en: icecube intercomparison microct snow specific-surface-area

en: artificial_snow_data set

en: The file contains all micro-CT and IC measurements of the artificial snow data set. The data set was originally produced to investigate the influence of black carbon on SSA measurements.

en: The file contains all data for the plot in figure 1 of the co-located density and SSA measurement at Summit, Greenland in May 2015, conducted by Schneebeli, Proksch, Schmid.

en: Grain survey of snow particles

en: The file contains all measurements of the artificial particles for snow types A, B, C, D and E, including the artificial particle mass in the Petri dish.

en: TARTES simulations

en: Jupyter notebook with TARTES simulations.

media_type: application/zip

en: SMP measurement files for snow types A, B, C and D.

en: Influence of black carbon on the measurement of the specific surface of snow with the near infrared method - Philipp Baumann

en: These experiments investigate different possible errors by measuring the specific surface area (SSA) of snow with the near infrared method. The influence of black carbon on this measurement was disproved, the theory was therefore validated. It shows that sunlight has no influence on the measurement with the IceCube. Wind drift snow as thin layer on the sample can increase the measured value of the specific surface by a few percent. This could be part of the error, observed in former measurements at SLF. As reference for the measured SSA values with the near infrared method, computer tomography was used to verify the SSA values.

en: IceCube and MicroCT data

en: The file contains all micro-CT and IC measurements for snow types A, B, C, D and E used in our study. All samples were processed (and stored) in a cold laboratory at -15°C.

en: Statistics of samples

en: The specific surface area (SSA) of different snow types were measured with the IceCube instrument and the Scanco Medical microCT 40. In addition, the snow particles created during the preparation of IceCube samples were counted. The difference in SSA between these instruments is explained by the formation of the surface particles. A numerical simulation using TARTES simulation support the observations.

icecube

display_name: icecube

intercomparison

display_name: intercomparison

microct

display_name: microct

snow

display_name: snow

specific-surface-area

display_name: specific-surface-area


maintainer: Michael Lehning

state: active

type: dataset

en: Data Source

en: Hourly Gridded Wind Power Time Series

format: SERVICE

en: Description

media_type: application/pdf

en: Full Data Description

format: PDF

mimetype: application/pdf

en: Coordinates of Grid Points

en:
This dataset consist of simulated hourly power production from an Enercon E82 Turbine at 100 m hub-height. It describes the hourly power output a 1MW turbine would produce in each 0.01° grid cell for the years 2016 and 2017.

100 m wind speed data was taken from the COSMO-1 model (Consortium for Small-scale Modeling 2017), which has a 0.01° horizontal resolution. The domain covered is the whole of Switzerland, with the exclusion of lakes. As such, the number of 0.01◦ pixels within Switzerland amounts to 48657.
Conversion to power output was done based on the power curve of the Enercon E82 Turbine. As power output is lower at altitude due to lower air density, we corrected for this effect as described in (Kruyt et al. 2017).

Please cite the following paper in connection with the dataset:

Paper Citation:
 > _Bert Kruyt, Jérôme Dujardin, and Michael Lehning: Improvement of wind power assessment in complex terrain: The case of COSMO-1 in the Swiss Alps, Front. Energy Res., [doi:10.3389/fenrg.2018.00102] (https://doi.org/10.3389/fenrg.2018.00102)_

mountain-wind-potential

display_name: mountain-wind-potential

topography

display_name: topography

wind-energy

display_name: wind-energy

educ

fr: Éducation, culture et sport

de: Bildung, Kultur und Sport

en: Education, culture and sport

it: Istruzione, cultura e sport

envidat

fr: EnviDat: le portail de données environnementales

de: EnviDat: das Umwelt-Datenportal

en: EnviDat: the Environmental Data Portal

it: EnviDat: il portale dei dati ambientali

fr: EnviDat est le portail de données du WSL; il offre un accès uniformisé et réglementé aux données de surveillance et de recherche en matière d’environnement. Ce portail est capable d’héberger et de publier des ensembles de données précieuses et uniques, qui sont partagées aux quatre coins de la planète. Ce faisant, EnviDat favorise la recherche et contribue à l’avancement des sciences environnementales.

