[10.1002/2013WR014560](http://dx.doi.org/10.1002/2013WR014560).

2. Springman, S. M., Kienzler, P., Casini, F., & Askarinejad, A. (2009). Landslide triggering experiment in a steep forested slope in Switzerland. In 17th International Conference of Soil Mechanics and Geotechnical Engineering, Alexandria, Egypt (pp. 1698-1701). doi: [10.3233/978-1-60750-031-5-1698](http://dx.doi.org/10.3233/978-1-60750-031-5-1698)

cces

display_name: cces

landslide-testsite

display_name: landslide-testsite

landslides

display_name: landslides

pore-water

display_name: pore-water

pressure-perturbations

display_name: pressure-perturbations

tramm

display_name: tramm

en: TRAMM project Ruedlingen experimental landslide dataset, Switzerland


radiosondes

maintainer: Jörg Wieder

title_for_slug: radiosondes

en: temperature relative-humidity wind-direction pressure radiosonde holoballoon wind raclets

en: Radiosond Sounding Files

en:
The "soundings" radiosond data contains information on ambient pressure (mbar), temperature (C), relative humidity (%), wind speed (m s‾ ¹) and wind direction (true deg), and are ordered with respect to the height above ground (m AGL) with a step size of 20 m. The first line of each file idicates the geographic location and the start time (in UTC) of the ascent. If the wind speed was zero, no wind direction is given.
The zip files contain ascents on the following days:
February 10 (morning and afternoon),
February 11 (morning),
February 16 (afternoon),
February 22 (morning),
March 1 (morning),
March 5 (morning),
March 11 (morning),
March 12 (morning),
March 13 (morning),
March 14 (morning),
March 17 (afternoon), and
March 18.
The data was managed with Windsond Receiver Application Demo Version 2.92, (C) Sparv Embedded AB 2016.

en: Radiosond Template Files

en:
The "template" files contain standard parameters, i.e. ambient pressure (mbar and Pa), temperature (°C), relative humidity (%), wind speed (m s‾ ¹) and wind direction (true deg), as well as additional information, e.g. time (UTC and local time), dew point (°C), mixing ration (g/kg), density (kg m³), altitude (m MSL), height above ground (ft and m AGL), and geographic coordinates (longitude, latitude). If the wind speed was zero, no wind direction is given.
The zip files contain ascents on the following days:
February 10 (morning and afternoon),
February 11 (morning),
February 16 (afternoon),
February 22 (morning),
March 1 (morning),
March 5 (morning),
March 11 (morning),
March 12 (morning),
March 13 (morning),
March 14 (morning),
March 17 (afternoon), and
March 18.
The data was managed with Windsond Receiver Application Demo Version 2.92, (C) Sparv Embedded AB 2016.

en: Radiosondes (Windsond, Sparv Embedded AB) were started in Davos Wolfgang (LON: 9.853594, LAT: 46.835577) to report height profiles of pressure, relative humidity and temperature at specific days. In addition to regular launches of radiosondes, sondes were attached to [HoloBalloon](https://www.envidat.ch/group/clouds-in-situ-raclets) to report the ambient conditions of the in-situ measurements. Further profiles of meteorological measures were recorded at [HoloGondel](https://www.envidat.ch/group/clouds-in-situ-raclets) which was installed at the gondola moving between Gotschnaboden and Gotschnagrat at 2285 m a.s.l.

holoballoon

display_name: holoballoon

pressure

display_name: pressure

raclets

display_name: raclets

radiosonde

display_name: radiosonde

relative-humidity

display_name: relative-humidity

wind

display_name: wind

wind-direction

display_name: wind-direction

educ

en: Education, culture and sport

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: Radiosondes


en: rain-on-snow natural-climate-variability cryosphere snow-water-equivalent uncertainty climate-change-impact

en: climate realizations

en: The dataset contains for three variables (snow water equivalent, surface water input and liquid precipitation) 50 realizations of current and future climate periods for two time horizons (mid end end of century), two emission senarions (RCP 4.5 and 8.5) and 10 climate model chains (all EUR11 chains within CH2018). To quantify natural climate variability for projections of snow conditions and resulting rain-on-snow (ROS) flood events, a weather generator was applied to simulate inherently consistent climate variables for multiple realizations of current and future climates at 100 m spatial and hourly temporal resolution over a 12 x 12 km high-altitude study area in the Swiss Alps. The output of the weather generator was used as input for subsequent simulations with an energy balance snow model. The data was extracted in 2021 from original model output.

climate-change-impact

display_name: climate-change-impact

cryosphere

display_name: cryosphere

natural-climate-variability

display_name: natural-climate-variability

rain-on-snow

display_name: rain-on-snow

snow-water-equivalent

display_name: snow-water-equivalent

uncertainty

display_name: uncertainty

en: Multiple realizations of daily snow water equivalent, surface water input and liquid precipitation projections for mid- and late-century


snow-drift-station-flowcapt

maintainer: Benjamin Walter

title_for_slug: snow-drift-station-flowcapt

en: wind-speed snow-blowing snowdrift flowcapt raclets acoustic-mass-flux

en: maximum mass flux

en: The data file contains the maximum mass flux of 10 minute intervalls. The duration of one cycle was 1 min and contained 6s observations and 54 s stand-by. The time is given in UTC+1.

en: minimum mass flux

en: The data file contains the minimum mass flux of 10 minute intervalls. The duration of one cycle was 1 min and contained 6s observations and 54 s stand-by. The time is given in UTC+1.

en: maximum wind speed

en: The data file contains the maximum wind speed in 10 minute intervalls. The duration of one cycle was 1 min and contained 6 s observations and 54 s stand-by. The time is given in UTC+1.

en: avergaged mass flux

en: Average mass flux of 10 min measurement interval. The Cycle duration is 1 min which includes 6 s observation and 54 s stand-by. The time is given in UTC+1.

en: minimum wind spees

en: The data file contains the minimum wind speed in 10 minute intervalls. The duration of one cycle was 1 min and contained 6s observations and 54 s stand-by. The time is given in UTC+1.

en: average wind speed

en: The data file contains the average wind speed in 10 minute intervalls. The duration of one cycle was 1 min and contained 6s observations and 54 s stand-by. The time is given in UTC+1.

en: The FlowCapt is an ultra-robust instrument measuring solid particle acoustic mass - flux intensities (g m‾ ² s‾ ¹) and wind speeds (m s‾ ¹). It was deployed at Gotschnagrat (LON: 46.859 LAT: 9.849). The vertical tube with a length of 1 m monitors snowdrift and snow-blowing; and is mounted at a height between 0.1 an 1.1 m above snow surface. The time within each data set is given in UTC+1.

acoustic-mass-flux

display_name: acoustic-mass-flux

flowcapt

display_name: flowcapt

snow-blowing

display_name: snow-blowing

snowdrift

display_name: snowdrift

wind-speed

display_name: wind-speed

en: Snow Drift Station - Flowcapt


maintainer: Matthias Haeni

en: meteo climate-change wind-speed swiss-forest-lab par meteorology precipitation relative-humidity temperature long-term

en: Data plot of the forest station (JUB)

en: Data overview for air temperature, relative humidity, precipitation, PAR, wind speed.

en: Data plot of the field station (JUF)

media_type: text/csv

en: Data file.

format: CSV

mimetype: text/csv

en: Forest station data (JUB)

en: Site photo of the field station (JUF)

en: Site photo of the field station from the side.

mimetype: image/jpeg

en: Site aerial photo (Jussy)

en: Site aerial photo from both Jussy stations. Source: Google. 2016. Site aerial photo from both Jussy stations. Retrieved November 11, 2016, from https://www.google.ch/maps

en: Site photo of the forest station (JUB)

en: Site photo of the forest station from the side.

en: High quality meteorological data are needed for long-term forest ecosystem research, particularly in the light of global change. The long-term data series published here comprises almost 20 years of measurements for two meteorological stations in Jussy in Switzerland where one station is located within a natural broad-leaved forest stand (JUB) with sessile oak (_Quercus petrea_; 90 yrs), aspen (_Populus tremula_; 60 yrs) and European hornbeam (_Carpinus betulus_; 60 yrs) as dominant tree species. A second station is situated in the very vicinity outside of the forest (field station, JUF). The meteorological time series are presented in hourly time resolution of air temperature, relative humidity, precipitation, photosynthetically active radiation (PAR) and wind speed. Jussy is part of the Long-term Forest Ecosystem Research Programme (LWF) established and maintained by the Swiss Federal Research Institute WSL.