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

de: EnviDat ist das Datenportal der WSL für einen einheitlichen und verwalteten Zugang zu Umweltdaten aus Monitoring- und Forschungsprojekten. Auf dem Portal können Datensätze gehostet und veröffentlicht werden. Durch die weltweite Bereitstellung einzigartiger und wertvoller Datensätze leistet EnviDat einen Beitrag zur Forschung im Bereich der Umweltwissenschaften.

it: EnviDat è il portale dati del WSL che fornisce un accesso unificato e gestito ai dati di monitoraggio ambientale e di ricerca. Il portale ha la capacità di ospitare e pubblicare serie di dati preziosi e unici che vengono condivisi in tutto il mondo. Così facendo, EnviDat promuove la ricerca e contribuisce al progresso della scienza ambientale.

political_level: other

wsl

capacity: public

type: organization

approval_status: approved

key: guid

key: uri

value: Envidat Harvester

en: Dataset on Cosmo-1 based Energy Potential in Swiss Alps


maintainer: Esther Frei

en: mountain-forest treeline stillberg long-term-experiment afforestation

format: ZIP

mimetype: application/x-zip-compressed

en:
 Background information

The Stillberg ecological treeline research site in the Swiss Alps was established in 1975, with the aim to develop ecologically, technically, and economically sustainable reforestation techniques at the treeline to reduce the risk of snow avalanches. In the course of time, additional research aspects gained importance, such as the ecology of the treeline ecotone under global change. Long-term monitoring of the large-scale high-elevation afforestation has generated data about tree growth, survival, and vitality. In addition, detailed characteristics of the microsite conditions of the research were conducted. Besides providing a scientific basis and practical guidelines for high-elevation afforestation, this research has contributed to a comprehensive understanding of ecological processes in the treeline ecotone.

 Experiment description

The Stillberg afforestation experiment was established in 1975 by planting 92,000 seedlings of *Larix decidua*, *Pinus cembra* and *Pinus mugo* ssp. *uncinata* in the alpine treeline ecotone. The afforestation site is located on a northeast-facing slope with steep, topographically highly structured terrain and covers elevations from 2075 to 2230 m a.s.l. The afforestation site was divided into 4052 square plots of 3.5 × 3.5 m, arranged in a regular species-alternating pattern over the whole area. Each plot contained 25 trees of one species (1350 plots per species), and the seedlings were systematically planted 70 cm apart. The trees have been monitored since 1975. Specifically, tree mortality was assessed annually from 1975 until 1995 and has been documented every ten years since then, with surveys in 2005 and 2015 (the next survey is due in 2025). Height of the surviving trees was measured in 1975, 1979, 1982, 1985, 1990, 1995, 2005, and 2015. In 1995, 2005, and 2015, drivers of tree vitality were assessed for a subset of trees per plot. Additionally, an extensive set of environmental parameters characterizing microsite conditions of the afforestation area were recorded before and after the planting of the trees.

 Data description

The five datasets from the afforestation experiment comprise ecological and environmental data from the main afforestation experiment in five datasets with accompanying metadata (Stillberg_afforestation_all_metadata.xlsx). All data and metadata files are bundled in a ZIP-file (Stillberg_afforestation_v1.zip). In particular, a first dataset contains environmental data characterising microsite conditions of the 4000 plots with regard to soil, topography, vegetation and microclimatic conditions (Stillberg_afforestation_plot_data_v1.csv; Stillberg_afforestation_plot_metadata_v1.csv. In each plot, the natural tree regeneration was assessed by counting seedings of several tree species in 2005 and 2015 (Stillberg_afforestation_regeneration_data_v1.csv; Stillberg_afforestation_regeneration_metadata_v1.csv). Furthermore, specific information about each of the 92’000 planted trees of the tree species is available (Stillberg_afforestation_tree_parameter_data_v1.csv; Stillberg_afforestation_tree_parameter_metadata_v1.csv). Survival data for each of the 92’000 individual trees can be found in a separate dataset (Stillberg_afforestation_tree_survival_data_v1.csv; Stillberg_afforestation_tree_survival_metadata_v1.csv). Tree growth and vitality parameters are available for all trees from 1995, and for subsets of trees for 2005 and 2015 (Stillberg_afforestation_tree_measurements_data_v1.csv; Stillberg_afforestation_tree_measurements_metadata_v1.csv).

afforestation

display_name: afforestation

long-term-experiment

display_name: long-term-experiment

mountain-forest

display_name: mountain-forest

stillberg

display_name: stillberg

treeline

display_name: treeline

en: Long-term afforestation experiment at the Alpine treeline site Stillberg, Switzerland


maintainer: EnviDat Support

en: vapor-transport python pattern-formation snow numerical-model

en:
Data and code v1.0 downloaded from the git.

Running the code requires an installation of FEniCS via docker.

en:
This python code uses the Finite Element library FEniCS (via docker) to solve the one dimensional partial differential equations for heat and mass transfer in snow. The results are written in vtk format.

The dataset contains the code and the output data to reproduce the key Figure 5 from the related publication:

_Schürholt, K., Kowalski, J., Löwe, H.; Elements of future snowpack modeling - Part 1: A physical
instability arising from the non-linear coupling of transport and phase changes, The Cryosphere, 2022_

The code and potential updates can be accessed directly through git via:

https://gitlabext.wsl.ch/snow-physics/snowmodel_fenics

numerical-model

display_name: numerical-model

pattern-formation

display_name: pattern-formation

python

display_name: python

vapor-transport

display_name: vapor-transport

en: A numerical solver for heat and mass transport in snow based on FEniCS


en: water-potential stomatal-stringency anisohydric root-distribution water-use-strategy

en: The data file contains the data shown in the Figures 2-7 in Walthert et al. (2024).

format: XLS

en:
This dataset represents the data shown in the Figures 2 - 7 of Walthert et al. (2024): Coordination between degree of isohydricity and depth of root water uptake in temperate tree species. Science of the Total Environment (https://doi.org/10.1016/j.scitotenv.2024.174346). A detailed methodical description of the data can be found in the Methods section of the paper.

Abstract
In an increasingly dry environment, it is crucial to understand how tree species use soil water and cope with drought. However, there is still a knowledge gap regarding the relationships between species-specific stomatal behaviour, spatial root distribution, and root water uptake (RWU) dynamics.
Our study aimed to investigate above- and below-ground aspects of water use during soil drying periods in four temperate tree species that differ in stomatal behaviour: two isohydric tracheid-bearing conifers, Scots pine and Norway spruce, and two more anisohydric deciduous species, the diffuse-porous European beech, and the ring-porous Downy oak. From 2015 to 2020, soil-tree-atmosphere-continuum parameters were measured for each species in monospecific forests where trees had no access to groundwater. The hourly time series included data on air temperature, vapour pressure deficit, soil water potential, soil hydraulic conductivity, and RWU to a depth of 2 m. Analysis of drought responses included data on stem radius, leaf water potential, estimated osmotically active compounds, and drought damage.
Our study reveals an inherent coordination between stomatal regulation, fine root distribution and water uptake. Compared to conifers, the more anisohydric water use of oak and beech was associated with less strict stomatal closure, greater investment in deep roots, four times higher maximum RWU, a shift of RWU to deeper soil layers as the topsoil dried, and a more pronounced soil drying below 1 m depth. Soil hydraulic conductivity started to limit RWU when values fell below 10-3 to 10-5 cm/d, depending on the soil. As drought progressed, oak and beech may also have benefited from their leaf osmoregulatory capacity, but at the cost of xylem embolism with around 50% loss of hydraulic conductivity when soil water potential dropped below -1.25 MPa. Consideration of species-specific water use is crucial for forest management and vegetation modelling to improve forest resilience to drought.