climate-change

display_name: climate-change

long-term

display_name: long-term

meteo

display_name: meteo

meteorology

display_name: meteorology

par

display_name: par

precipitation

display_name: precipitation

swiss-forest-lab

display_name: swiss-forest-lab

temperature

display_name: temperature

educ

en: Education, culture and sport

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: Jussy, Switzerland: Long-term forest meteorological data from the Long-term Forest Ecosystem Research Programme (LWF), from 1997 onwards


en: climate-change statistical-interpolation ecology microclimate biodiversity forest radiation-transfer

en: Predicted microclimate topsoil temperatures at 5 cm below ground. 10 m spatial resolution raster files are provided for mean daily minimum (tmin), mean (tmean) and maximum (tmax) temperatures during each month from April (04) to October (10) over the period between 2012 to 2021.

en: Predicted microclimate air temperatures at 100 cm above ground. 10 m spatial resolution raster files are provided for mean daily minimum (tmin), mean (tmean) and maximum (tmax) temperatures during each month from April (04) to October (10) over the period between 2012 to 2021.

en: Predicted microclimate air temperatures at 5 cm above ground. 10 m spatial resolution raster files are provided for mean daily minimum (tmin), mean (tmean) and maximum (tmax) temperatures during each month from April (04) to October (10) over the period between 2012 to 2021.

en: Climate data matching the scales at which organisms experience climatic conditions are often missing. Yet, such data on microclimatic conditions are required to better understand climate-change impacts on biodiversity and ecosystem functioning. Here we combine a national network of microclimate temperature measurements with a novel radiative transfer model to map monthly minimum, mean and maximum temperatures during the vegetation period at a 10 meter spatial resolution across Switzerland. The temperature measurements took place in 107 sampling plots distributed across different habitat types, with 62 plots in forests, 22 below trees outside forests, and 23 in open grasslands. In each plot we measured temperature in the topsoil (-5cm), as well as in the air at 5cm and 100cm height above ground. Spatial interpolation was achieved by using a hybrid approach based on linear mixed effects models with input from detailed radiation estimates that account for topographic and vegetation shading, as well as other predictor variables related to the macroclimate, topography and vegetation height. Our data reveals strong horizontal and vertical variability in microclimate temperature, particularly for maximum temperatures at 5 cm above the ground and within the topsoil. Compared to macroclimate conditions as measured by weather stations outside forests, diurnal air and topsoil temperature ranges inside forests were reduced by up to 3.0 and 7.8 °C, respectively, while below trees outside forests, e.g. in hedges and below solitary trees, this buffering effect was 1.8 and 7.2 °C. We also found that in open grasslands, maximum temperatures at 5 cm above ground are on average 3.4 °C warmer than that of macroclimate, suggesting that in such habitats heat exposure close to the ground is often underestimated when using macroclimatic data. After accounting for macroclimate effects, microclimate patterns were primarily driven by radiation, with particularly strong effects on maximum temperatures. Results from spatial block cross-validation revealed predictive accuracies as measured by RSME’s ranging from 1.18 to 3.43 °C, with minimum temperatures generally being predicted more accurately than maximum temperatures. The microclimate maps presented here enable a more biologically relevant perspective when analysing climate-species interactions, which is expected to lead to a better understanding of biotic and ecosystem responses to climate and land use change.

biodiversity

display_name: biodiversity

ecology

display_name: ecology

forest

display_name: forest

microclimate

display_name: microclimate

radiation-transfer

display_name: radiation-transfer

statistical-interpolation

display_name: statistical-interpolation

en: Monthly topsoil and near surface microclimate temperature data for Switzerland


en: forest-productivity land-cover snow-simulation clm5 evapotranspiration land-use oshd snow high-resolution

en: Forcing land surface datasets used for the CLM5 simulations at 1km, 0.25° and 0.5° resolution. For the 1km resolution both the standard global (LU_Gl) and the high-resolution dataset (LU_HR) are provided.

en:
12 gridded CLM5 simulations over the spatial extent of Switzerland:
- 1km, 0.25deg, 0.5deg
- 3 different meteorological forcings (Clim_CRU, CLIM_CRU*, CLIM_OSHD)
- 2 different land use forcings
each with the following outputs:
- daily snow depth (file SNOW_DEPTH.nc)
- monthly summed gross primary production (file FPSN_MONTH_SUM.nc)
- monthly summed evapotranspiration (file QFLX_EVAP_TOT_MONTH_SUM.nc).
Temporal extent of all simulations: 01/01/2015 - 31/12/2020.

en: Point-scale CLM5 simulation output of snow depth and snow water equivalent for 9 different simulation scenarios, each performed at 36 snow station locations across Switzerland. Please have a look at table A1 in the appendix of the linked publication for coordinates of the stations. Additional information on the setup, and the differences between simulation setups can also be found in the linked publication.

en:
This dataset contains Community Land Model 5 (CLM5) simulation output over the spatial extent of Switzerland at different resolutions and based on a range of input datasets. It further contains land-use surface data used for the CLM5-simulations.

**Detailed description of the CLM5 simulation setup and the various input datasets can be found in the accompanying publication: https://doi.org/10.5194/egusphere-2023-1832.**

 CLM5 simulation output

This dataset includes gridded CLM5 simulations of snow depth, gross primary productivity (GPP) and evapotranspiration at different resolutions ( 1km, 0.25° and 0.5°) and based on a range of input datasets over the spatial extent of Switzerland (see folder *gridded_CLM5_simulations*). Additionally, point-scale CLM5 simulations of snow depth and snow-water-equivalent at 36 snow-station locations (see folder *point_scale_CLM5_simulations*) are included. Latitude, longitude and elevation for these station locations can be found in table A1 of the above-mentioned publication. All simulation output spans from 01/01/2015 - 31/12/2019.

Included CLM5 simulation results are based on 3 different meteorological forcing datasets:
* Clim_CRU: standard global dataset, we used the recent state-of-the-art standrd global dataset CRU-JRA (https://catalogue.ceda.ac.uk/uuid/aed8e269513f446fb1b5d2512bb387ad)

* Clim_CRU*: ClimCRU upraded by downscaling temperature data using a temperature lapse rate of -6.5K/1000m and a high-resolution DEM

* Clim_OSHD: highest level of detail, meteorological forcing generated according to methods developed by the Operational Snow Hydrological Service (OSHD), at 1km spatial and 1hour temporal resolution</li>

 Land-use surface data

This dataset further includes forcing land surface datasets used for the CLM5 simulations at 1km, 0.25° and 0.5° resolution (see folder *surface_landuse_datasets*). For the 1km resolution both the standard global (LU_Gl) and the high-resolution dataset (LU_HR), which includes a higher level of detail and is based on a more up-to-date land use datase, are provided. More details on these two datasets can be found in the above-mentioned publication.

evapotranspiration

display_name: evapotranspiration

forest-productivity

display_name: forest-productivity

high-resolution

display_name: high-resolution

land-cover

display_name: land-cover

land-use

display_name: land-use

oshd

display_name: oshd

snow

display_name: snow

snow-simulation

display_name: snow-simulation

en: Multi-resolution CLM5 simulations across Switzerland


maintainer: Jana von Freyberg

en: snowpack-outflow snowmelt-lysimeter solutes stable-water-isotopes snowmelt-rate

en: The dataset contains volumes, solutes and stable water isotopes of snowpack outflow at daily resolution. 10-minute data are provided of the measurements taken by three snowmelt lysimeter systems at spatially-distributed locations.