anisohydric

display_name: anisohydric

root-distribution

display_name: root-distribution

stomatal-stringency

display_name: stomatal-stringency

water-potential

display_name: water-potential

water-use-strategy

display_name: water-use-strategy

en: Water-use strategies of temperate tree species


maintainer: Christoph Marty

en: snowfall water-cycle hydrology climate-change-impacts snow

en: DORA Persistent URL

en: Synthesis report chapter

en:
This report was prepared as one of the synthesis report chapters of the Hydro-CH2018 project of the Federal Office for the Environment (FOEN). An important feature of snow cover is the fact that its volume and duration is subject to large year-to-year fluctuations. As frozen precipitation, snow cover is nothing other than a natural water reservoir that delays precipitation to runoff and is thus of outstanding importance for the seasonal water balance in Switzerland. Over a whole year, approximately 40% (22 km3) of the annual runoff currently comes from snow melting and only 1% from glacier melting. Typically, the snow cover in the Alpine region builds up over the autumn and winter months, reaches its maximum between February and May, depending on the altitude, and dominates the runoff processes during melting in the following spring and summer months.
Due to the great dependence on minus temperatures and precipitation, the snow cover reacts sensitively to temperatures above 0° Celsius and more or less precipitation. Due to climate change and the associated warming, the proportion of precipitation that falls as snow decreases measurably. In addition to this reduction in snowfall, the warmer temperatures also cause the snow cover to melt more quickly. The decline in snowfall has so far mainly affected lower altitudes, where winter temperatures often reach positive levels.
As climate change progresses, this trend is likely to continue and above all affect higher zones. Even at higher altitudes, the snow cover will then start later, melt away earlier and is increasingly no longer permanently present. This development will also have an effect on the water bodies. Today nival regimes, i.e. regimes shaped by snow, are shifting towards pluvial regimes, i.e. regimes dominated by rain. Overall, winter runoff increases, summer runoff decreases. By the end of the century, the proportion of runoff from snowmelt will decrease throughout Switzerland, albeit to a lesser extent than the proportion from glacier melt.

climate-change-impacts

display_name: climate-change-impacts

hydrology

display_name: hydrology

snow

display_name: snow

snowfall

display_name: snowfall

water-cycle

display_name: water-cycle

en: Snow and the water cycle in a changing climate


automatic-detection-of-avalanches

maintainer: Matthias Heck

title_for_slug: automatic-detection-of-avalanches

en: monitoring hidden-markov-model seismic avalanche-activity snow

en: Results and Scripts

en: This zip package contains the classification results, coherence results, reference data set, python scripts used for the classification and the start and end times for the pre-processed continuous seismic data. A further readme file is also include for more detailed information.

mimetype: application/zip

en: This dataset contains the results obtained by an automatic classification using hidden Markov models of a continuous seismic dataset. To avoid long computational times, we reduced the seismic data using pre-processing step. The start and end times of the windows used for the classification are also included in this dataset. Furthermore, an avalanche reference data set is included and the python scripts used to perform the processing steps and the classification.

avalanche-activity

display_name: avalanche-activity

hidden-markov-model

display_name: hidden-markov-model

monitoring

display_name: monitoring

seismic

display_name: seismic

educ

en: Education, culture and sport

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: Automatic detection of avalanches


maintainer: Elisabeth Hafner

en: remote-sensing reliability avalanche-mapping avalanche avalanche-size-estimation

en: AvalancheReliabilityData

en: The .zip contains all data used to conduct the reliability study as well as the results, a detailed description of the included files is contained in the included pdf. All geospatial data is provided in the Swiss Coordinate System: CH1903+ / LV95 (EPSG 2056). For any use of the data the proper citation provided is obligatory!

en:
This dataset contains the data used and collected to investigate the reliability of avalanche size estimates and avalanche outlines (see related publications). Namely this is

 Avalanche size estimates

* the 10 pictures depicting avalanches
* the survey results from the 170 participants

 Avalanche outlines mapped from oblique photographs
* the pictures of the six avalanches
* the avalanche outlines mapped by the 10 participants
* the reference mapped from the georeferenced photographs

 Avalanche outlines from remotely-sensed imagery
* the orthophotos in the four different resolutions (2m, 1m, 50cm, 25cm)
* the area of interest (AoI) delimiting the research area
* the avalanche mappings in each resolution for all five participants
* the shade masks used to separate illuminated and shaded areas

The acquisition of the orthophotos has been partially supported by the Swiss National Science Foundation (SNF; Grant N°200021_172800).

avalanche

display_name: avalanche

avalanche-mapping

display_name: avalanche-mapping

avalanche-size-estimation

display_name: avalanche-size-estimation

reliability

display_name: reliability

remote-sensing

display_name: remote-sensing

en: Data reliability study: avalanche size estimates and outlines


en: sea-salt-aerosol antarctica arctic snow ice

en: Fib 1B_3

media_type: text/plain

en: Individual data to mean shown in Figure 1B

format: TXT

mimetype: text/plain

en: Table 2

en: This table lists all NEXAFS data files in chronological order with PE carbon to oxygen signal intensity ratios -from which the atomic ratio were calculated in the paper - before ("preCtoO") and after ("postCtoO") each NEXAFS measurement. Also listed is the change in Na ("lossSodi"), O ("lossOxy"), Cl ("lossChlor"), and C ("lossCarb") signal intensity after the NEXAFS measurement compared to prior to the NEXAFS measurement.

en: This table lists all data files in chronological order. "SampleTemp" refers to the reading of the PT-1000 at the side of the sample holder. "cellPressure" is the water vapour pressure during the measurements. From this, in presence of ice, the temperature of the ice sample can be calculated which is given in the column "iceTemp". "dT" is the difference, or temperature offset, between sensor's reading and the ice samples temperature. The offset is due to the sensor being mounted away from the cooled spot of the sample were it experiences heating from warmer parts of the sample holder. The off-set is used to calibrate the temperature sensor and the resulting temperature during the experiments is given in the column "temperature". "relHum" is the relative humidity above (supercooled) liquid and "concBrine" is the concentration of a NaCl solution in mol/l in equilibrium with ice at the experimental temperature. "Area" is the integrated PE signal.

en: Fig 1F_2

en: Individual data to mean shown in Figure 1F

en: Fig 1B

en: Data in Figure 1B

en: Read Me

en: Description of the data tables

en: Fig 1C

en: Data to Figure 1C

en: Fig 1E

en: Data to Figure 1E

en: Fig 1F_1

en: Fig 1B_1

en: Fig 1F

en: Data to Figure 1F

en: Fig 1D

en: Data to Figure 1D

en: Fig 1B_2

en: Code

en: Laboratory experiments are presented on the phase change at the surface of sodium chloride – water mixtures at temperatures between 259 K and 240 K. High selectivity to the upper few nanometres of the frozen solution – air interface is achieved by using electron yield near-edge X-ray absorption fine structure (NEXAFS) spectroscopy. We present the NEXAFS spectrum of the hydrohalite.

en: Data set on interfacial supercooling and the precipitation of hydrohalite in frozen NaCl solutions by X-ray absorption spectroscopy


figures-perspective-urban-beekeeping

title_for_slug: figures-perspective-urban-beekeeping

en: urban-beekeeping urban-ecology insects hymenoptera wildbees diversity-distributions

en: DEPRECATED. Data growth urban beekeeping

media_type: text/csv

format: CSV

en: R script for the figures V1

en: Deprecated version of the R script

format: OCTET

en: DEPRECATED. Distirbution beehives among beekeepers

en: The dataset contains the number of beehives per registered beekeeper ID (annonymised) in four Swiss cities (Bern, Lausanne, Geneve, Zurich).

en: NDVI values within 3 buffers  in hives in Zurich

en:
The dataset contains the average NDVI values around beehives in Zurich at three spatial scales (250, 500 and 1000 m). It contains 3 columns_
- buffer: indicating the spatial scale
- ID: hive ID (annonymised)
- mean.NDVI: mean NDVI value

en: Distribution beehives among beekeepers

en: The dataset contains the number of beehives per registered beekeeper ID (annonymised) in four Swiss cities (Bern, Lausanne, Geneve, Zurich) and Paris.