en:
This data contain volumes, solutes and isotopes of snowpack outflow measured by a snowmelt lysimeter system at three locations in the southern Alp catchment, situated Central Switzerland. The river Alp is a snow-dominated catchment situated in Central Switzerland characterized by an elevation range from 840 to 1898 m a.s.l.
The dataset provides solutes (major anions and cations, trace metals) and stable water isotopes and water fluxes (snowpack outflow volumes) at daily intervals from several sampling locations. Additionally, the data measured by the snowmelt lysimeter system are provided in 10-minute resolution.

snowmelt-lysimeter

display_name: snowmelt-lysimeter

snowmelt-rate

display_name: snowmelt-rate

snowpack-outflow

display_name: snowpack-outflow

solutes

display_name: solutes

stable-water-isotopes

display_name: stable-water-isotopes

en: Daily data of the volumes, solutes and isotopes in snowpack outflow measured at three locations in the southern Alp catchment


maintainer: Frank Techel

en: avalanche-fatalities avalanche-statistics avalanche-accident-statistics long-term-trends avalanche-accident

en: Data avalanche fatalities 1969/1970 - 2014/2015

media_type: text/plain

en: The data comprises avalanche fatality data from the Alpine regions in the seven countries Austria, France, Germany, Italy, Liechtenstein, Slovenia, and Switzerland.

format: TXT

mimetype: text/plain

en:
During the last 45 years, about 100 people lost their lives in avalanches in the European Alps each year. Avalanche fatalities in settlements and on transportation corridors have considerably decreased since the 1970s. In contrast, the number of avalanche fatalities during recreational activities away from avalanche-secured terrain doubled between the 1960s and 1980s and has remained relatively stable since, despite a continuing strong increase in winter backcountry recreational activities.

Data complementing Figure 2 in:
_"Avalanche fatalities in the European Alps: long-term trends and statistics"_, by Techel, F., Jarry, F., Kronthaler, G., Mitterer, S., Nairz, P., Pavšek, M., Valt, M., and Darms, G.

Data description:
please refer to section 2 (Data and Methods) in the mentioned publication

avalanche-accident

display_name: avalanche-accident

avalanche-accident-statistics

display_name: avalanche-accident-statistics

avalanche-fatalities

display_name: avalanche-fatalities

avalanche-statistics

display_name: avalanche-statistics

long-term-trends

display_name: long-term-trends

educ

en: Education, culture and sport

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: Avalanche fatalities in the European Alps (1969/1970 - 2014/2015)


maintainer: Athanasios Nenes

en: cloud-modeling cloud-droplets weissfluhjoch ccn hygroscopicity raclets dmt-ccn-chamber supersaturation sigma-w

en: CCN data Weissfluhjoch

en:
In-situ CCN measurements were conducted between February 24 and March 8 2019 at Weissfluhjoch. The data file contains:

* Date and time (DD/MM/YYYY hh:mm:ss) in UTC
* Filtered CCN number concentrations (in cmˉ³) measured at 6 discrete supersaturations (SS) ranging from 0.09% to 0.74%. The name of each CCN column is indicative of the SS developed within the instrument.
* Instrument characteristics such as sample temperature (in °C) and pressure (in mbar)
* A code that refers to the reason of filtering.

Missing or filtered CCN values are indicated by "-999", while a declaration of each "Error_code" can be found in the following list:

_Error_code_:

0000: Measurements without error

1000: Period of transient operation after a supersaturation change

2000: Sharp change (decrease) in the room temperature housing the instrument, which induces a reset in column temperature

3000: Irregular values in the room temperature housing the instrument

9999: Missing data

en: Predicted cloud droplet number concentrations Weissfluhjoch

en:
In-situ measurements of aerosol size distributions along with updraft velocities collected from a wind Doppler Lidar are coupled with a state-of-the art droplet activation parameterization (Morales and Nenes, 2014) to determine the cloud droplet number and maximum in-cloud supersaturation that can potentially form over the Weissfluhjoch station between February 24 and March 8 2019. For this, a hygroscopicity parameter of 0.25 is assumed, according to the CCN-derived values. The data file contains:

* Date and time (DD/MM/YYYY hh:mm:ss) in UTC
* The wind-lidar derived standard deviation of updraft velocities (sigma-w) in m/s, used to apply the parameterization employing a single characteristic velocity (Morales and Nenes, 2010)
* The maximum predicted cloud parcel supersaturation (Smax%)
* The total in-situ aerosol number concentration (Naer) in cmˉ³, measured by the SMPS
* The predicted cloud droplet numbers (Nd) in cmˉ³
* The activation fraction (%)

en: Hygroscopicity parameter Weissfluhjoch

en:
The aerosol hygroscopicity parameter is derived combining the CCN and SMPS size distribution data collected between February 24 and March 8 2019 at Weissfluhjoch. The data file contains:

* Date and time (DD/MM/YYYY hh:mm:ss) in UTC
* The instrument supersaturation (SS%)
* The calculated hygroscopicity parameter (kappa)
* The calculated critical dry diameter of the particles (Dcr) in nm.

Missing values are indicated by "-999".

en:
Cloud Condensation Nuclei (CCN) data: A Droplet Measurement Technologies (DMT) single-column continuous-flow streamwise thermal gradient chamber (CFSTGC; Roberts and Nenes, 2005) was deployed at the measurement site Weissfluhjoch (2700 m a.s.l., LON: 9.806475, LAT: 46.832964) to record the in-situ CCN number concentrations between February 24 and March 8 2019 for different supersaturations (SS). To account for the difference between the ambient (~735 mbar) and the calibration pressure (~800 mbar), the SS reported by the instrument is adjusted by a factor of 0.92. The CFSTGC was cycled between 6 discrete SS values ranging from 0.09% to 0.74%, producing a full CCN spectrum every hour. The raw CCN measurements are filtered to discount periods of transient operation and whenever the room temperature housing the instrument changed sufficiently to induce a reset in column temperature. Additional information can be found in Section 2.1.2 [here](https://acp.copernicus.org/preprints/acp-2020-1036/).

Hygroscopicity data: The CCN number concentration measurements were directly related to the size distribution and total aerosol concentration data measured by the Scanning Mobility Particle Size Spectrometer (SMPS) instrument at the same station (https://www.envidat.ch/dataset/aerosol-data-weissfluhjoch) to infer the particles hygroscopicity parameter (kappa). For each SMPS scan, the particles critical dry diameter (Dcr) is estimated by integrating backward the SMPS size distribution, until the aerosol number matches the CCN concentration observed for the same time period as the SMPS scan. Assuming the particle chemical composition is internally mixed, the kappa is determined from Dcr and SS, applying Köhler theory. Additional information can be found in Section 2.2 [here](https://acp.copernicus.org/preprints/acp-2020-1036/).

Predicted cloud droplet numbers: Droplet calculations are carried out with the physically based aerosol activation parameterization of Morales and Nenes (2014), employing the “characteristic velocity” approach of Morales and Nenes (2010). Aerosol size distribution observations required to predict the cloud droplet numbers and maximum in-cloud supersaturation are obtained from the SMPS instrument deployed at Weissfluhjoch. The required vertical velocity measurements are derived from the wind Doppler Lidar (https://www.envidat.ch/dataset/lidar-wind-profiler-data) deployed at Davos Wolfgang and are extracted for the altitude of interest, being 1100 m above ground level for Weissfluhjoch. Additional information can be found in Section 2.3 [here](https://acp.copernicus.org/preprints/acp-2020-1036/).

ccn

display_name: ccn

cloud-droplets

display_name: cloud-droplets

cloud-modeling

display_name: cloud-modeling

dmt-ccn-chamber

display_name: dmt-ccn-chamber

hygroscopicity

display_name: hygroscopicity

raclets

display_name: raclets

sigma-w

display_name: sigma-w

supersaturation

display_name: supersaturation

weissfluhjoch

display_name: weissfluhjoch

en: CCN, hygroscopicity, predicted cloud droplet numbers Weissfluhjoch


en: atmospheric-conditions temperature-profiles wind radiation precipitation

en: Site photo 1

en: This site photo is outdated and has been replaced with an updated version (see description).

en: STB2 CSV

en: This dataset is outdated and has been replaced with an updated version (see description).

en: Site photo 3

en: README

en: This description is outdated and has been replaced with an updated version (see description).

en: DATA ACCESS

en: This data access is outdated and has been replaced with an updated version (see description).