en: R script for the figures V2

en: R script for the figures

en: Local overheating values within 3 buffers in hives in Zurich

en:
The dataset contains the average overheating values around beehives in Zurich at three spatial scales (250, 500 and 1000 m). It contains 4 columns:
- buffer: indicating the spatial scale
-ID: hive ID (annonymised)
- mean.overwarming: mean overheating value, expressed in degrees Kelvin
-mena.overwarming.cor = transformed values do degrees Celsius

en: Coordinates studied cities

en: Coordinates (LatLon format) of the cities where data from urban bee ecology studies was used.

en: Proportion honeybees and wildbees

en:
The dataset contains the proportion of wildbees and honeybees in the different studies obtained from the literature review.
Article_ID: ID for each article, in the form of "A1", "A2", ..., "An"
DOI
Authors
Year: publication year
Duration sampling (years): numerical
Start_sampling: numerical, date
End_sampling: numerical, date
Continent
Country
N. cities: number of cities sampled in the article. Numerical.
City
Sampling type: categorical. Levels: active (e.g., Hand-netting); passive (e.g., pantraps. trap-nests); both (combination of passive and active methods).
Sampling methodology: categorical. Levels: direct observations, hand-netting, pantraps, interception traps, vane traps.
Number sites: total number of study sites.
Abundance honeybees: number of honeybees recorded
Abundance wild bees: number of wildbees recorded
Total bees: total number of bees	recorded.
Proportion honeybees: Abundance of honeybees / Total number of bees
Proportion wildbees: Abundance of wildbees / Total number of bees

en: Data growth urban beekeeping

en:
The dataset contains the data of the growth of urban beekeeping in different cities.
For each city in a given year, it contains the following:
Continent.
Country.
City: the name of the city
Year: the year when the information was collected
Area: of the city
Total N. beekeepers: when available, the estimated number of beekeepers in that city for that given year
Total N. hives: when available, the estimated number of beehives in that city for that given year
Density: the total number of hives divided by the city area
Reference: the source of the information.

en: Data rank-abundance distribution urban bees

en: Bee communities, and dominance patterns, from urban ecology studies in cities around the world

en: Results literature review

en:
 The file shows the results from the literature review. Briefly, we searched papers using google scholar search engine using the following query: (“WILD BEE OR WILDBEE”)(“URBAN” OR “CITY”), and limited the time span from 2010-2023. The search query returned 200 candidate papers. In addition, we complemented the candidate papers from the literature research performed by Ferrari & Polidori (2022), adding 22 additional candidate papers. To select papers, we checked that (1) were conducted in urban areas; (2) sampled the whole bee community; (3) provided data on abundance of wildbees; (4) provided data on honeybees; and (5) provided individual abundance data of each wild bee species.
The dataset contains the following:
-Article_ID: ID for the specific article in the form "A1", "A2"..."An"
- Title: of the article
- Year: of publication
- Journal: of publication
- Publisher:
- Link: link to the publication
- DOI: when applicable
- Total abundance wild bees reported: was the total number of collected bees reported? Logical (Y/N)
- Honey bee abundance reported: was thenumber of honeybees collected reported? 	Logical (Y/N)
- Abundance per wild bee species: was the number of wildbee species sampled provided? Logical (Y/N)
- Select proportion: paper selected to calculate the proportion of honeybees and wildbees.
- Select RAD: paper selected to compute the rank-abundance distribution diagram
Comment: comments on the papers, data availability, etc.

en:
Data and code from the perspective paper "When honeybees comes to town"
The .r file provides the code to generate the figures.
In addition, this repository contains the data for the figures 1-3.
For Figure 4, part of the data is confidential, Please, refer to the contacts provided:
- For the distribution of hives in Zurich (2018): https://www.zh.ch/de/gesundheitsdirektion/veterinaeramt.html
- For the overheating map of Zurich: Prof. Dr. Eberhard Parlow / Stadt Zurich (https://www.zh.ch/de/umwelt-tiere/umweltschutz/umweltpraxis/definitionsseite/2012/68/zup068_2012_a0030_klimaanalyse-pdf.html)

diversity-distributions

display_name: diversity-distributions

hymenoptera

display_name: hymenoptera

insects

display_name: insects

urban-beekeeping

display_name: urban-beekeeping

urban-ecology

display_name: urban-ecology

wildbees

display_name: wildbees

educ

en: Education, culture and sport

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: Figures perspective urban beekeeping


biogas-aus-hofdunger-in-der-schweiz

title_for_slug: biogas-aus-hofdunger-in-der-schweiz

en: review bioenergy manure biogas switzerland

en: Biogas aus Hofdünger in der Schweiz

en: Ziel dieses Whitepapers ist es, Entscheidungsträgern, Verwaltungen und Stakeholdern die aktuellsten Forschungsergebnisse zur Verfügung zu stellen, um die optimale Nutzung von Bioenergie aus Hofdünger in der Schweizer Energiewende zu fördern. Zu diesem Zweck werden die Ergebnisse des Schweizer Kompetenzzentrums für Bioenergieforschung - SCCER BIOSWEET - zusammengefasst und in einem breiteren Kontext dargestellt. Wenn nichts anderes erwähnt wird, beziehen sich die Ergebnisse auf die Schweiz und im Falle der Ressourcen auf die heimischen Biomassepotenziale.

bioenergy

display_name: bioenergy

biogas

display_name: biogas

manure

display_name: manure

review

display_name: review

switzerland

display_name: switzerland


maintainer: Dominique Weber

en: land-use grassland management sentinel-2 mowing use-intensity remote-sensing landsat

en: Readme

en: Metadata and description of the maps and webcam-based reference data.

en: Preview time of 1st grassland management event 2020

media_type: image/png

en: Spatial distribution of the timing (day of year; DOY) of the first management event for Switzerland and for three zoomed-in regions (a, b, c). The three zoomed-in regions show different grassland-use intensities, which are reflected in the timing of the first event of the year (Weber et al., 2023; IN REVIEW)

format: PNG

en: Grassland-use intensity map 2020

en: Raster stack with information on the number and timing of grassland-management events (i.e. mowing, grazing) at a spatial resolution of 10 m × 10 m for the whole of Switzerland for 2020. See readme file for more details.

format: GeoTIFF

en: Preview number of grassland management events 2020

en: Spatial distribution of the number of management events for Switzerland and for three zoomed-in regions (a, b, c). The three zoomed-in regions show different grassland-use intensities, which are reflected in the distribution of management frequency (Weber et al., 2023; IN REVIEW)

en: Grassland-use intensity map 2021

en: Raster stack with information on the number and timing of grassland-management events (i.e. mowing, grazing) at a spatial resolution of 10 m × 10 m for the whole of Switzerland for 2021. See readme file for more details.

en: Webcam-based reference data

en: Webcam-based reference data from 2020 and 2021 (see readme).

en: Grassland-use intensity map 2019

en: Raster stack with information on the number and timing of grassland-management events (i.e. mowing, grazing) at a spatial resolution of 10 m × 10 m for the whole of Switzerland for 2019. See readme file for more details.

en: Grassland-use intensity map 2018

en: Raster stack with information on the number and timing of grassland-management events (i.e. mowing, grazing) at a spatial resolution of 10 m × 10 m for the whole of Switzerland for 2018. See readme file for more details.

en:
A rule-based algorithm [(Schwieder et al., 2022)](https://doi.org/10.1016/j.rse.2021.112795) was used to produce annual maps for 2018–2021 of grassland-management events, i.e. mowing and/or grazing, for Switzerland using Sentinel-2 and Landsat 8 satellite time series. All satellite images were processed with the [FORCE](https://force-eo.readthedocs.io) framework.