en: Site photo 2

en: Overview plot

media_type: image/png

en: This overview plot is outdated and has been replaced with an updated version (see description).

format: PNG

en: Latest data from Stillberg climate station

en:
 Important
This EnviDat entry is outdated. The most recent, usable version of the data can be found under the new EnviDat entry "Long-term meteorological station Stillberg, Davos, Switzerland at 2090 m a.s.l.." The entry can be found under this link <https://www.envidat.ch/#/metadata/meteo-stillberg> and with this DOI <https://doi.org/10.16904/envidat.396>.

atmospheric-conditions

display_name: atmospheric-conditions

precipitation

display_name: precipitation

radiation

display_name: radiation

temperature-profiles

display_name: temperature-profiles

wind

display_name: wind

en: Long-term meteorological and snow station at 2090 m a.s.l., Stillberg, Davos, Switzerland (1975 - present)


en: metamorphism 18o snow stable-water-isotope advection

en: Read-me

en: A short description of the data contained in the zipped-file. Recommended for reading before downloading the dataset.

en: Data files and read-me

en: raw data and micro-CT data available from contacts

en:
Stable water isotopes (δ18O) obtained from snow and ice samples of polar regions are used to reconstruct past climate variability, but heat and mass transport processes can affect the isotopic composition. Here we present an experimental study on the effect on the snow isotopic composition by airflow through a snow pack in controlled laboratory conditions. The influence of isothermal and controlled temperature gradient conditions on the δ18O content in the snow and interstitial water vapor is elucidated. The observed disequilibrium between snow and vapor isotopes led to exchange of isotopes between snow and vapor under non-equilibrium processes, significantly changing the δ18O content of the snow. The type of metamorphism of the snow had a significant influence on this process.
Ebner, P. P., Steen-Larsen, H. C., Stenni, B., Schneebeli, M., and Steinfeld, A.: Experimental observation of transient δ18O interaction between snow and advective airflow under various temperature gradient conditions, The Cryosphere Discuss., https://doi.org/10.5194/tc-2017-16, accepted, 2017.

advection

display_name: advection

metamorphism

display_name: metamorphism

snow

display_name: snow

stable-water-isotope

display_name: stable-water-isotope

educ

en: Education, culture and sport

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: Experiments on stable water isotopes,  snow metamorphism, and advection


dischmex-meteorological-measurements

maintainer: Rebecca Mott

title_for_slug: dischmex-meteorological-measurements

en: meteorological-data dischmex dischma meteo-station meteorological-measurements

en: Meteorological measurement 2014

en: data

en: Meteorological measurements 2014

en: Location of the meteorological stations

en: Meteorological measurement 2015

en: Overview sensors

en: Meteorological measurements 2016

en:
Meteorological measurements recorded in the Dischma valley from 2014-2016. In 2014 and 2015 we used 11 mobile weather stations from sensorscope to record meteorological parameter in the upper Dischma valley in the closer surroundings of the Gletschboden area. The meteorological stations are eqiupped with at least air temperature/humidity, wind velocity and wind direction sensors. Some stations are additionally equipped with precipitation, shortwave radiation and snow surface temperature sensors.
Three transects were installed at different aspects and were equipped with air temperature/humidity and wind sensors. Transect 1 (stations 2-4) provides meteorological Information on an east-north-east facing slope at elevations ranging between 2100 m and 2500 m. Transect 2 (stations 5-7) provides meteorological Information on a south-west slope and transect 3 (stations 8-10) on a north-west slope. Station 1 is fully equipped with meteorological sensors (temperature/humidity, wind, IR, up and downwand shortwave radiation and precipitation).
In 2016, mobile stations from sensorscope were replaced with six permanent meteorological stations. Meteorological stations 1-3 are equipped with an air temperature/humidity sensor, two wind speed sensors, a wind direction sensor and an incoming and outgoing shortwave radiation sensor. Stations 4 and 6 are equipped with an air temperature/humidity sensor and a wind speed/direction sensor. Station 5 is a equipped with an air temperature/humidity sensor, a wind speed/direction sensor, a snow surface temperature sensor, an incoming and outgoing shortwave radiation sensor and an incoming longwave radiation sensor.

dischma

display_name: dischma

dischmex

display_name: dischmex

meteo-station

display_name: meteo-station

meteorological-data

display_name: meteorological-data

meteorological-measurements

display_name: meteorological-measurements

en: DISCHMEX - Meteorological measurements


en: snow-instability snow danger-level avalanche avalanche-forecasting avalanche-danger

en: Read-me file

en: This read-me file contains the descriptions of the variables.

en: Field observations of snow instabilities

en:
This data set includes 589 snow profile observations including a rutschblock test, observations of signs of instability and an assessment of the local avalanche danger level, mainly recorded in the region of Davos (eastern Swiss Alps) during the winter seasons 2001-2002 to 2018-2019.

These data were analyzed and results published by Schweizer et al. (2021). They characterized the avalanche danger levels based on signs of instability (whumpfs, shooting cracks, recent avalanches), snow stability class and new snow height.

The data are provided in a csv file (589 records); the variables are described in the corresponding read-me file.

These data are the basis of the following publication: Schweizer, J., Mitterer, C., Reuter, B., and Techel, F.: Avalanche danger level characteristics from field observations of snow instability, Cryosphere, 15, 3293-3315, https://doi.org/10.5194/tc-15-3293-2021, 2021.

 Acknowlegements
Many of the data were recorded by SLF observers and staff members, among those Roland Meister, Stephan Harvey, Lukas Dürr, Marcia Phillips, Christine Pielmeier and Thomas Stucki. Their contribution is gratefully acknowledged.

avalanche

display_name: avalanche

avalanche-danger

display_name: avalanche-danger

avalanche-forecasting

display_name: avalanche-forecasting

danger-level

display_name: danger-level

snow-instability

display_name: snow-instability


maintainer: Albrecht von Boetticher

en: dberisintermixing debris-flow finite-volumes barrier-impact-simulation murgang interfoam shallow-landslide hangmuren natural-hazard

en:
This version of debrisInterMixing is based on OpenFOAM Version 4.x and was tested on Ubuntu 18.04.1 LTS.
Please follow the instructions given in ReadMe_debrisInterMixing4.pdf for installation.

en: debrisInterMixing for OF-Version 6

en: Installation Instructions for debrisInterMixing-6

en: These are the installation instructions for debrisInterMixing6

en: These are the installation instructions for debrisInterMixing4

en:
Here the updated versions of debrisInterMixing are provided for download. The first OpenFoam-compatible Version 2.3.x are available as supplement to v. Boetticher, A., Turowski, J. M., McArdell,W. B., Rickenmann, D., Hürlimann, M., Scheidl, C., and Kirchner, J. W.: DebrisInterMixing-2.3: A Finite Volume solver for three dimensional debris flow simulations based on two calibration parameters. Part two: model validation with experiments. Geoscientific Model Development, 10, 11: 3963-3978. doi: 10.5194/gmd-10-3963-2017.
DebrisInterMixing is a Volume-of-Fluid based Finite Volume code that accounts for shear-thinning sensitive shares of fine sediment suspension together with pressure-sensitive components of the gravel grains within debris flow mixtures. All model properties can be derived from a material sample except for a grid-sensitive calibration parameter.
For more information, please contact albrecht.vonboetticher@wasserbau.ch.

For a recent summary on applications see the DFHM8 contribution at https://www.e3s-conferences.org/articles/e3sconf/abs/2023/52/e3sconf_dfhm82023_02024/e3sconf_dfhm82023_02024.html - DOI: https://doi.org/10.1051/e3sconf/202341502024

UPDATE: DebrisInterMixing for OpenFOAM-7 is available, please contact albrecht.vonboetticher@wasserbau.ch. DebrisInterMixing with OpenFOAM-10 is ready but not yet validated.

barrier-impact-simulation

display_name: barrier-impact-simulation

dberisintermixing

display_name: dberisintermixing

debris-flow

display_name: debris-flow

finite-volumes

display_name: finite-volumes

hangmuren

display_name: hangmuren

interfoam

display_name: interfoam

murgang

display_name: murgang

natural-hazard

display_name: natural-hazard

shallow-landslide

display_name: shallow-landslide

educ

en: Education, culture and sport

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: Three-dimensional debris flow simulation tool debrisInterMixing


maintainer: Leonie Schönbeck

en: drought acclimation fluorescence pinus-sylvestris vpd gas-exchange photosynthesis

en: Methods ACi curves

en:
Parameters and methods for CO2 response curves of Photosynthesis.

Metatdata format by
Ely et al (2021). A reporting format for leaf-level gas exchange data and metadata. Ecological Informatics. https://doi.org/10.1016/j.ecoinf.2021.101232

en: Instrument details

en:
Instrument details for all LiCor instruments used during collection of dataset.

Metatdata created following guidelines from
Ely et al (2021). A reporting format for leaf-level gas exchange data and metadata. Ecological Informatics. https://doi.org/10.1016/j.ecoinf.2021.101232

en: Methods light response

en: Methods and parameters for light response curves

en: Methods fluorescence

en:
Parameters and methodology for Fluorescence measurements

Metadata format from
Ely et al (2021). A reporting format for leaf-level gas exchange data and metadata. Ecological Informatics. https://doi.org/10.1016/j.ecoinf.2021.101232

en: Variable names and units

en: Variable names, description and units for the Pfynwald Gas exchange data

en: Pfynwald gas exchange

en:
Full dataset of Pfynwald gas exchange data taken in the period from June 2013 to October 2020.
All metdata can be found in attached documents.
Data uploaded after quality control using guidelines by Ely et al (2021). A reporting format for leaf-level gas exchange data and metadata. Ecological Informatics. https://doi.org/10.1016/j.ecoinf.2021.101232

en: Methods survey

en: Parameters and methods for point measurements / survey measurements

en: Methods diurnal measurements

en:
Parameters and methodology for diurnal measurements

Metadata format from
Ely et al (2021). A reporting format for leaf-level gas exchange data and metadata. Ecological Informatics. https://doi.org/10.1016/j.ecoinf.2021.101232

en:
Gas exchange was measured on control, irrigated and irrigation-stop trees at the irrigation experiment Pfynwald, during the years 2013, 2014, 2016-2020. The measurement campaigns served different purposes, resulting in a large dataset containing survey data, CO2 response curves of photosynthesis, light response curves of photosynthesis, and fluorescence measurements. Measurements were done with LiCor 6400 and LiCor 6800 instruments. Until 2016, measurements were done on excised branches or branches lower in the canopy. From 2016 onwards, measurements were done in the top of the canopy using fixed installed scaffolds.
All metadata can be found in the attached documents.

acclimation

display_name: acclimation

drought

display_name: drought

fluorescence

display_name: fluorescence

gas-exchange

display_name: gas-exchange

photosynthesis

display_name: photosynthesis

pinus-sylvestris

display_name: pinus-sylvestris

vpd

display_name: vpd

en: 2013-2020 gas exchange at Pfynwald


wind-lidar-davos-wolfgang

title_for_slug: wind-lidar-davos-wolfgang

en: raclets wind lidar wolfgangpass profiles

en: Wind LIDAR data Wolfgang

en: A Leosphere WidCube 100S was deployed at Davos Wolfang, measuring wind profiles as well as performing PPI and RHI scans. Time format is in UTC with highest time resolution of 5 seconds.

en: Scanning wind Lidar from Meteoswiss was installed at Davos Wolfgang (LON: 9.853594, LAT: 46.835577) and measured from 200 m above ground to 8100 m. The time resolution is up to 5 seconds. The Lidar was measuring wind profiles but also performed plan position indicator (PPI) and range height indicator (RHI) scans.

lidar

display_name: lidar

profiles

display_name: profiles

raclets

display_name: raclets

wind

display_name: wind

wolfgangpass

display_name: wolfgangpass

educ

en: Education, culture and sport

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: Wind LIDAR Davos Wolfgang


weather-station-davos-wolfgang

title_for_slug: weather-station-davos-wolfgang

en: relative-humidity raclets temperature pressure weather

en: Weather Station Davos Wolfgang

en: The data file contains date and time (YYYY-MM-DD hh:mm:ss) in UTC, temperature (°C), relative humidity (%), pressure (hPa) at 10 m above ground and above sea level. The data was averaged over 10 minutes.

en: The dataset contains weather parameters measured at Davos Wolfgang (LON: 9.853594, LAT: 46.835577).

pressure

display_name: pressure

relative-humidity

display_name: relative-humidity

temperature

display_name: temperature

weather

display_name: weather


en: avalanches shapefile alps observations snow

en: Selected wet snow avalanche activity data Davos, Switzerland (2011-2014)

en: Zip archive with shapefiles for the selected wet snow avalanche polygons, including metadata.

en:
Polygons of wet snow avalanches in the Davos area, as documented by the Swiss avalanche warning service. The georeferenced outlines of the avalanches contain both the release as well as the deposit area, but without separating between both.

The dataset is a subset of the total record of 1615 avalanches classified as wet snow avalanches from October 2011 - September 2014, containing those 255 avalanches exceeding 0.0125 km^2. Every polygon comes with meta data, including the date of occurrence.

This dataset is the underlying dataset to:
Wever, N., Vera Valero, C. and Techel, F. (2018) _Coupled snow cover and avalanche dynamics simulations to evaluate wet snow avalanche activity_. Submitted to J. Geophys. Res., in review.

alps

display_name: alps

avalanches

display_name: avalanches

observations

display_name: observations

shapefile

display_name: shapefile

snow

display_name: snow


maintainer: Felix Neff

en: grassland functional-diversity insects restoration functional-traits topsoil-removal diversity long-term-experiment

en: Insect abundance

en:
Abundance of adult insects recorded in the samplings on all experimental sites

- **Plot**: ID of Plot
- **Treatment**: Experimental treatment
- **Species**: Insect species name (following [Fauna Europaea](https://fauna-eu.org))
- **Author**: Author and year of species' description (following [Fauna Europaea](https://fauna-eu.org))
- **Group**: Insect group as used in the analyses
- **Number_Adults**: Number of adult individuals recorded
- **Herbivore**: Logical indicating whether the species is feeding as a herbivore (*TRUE*) or not (*FALSE*)

en: Insect traits

en:
Functional traits of all herbivorous insect species sampled in the study.

- **Species**: Insect species name (following [Fauna Europaea](https://fauna-eu.org))
- **Author**: Author and year of species' description (following [Fauna Europaea](https://fauna-eu.org))
- **Group**: Insect group as used in the analyses
- **Body volume**: Body volume determined by body length, body width and body height (in mm$^3$)
- **Body_shape**: Ratio of body length to body width
- **Hind_femur_shape**: Ratio of hind-femur length to hind-femur width
- **Hind_front_leg_ratio**: Ratio of front-leg length to hind-leg length (leg length = femur length + tibia length)
- **Wing_length_rel**: Ratio of wing length to body length
- **Leg_length_rel**: Ratio of front-leg length to body length (leg length = femur length + tibia length)
- **Antenna_length_rel**: Ratio antenna length to body length
- **Eye_width_rel**: Ratio of eye width to head width (Auchenorrhyncha, Heteroptera) / to head height (Orthoptera)
- **Feeding_specialization**: Insect specialization on food source (*m*: monophagous, *o*: oligophagous, *p*: polyphagous)
- **Feeding_tissue**: Feeding tissue used for feeding (*c*: chewers, *x*: xylem, *p*: phloem, *m*: mesophyll, *m-p/r*: mesophyll as well as phloem and/or reproductive organs, *r*: reproductive organs, *se*: ripe seeds)
- **Hibernation**: Hibernation stage (*e*: egg, *e/n*: egg and nymph, *n*: nymph, *a*: adult)
- **Generations**: Number of generations per year (*1.5* stands for *1-2* generations per year)
- **Moisture_pref_mean**: mean of preferred habitat moistures (*1*: xerophilous, *2*: moderately xerophilous, *3*: moderately mesohygrophilous, *4*: mesohygrophilous, *5*: moderately hygrophilous, *6*: hygrophilous, *7*: moderately hydrophilous, *8*: hydrophilous)
- **Moisture_pref_range**: range of preferred habitat moistures (indicating degree of specialization)

en: Plot information

en:
Information on the experimental plots.

- **Plot**: ID of Plot
- **Treatment**: Experimental treatment
- **Landuse_history**: recent agricultural use for Initial; agricultural use before restoration for all restored sites
- **Last_tilled**: Last time the site was tilled
- **Intensity**: Frequency and intensity of mowing and manuring (*intensity1*: mowing once and no manure, i*ntensity2*: 2-3 times mowing and no manure, *intensity3*: 2-3 times mowing and manuring, *intensity4*: 4-5 times mowing and manuring)
- **Slope**: slope gradient according to classes defined by FAO (1990)
- **X**: X coordinate of the plot (CH1903)
- **Y**: Y coordinate of the plot (CH1903)
- **Cluster**: Spatial cluster of the plot

en:
This dataset contains all data, on which the following publication below is based.

**Paper Citation**:

Neff, F., Resch, M. C., Marty, A., Rolley, J. D., Schütz, M., Risch, A. C, Gossner, M. M. 2020. Long-term restoration success of insect herbivore communities in semi-natural grasslands: a functional approach. Ecological Applications, 30, e02133. [10.1002/eap.2133](https://doi.org/10.1002/eap.2133)

Please cite this paper together with the citation for the datafile.

 Methods

 Study site
The study area is situated within and nearby to Eigental nature reserve (47°27’36” to 47°29’06” N, 8°37’12” to 8°37’44” E, 461 to 507 m a.s.l.) in the vicinity of Zurich airport (Canton Zurich, Switzerland). Mean annual precipitation and temperature is 903 ± 136 mm and 9.14°C ± 0.50°C (mean ± SD for 2007-2017 (*MeteoSchweiz 2018*)). In 1967, the Eigental nature reserve was established to protect small and isolated remnants of species-rich, semi-natural grasslands (roughly 12 ha), which were embedded in an otherwise intensively managed landscape. It is characterized by oligo- to mesotrophic Molinion (semi-wet, matrix species *Molinia caerulea*) and Mesobromion (semi-dry, matrix species *Bromus erectus*) meadows (*Delarze et al. 2015*), reflecting small-scale habitat heterogeneity, mainly due to site-specific groundwater levels and slope inclination. As in most Central European grasslands, management is necessary to prevent shrub and tree invasions as well as to secure low levels of available soil nutrients and thus to maintain these species-rich habitats ([*Poschlod and WallisDeVries 2002*](https://doi.org/10.1016/S0006-3207(01)00201-4)).
In 1990, the government of the Canton Zurich decided to enlarge the Eigental nature reserve as a counter measure against degradation and biodiversity loss in semi-natural grasslands due to overutilization and the excessive input of nutrients (mostly nitrogen). Eleven patches of adjacent intensively managed grassland (in total roughly 20 ha) were targeted to be transformed into semi-natural grasslands. As a first restoration measure, fertilization was ceased, and biomass harvested three times to remove excessive soil nutrients from the original system and thus benefit plant species with low competitive ability on the long run. In 1995, the restoration efforts were increased and a large-scale experiment comprising three restoration measures with increasing intervention intensities was implemented:

- **Harvest only**: Initial restoration measures were continued with mowing and removing of the aboveground biomass two times a year (early summer and autumn).
- **Topsoil**: Removal of topsoil, depending on the thickness of the A horizon the upper 10 to 20 cm, in four randomly selected areas within the eleven patches in late autumn 1995. The size of the restoration area depended on individual patch size (2700 to 7000 m2).
- **Topsoil + Propagules**: Plant propagules were added on half of the area where topsoil was removed via application of fresh, seed-containing hay and hand-collected propagules of target species originating from semi-dry and semi-wet species-rich grasslands with local and regional provenance (within radius of 7 to 30 km) (1995, 1996, 1997).

Management of *Topsoil* and *Topsoil + Propagules* started five years after treatment implementation and included yearly mowing and removing of aboveground biomass (late summer or early autumn). The experiment was complemented with intensively managed grassland sites that share the same agricultural history as the restored sites (**Initial**; swards dominated by *Lolium perenne*, *L. multiflorum* and *Trifolium repens*): mowing and subsequent fertilizing (manure) up to five times a year, as well as different tillage regimes. Finally, sites were selected in target semi-dry and semi-wet grasslands (**Target**) located within the Eigental nature reserve and another nature reserve nearby (Altläufe der Glatt; 47°28’29” to 47°27’41” N, 8°31’56” to 8°32’26” E, 418 to 420 m a.s.l.). The selected target sites are mown and aboveground biomass removed once a year in late summer or early autumn. For each of the five treatments, we selected eleven plots (5 m × 5 m) spread across the sites. Altogether, the experiment included 55 plots.

 Arthropod sampling
Aboveground arthropods were sampled using suction sampling on four consecutive days in early July 2017 before the grasslands were mown. Arthropods were sampled in two locations on each 5 m × 5 m plot, once in the south-western and once in the north-eastern corner to account for possible spatial heterogeneity within the plots. Arthropods were sorted to order or lower taxonomic levels and individuals were identified to species level. We focused on three groups (Hemiptera: Auchenorrhyncha, Hemiptera: Heteroptera, Orthoptera),

 Functional traits
We used two sets of functional traits in this study.

**Morphometric traits**:
Body volume, body shape, hind femur shape, hind/front leg ratio, wing length, leg length, antenna length and eye width. We used trait measurements from [*Simons et al. (2016)*](http://dx.doi.org/10.1890/15-0616.1) and [*Neff et al. (2019)*](https://doi.org/10.1007/s10980-019-00872-1) and complemented them with measurements on study specimens. These measurements were conducted using a high-resolution measuring stereo microscope (Leica DVM6, Leica Microsystems) including automated high-resolution photo stacking with the software Leica Application Suite X (LAS X, © 2018 Leica Microsystems CMS GmbH) and Leica Map Premium (Leica Microsystems, © 1996-2017 Digital Surf) at WSL Birmensdorf. The eight morphometric traits were calculated from direct measurements of body parts on specimens of all sampled species. From each species, we measured at least one female and one male specimen. Additionally, for species that show wing dimorphism, we included the different wing morphs and weighted them by their prevalence reported in literature. For few species, of which not all wing morphs were available for measurements (10 cases), we estimated relative wing length from congeneric species or from the literature.

**Life-history traits**
Based on an existing data set collected by [*Gossner et al. (2015)*](http://dx.doi.org/10.1890/14-2159.1). We included traits describing different life-history characteristics of herbivore insect species, namely: feeding specialization, feeding tissue, hibernation stage and number of generations per year, which are related to insect species’ vulnerability to changes in plant community composition, microhabitat use and disturbance tolerance. To represent potential changes in habitat moisture with abandonment of intensive land use (e.g., change in ground-water level), we also included two traits related to preferred habitat moisture of the study species: moisture preference, describing species’ optimum habitat moisture, and moisture range, which describes the species’ range of preferable moisture conditions.

 References

Delarze, R., Y. Gonseth, S. Eggenberg, and M. Vust. 2015. Lebensräume der Schweiz: Ökologie - Gefährdung - Kennarten. 3rd ed. Ott, Bern.

Gossner, M. M., N. K. Simons, R. Achtziger, T. Blick, W. H. O. Dorow, F. Dziock, F. Köhler, W. Rabitsch, and W. W. Weisser. 2015. A summary of eight traits of Coleoptera, Hemiptera, Orthoptera and Araneae, occurring in grasslands in Germany. Scientific Data 2:150013.

MeteoSchweiz. 2018. Klimabulletin Jahr 2017. MeteoSchweiz, Zürich.

Neff, F., N. Blüthgen, M. N. Chisté, N. K. Simons, J. Steckel, W. W. Weisser, C. Westphal, L. Pellissier, and M. M. Gossner. 2019. Cross-scale effects of land use on the functional composition of herbivorous insect communities. Landscape Ecology 34:2001–2015.

Poschlod, P., and M. F. WallisDeVries. 2002. The historical and socioeconomic perspective of calcareous grasslands—lessons from the distant and recent past. Biological Conservation 104:361–376.

Simons, N. K., W. W. Weisser, and M. M. Gossner. 2016. Multi-taxa approach shows consistent shifts in arthropod functional traits along grassland land-use intensity gradient. Ecology 97:754–764.

diversity

display_name: diversity

functional-diversity

display_name: functional-diversity

functional-traits

display_name: functional-traits

grassland

display_name: grassland

insects

display_name: insects

long-term-experiment

display_name: long-term-experiment

restoration

display_name: restoration

topsoil-removal

display_name: topsoil-removal

en: Grassland restoration: insects and insect traits


maintainer: EnviDat

en: research-data-management metadata-convention meteorological-data-format csv nead

en: PyNEAD (future reference implementation)

en: NEAD on GitHub

media_type: text/html

format: HTML

en: NEAD syntax v0.1 (EBNF)

en: MeteoIO (future reference implementation)

mimetype: text/html

en:
Acknowledgement: The NEAD format includes NetCDF metadata and is proudly inspired by both SMET and NetCDF formats. NEAD is designed as a long-term data preservation and exchange format.

The NEAD specifications were presented at the "WMO Data Conference 2020 - Earth System Data Exchange in the 21st Century" (Virtual Conference).

-----------------------

Summary:
The Non-Binary Environmental Data Archive (NEAD) format is being developed as a generic and intuitive format that combines the self-documenting features of NetCDF with human readable and writeable features of CSV. It is designed for exchange and preservation of time series data in environmental data repositories.

License: The NEAD specifications are released to the public domain under a Creative Commons CC0 "No Rights Reserved" international license. You can reuse the information contained herein in any way you want, for any purposes and without restrictions.

csv

display_name: csv

metadata-convention

display_name: metadata-convention

meteorological-data-format

display_name: meteorological-data-format

nead

display_name: nead

research-data-management

display_name: research-data-management

educ

en: Education, culture and sport

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: Non-Binary Environmental Archive Data (NEAD) format


vegetation-height-model-nfi

maintainer: Christian Ginzler

title_for_slug: vegetation-height-model-nfi

en: vegetation-height-model forest photogrammety point-cloud 3d

en: Thumbnail

en: 2012 Vegetation Height Model NFI

en:
Data 'Vegetation Height Model NFI 2012' available on request (christian.ginzler@wsl.ch).

A national vegetation height model was calculated for Switzerland using digital aerial images. We used the stereo aerial images acquired by the Federal Office of Topography swisstopo using the ADS80 sensor to first calculate a digital surface model (DSM) with a very high spatial resolution (1 × 1 m). The DSM was then normalized to obtain the actual vegetation heights using the digital terrain model (DTM) SwissAlti3D based on airborne laser data. Buildings are masked out using the NDVI information of the aerial images to produce a vegetation height model, and to produce a vegetation height model (VHM). Such a model will be calculated in the framework of the Swiss National Forest Inventory (NFI) with consistent methods and a very high level of detail. For covering the whole of Switzerland, we used summer aerial images from 2007 to 2012.

format: GeoTIFF

en: 2019 Vegetation Height Model NFI (current)

en:
Data 'Vegetation Height Model NFI 2019' available on request (christian.ginzler@wsl.ch).

A national vegetation height model was calculated for Switzerland using digital aerial images. We used the stereo aerial images acquired by the Federal Office of Topography swisstopo using the ADS80 sensor to first calculate a digital surface model (DSM) with a very high spatial resolution (1 × 1 m). The DSM was then normalized to obtain the actual vegetation heights using the digital terrain model (DTM) SwissAlti3D based on airborne laser data. Buildings are masked out using the NDVI information of the aerial images to produce a vegetation height model, and to produce a vegetation height model (VHM). Such a model will be calculated in the framework of the Swiss National Forest Inventory (NFI) with consistent methods and a very high level of detail. For covering the whole of Switzerland, we used summer aerial images from 2013 to 2019.

en: 2016 Vegetation Height Model NFI

en:
Data 'Vegetation Height Model NFI 2016' available on request (christian.ginzler@wsl.ch).

A national vegetation height model was calculated for Switzerland using digital aerial images. We used the stereo aerial images acquired by the Federal Office of Topography swisstopo using the ADS80 sensor to first calculate a digital surface model (DSM) with a very high spatial resolution (1 × 1 m). The DSM was then normalized to obtain the actual vegetation heights using the digital terrain model (DTM) SwissAlti3D based on airborne laser data. Buildings are masked out using the NDVI information of the aerial images to produce a vegetation height model, and to produce a vegetation height model (VHM). Such a model will be calculated in the framework of the Swiss National Forest Inventory (NFI) with consistent methods and a very high level of detail. For covering the whole of Switzerland, we used summer aerial images from 2011 to 2016.

en: Countrywide Stereo-Image Matching for Updating Digital Surface Models in the Framework of the Swiss National Forest Inventory

en: 2015 Vegetation Height Model NFI

en:
Data 'Vegetation Height Model NFI 2015' available on request (christian.ginzler@wsl.ch).

A national vegetation height model was calculated for Switzerland using digital aerial images. We used the stereo aerial images acquired by the Federal Office of Topography swisstopo using the ADS80 sensor to first calculate a digital surface model (DSM) with a very high spatial resolution (1 × 1 m). The DSM was then normalized to obtain the actual vegetation heights using the digital terrain model (DTM) SwissAlti3D based on airborne laser data. Buildings are masked out using the NDVI information of the aerial images to produce a vegetation height model, and to produce a vegetation height model (VHM). Such a model will be calculated in the framework of the Swiss National Forest Inventory (NFI) with consistent methods and a very high level of detail. For covering the whole of Switzerland, we used summer aerial images from 2010 to 2015.

en:
A national vegetation height model was calculated for Switzerland using digital aerial images.
We used the stereo aerial images acquired by the Federal Office of Topography swisstopo using the ADS80 sensor to first calculate a digital surface model (DSM) with a very high spatial resolution
(1 × 1 m and 0.5 x 0.5 m). The DSM was then normalized to obtain the actual
vegetation heights using a digital terrain model (DTM)
based on laser data with the buildings masked out, and to
produce a vegetation height model (VHM). Such a model
will be calculated in the framework of the Swiss National Forest Inventory (NFI) with consistent methods and a very
high level of detail. For covering the whole of Switzerland,
we use summer aerial images from six years.

Latest version is from 2019.

forest

display_name: forest

photogrammety

display_name: photogrammety

point-cloud

display_name: point-cloud

vegetation-height-model

display_name: vegetation-height-model

en: Vegetation Height Model NFI


maintainer: Thorsten Bartels-Rausch

en: heterogeneous solution arctic interface reaction metamorphism antarctica snow ozone chemistry alpine brine laboratory-study

en: Ozone data

en: Trend of ozone mixing ratio ( _O3mixingRatio_ppb_ with time ( _time_s_ ) as measured downstream of the snow sample during the experiments. Time "0" denotes the time when data acquisition with ozone analyser was started. And, ozone (_nOzone_molec_per_s_ ) loss for each experiment with duration of ozone exposure ( _duration_s_ ) of ozone exposure, as derived from the ozone trends shown above. Time "0" denotes the time when the carrier gas with ozone was passed via the snow sample.

en: data list

en: Lists file names, snow sample properties, and flow settings for each data-set.

en: Acetone data

en:
intensity of the acetone-water-cluster and water-cluster (as derived by a chemical ionisation mass spectrometer) with time in the carrier gas downstream of packed bed flow tube holding the snow sample or the by-pass, respectively. Time "0" denotes the time when the mass spectrometer data acquisition was started. When the carrier
gas with acetone was passed via the packed bed flow tube, that is switched from by-pass to pass the snow, acetone concentration in the carrier gas rapidly dropped due to surface adsorption and slowly recovered as the adsorption sites saturate. From this, the surface area can be obtained.

en: Matlab Script to view and plot data

en: Data Figure 1

en: Data of published Figure

en: Matlab Data

en: All data as Matlab mat file

en: Readme file

en: This file shows data, code, and plots.

en: Earth’s snow cover is very dynamic on diurnal time scales. The changes to the snow structure during this metamorphism have wide ranging impacts such as on avalanche formation and on the capacity of surface snow to exchange trace gases with the atmosphere. Here, we investigate the influence of dry metamorphism, which involves fluxes of water vapor, on the chemical reactivity of bromide in the snow. For this, the heterogeneous reactive loss of ozone at a concentration of 5-6E12 molecules cm-3 is investigated in artificial, shock-frozen snow samples doped with 6.2 uM sodium bromide and with varying metamorphism history. The oxidation of bromide in snow is one reaction initiating polar bromine releases and ozone depletions.

alpine

display_name: alpine

antarctica

display_name: antarctica

arctic

display_name: arctic

brine

display_name: brine

chemistry

display_name: chemistry

heterogeneous

display_name: heterogeneous

interface

display_name: interface

laboratory-study

display_name: laboratory-study

metamorphism

display_name: metamorphism

ozone

display_name: ozone

reaction

display_name: reaction

snow

display_name: snow

solution

display_name: solution

educ

en: Education, culture and sport

en: Data set on bromide oxidation by ozone in snow during metamorphism from laboratory study


maintainer: Leo Gallus Bont

en: swiss-geodata open-source digital-elevation-model seilaplan geoinformation-software qgis-plugin swisstopo digital-planning cable-yarding

en: Herunterladen des DHM von swisstopo Website

en: View video on youtube!

en:
In order to use the QGIS plugin ‘Seilaplan’ for digital cable line planning, a digital terrain model (DTM) is required. As an alternative to using the ‘Swiss Geo Downloader’ plugin, the DTM can be obtained directly from Swisstopo. In this tutorial we explain step by step how to download the necessary DTM from the Swisstopo Website, and how to use it in QGIS for the digital planning of a cable line using the plugin ‘Seilaplan’. Please note that the tutorial language is German!

Link to the elevation model on the swisstopo website: https://www.swisstopo.admin.ch/de/geodata/height/alti3d.html#technische_details

Link to the rope map website: https://seilaplan.wsl.ch

********************

Für die Verwendung des QGIS Plugins Seilaplan zur digitalen Seillinienplanung ist ein digitales Höhenmodell (DHM) nötig. Als Alternative zum Swiss Geo Downloader erklären wir in diesem Tutorial Schritt für Schritt, wie man das nötige Höhenmodell von der Swisstopo Webseite herunterladen und in QGIS zur Seillinienplanung verwenden kann.

Link zum Höhenmodell auf der swisstopo Webseite: https://www.swisstopo.admin.ch/de/geodata/height/alti3d.html#technische_details

Link zur Seilaplan-Website: https://seilaplan.wsl.ch

cable-yarding

display_name: cable-yarding

digital-elevation-model

display_name: digital-elevation-model

digital-planning

display_name: digital-planning

geoinformation-software

display_name: geoinformation-software

open-source

display_name: open-source

qgis-plugin

display_name: qgis-plugin

seilaplan

display_name: seilaplan

swiss-geodata

display_name: swiss-geodata

swisstopo

display_name: swisstopo

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: Seilaplan Tutorial: DTM download from swisstopo website


photogrammetric-drone-data-schurlialp

maintainer: Yves Bühler

title_for_slug: photogrammetric-drone-data-schurlialp

en: orthophoto wingtra dsm drone-data uav photogrammetry

en: Data Access

en:
- 10 cm DSM
- 10 cm HS
- 3 cm orthophoto
- original RGB images
- Agisoft Metashape Processing Report

All of the products are also available as a cloud optimized geotiff.

en: The data was collected on 16.04.2021 and on 28.05.2021 with a Wingtra Gen II and a Sony RX1 II RGB sensor to obtain snow depth and distribution data. Following the data collection, the data was processed with Agisoft Metashape. A 10cm DSM, a 10cm snow depth raster, a 3mm orthophoto and the original drone images are available for download.

drone-data

display_name: drone-data

dsm

display_name: dsm

orthophoto

display_name: orthophoto

photogrammetry

display_name: photogrammetry

uav

display_name: uav

wingtra

display_name: wingtra

en: Photogrammetric Drone Data Schürlialp


maintainer: Vanessa Burg

en: manure biogas switzerland bioenergy review

en: Biogas from animal manure in Switzerland: energy potential, technology development and resource mobilization

en: Aim of this white paper is to provide decision-makers, administrations and stakeholders with the most current research findings in order to promote the optimal use of bioenergy from manure in the Swiss energy transition. For this purpose, the results of the Swiss competence center for bioenergy research - SCCER BIOSWEET - are summarized and presented in a broader context. If nothing else is mentioned, the results refer to Switzerland and in case of the feedstock to the domestic biomass potentials.

bioenergy

display_name: bioenergy

biogas

display_name: biogas

manure

display_name: manure

review

display_name: review

switzerland

display_name: switzerland


maintainer: Marco Moretti

en: zurich wild-bees urban-biodiversity beekeeping urban-ecosystems bettergardens pollinator-experiment resource-availability city4bees urbanization gardens honeybees

en: Response and predictors used for the SEMs

en: Metadata for the predictors and response dataset

en:
Mean, standard deviation , minimum and maximum values of six functional traits. The data has the following structure:
- Bee_species: bee scientific name
- mean_trait: mean value
- sd_trait: standard deviation
_min_trait: minimum value
- max_trait: maximum value
- trait: the six traits used. ITD = Intertegular distance (mm); Pheno.duration = duration of the phenology; Pheno.start = start of the phenology; Pheno.end = end of the phenology; Rel.tongue.length= relative tongue length (mm); Daytime.activity = daily activity (h)
DistNichePart: functional dissimilarity in a multidimentional trait space defined by five traits between wild bee individuals of a wild bee species and the honeybee individuals. Values are at the species level.

en: Metadata for the predictor and response dataset

en:
The data contains the following columns:

  SiteID: numeric, the identity of the garden where the bee was sampled.
  Taxonname: character, species name
  Lecty: numeric discreet, a mesure of specialisation degree. Levels: 1 = monolectic; 2=oliolectic; 3=polilectic
  Pheno.start= numeric discreet, the starting week of the flying activity.
  Pheno.end= numeric discreet, the ending week of the flying activity.
  Pheno.duration=numeric discreet, Pheno.end - Pheno.start
  Daytime.activity = numeric continuous, individual-level measure of the day hour when the bee was sampled
  ITD = numeric continuous, individual-level measure of the InterTegular Distance, a metric of mobility in mm.
  Rel.tongue.length =numeric continuous, individual-level measure of the relative tongue length (Tongue length / ITD), a metric of specilaisation degree, in mm.

en:
Cities are socio-ecological systems that filter and select species, thus establishing unique species assemblages and biotic interactions. Urban ecosystems can host richer wild bee communities than highly intensified agricultural areas, specifically in resource-rich urban green spaces such as allotment and family gardens. At the same time, urban beekeeping has boomed in many European cities, raising concerns that the fast addition of a large number of managed bees could deplete the existing floral resources, triggering competition between wild bees and honeybees. The data has been used to investigated the interplay between resource availability and the number of honeybees at local and landscape scales and how this relationship influences wild bee diversity.

This dataset contains the raw and processed data supporting the findings from the paper: "Low resource availability drives feeding niche partitioning between wild bees and honeybees in a European city".

The data contains:
1. Bee trait measurements at the species and individual-level of five functional traits.
2. The values of the feeding niche partitioning (functional dissimilarity to honeybees)
3. The predictors of resource availability and beekeeping intensity at local and landscape scales used in the modelling of the paper for the 23 experimental sites.

beekeeping

display_name: beekeeping

bettergardens

display_name: bettergardens

gardens

display_name: gardens

honeybees

display_name: honeybees

pollinator-experiment

display_name: pollinator-experiment

resource-availability

display_name: resource-availability

urban-biodiversity

display_name: urban-biodiversity

urban-ecosystems

display_name: urban-ecosystems

urbanization

display_name: urbanization

wild-bees

display_name: wild-bees

zurich

display_name: zurich

educ

en: Education, culture and sport

en: Niche partitioning between wild bees and honeybees