The resulting maps provide information on the number and timing of grassland-management events at a spatial resolution of 10 m × 10 m for the whole of Switzerland. For the final maps, permanent grasslands were masked using a variety of land-use layers, according to [Huber et al. (2022)](https://doi.org/10.1002/rse2.298) but replacing the crop mask with the agricultural-use data from the cantons.

We assessed the detection of management events based on independent reference data, which we acquired from daily time series of publicly available webcams that are widely distributed across Switzerland. We further tested the ecological relevance of the generated intensity measures in relation to nationwide biodiversity data (see [Weber et al., 2023](https://doi.org/10.1002/rse2.372)).

The webcam-based reference data used for verification was subsequently added on 14.02.2024.

grassland

display_name: grassland

land-use

display_name: land-use

landsat

display_name: landsat

management

display_name: management

mowing

display_name: mowing

use-intensity

display_name: use-intensity

en: Grassland-use intensity maps for Switzerland


en: fractional-snow longwave-radiation forest shading shortwave-radiation

en: Seasonal sub-canopy radiation data

en:
Seasonal, spatially aggregated incoming and outgoing shortwave radiation below an evergreen forest stand collected with a cable car system.

The presented data is used and further described in the following paper: Malle et al. (2019). Shading by Trees and Fractional Snow Cover Control the Subcanopy Radiation Budget. Journal of Geophysical Research Atmospheres. DOI:10.1029/2018JD029908.

en: Radiation Data 18.04.2019

en:
Spatiotemporal incoming/outgoing shortwave and longwave radiation as well as sunlit and shaded-snow view fractions below an evergreen forest stand in the Swiss alps. Data was collected on 18th of April 2018 along a 48m long, heterogeneous forest stand under full snow cover conditions.

The presented data is used and further described in the following paper: Malle et al. (2019). Shading by Trees and Fractional Snow Cover control the Subcanopy Radiation Budget. Journal of Geophysical Research Atmospheres. DOI:10.1029/2018JD029908.

en: Sky-view fraction along the cablecar transect

en: Data is used and described in the following paper: Malle et al. (2019). Shading by Trees and Fractional Snow Cover control the Subcanopy Radiation Budget. Journal of Geophysical Research. DOI:10.1029/2018JD029908.

en: Radiation Data 25.4.2018

en:
Spatiotemporal incoming/outgoing shortwave and longwave radiation as well as sunlit and shaded-snow view fractions below an evergreen forest stand in the Swiss alps. Data was collected on 25th of April 2018 along a 48m long, heterogeneous forest stand under partial snow cover conditions.

The presented data is used and further described in the following paper: Malle et al. (2019). Shading by Trees and Fractional Snow Cover control the Subcanopy Radiation Budget. Journal of Geophysical Research Atmospheres. DOI:10.1029/2018JD029908.

en: This data set consists of incoming and outgoing short- and longwave radiation as well as sunlit-snow-view-fraction as described in the JGR-Atmospheres paper "Shading by trees and fractional snow cover control the sub-canopy radiation budget", by Malle et al. (2019). Data was collected along a 48m long, heterogeneous forest transect between January and June 2018 close to Davos, Switzerland.

forest

display_name: forest

fractional-snow

display_name: fractional-snow

longwave-radiation

display_name: longwave-radiation

shading

display_name: shading

shortwave-radiation

display_name: shortwave-radiation

educ

en: Education, culture and sport

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.


maintainer: Océane Hames

en: snow-deposition antarctica openfoam arctic-sea-ice mosaic snow-transport

en: Snowdrift measurements around Neumayer Station III

en: Files containing the topographical data barometrically measured in June 2009 around the German Antarctic Research station Neumayer III. Those measurements are compared to the snowBedFoam simulations to assess the ability of the model to reproduce real snow distribution observations.

en: MOSAiC Met City preliminary (Level 2) wind data

en:
Extract from the preliminary MOSAiC atmospheric data (Level 2) for the time period 6th to 13th of November, 2019.
This data was used to set up the fluid forcing parameters in the snowBedFoam simulations on MOSAiC sea ice. It is being published in this repository with the kind permission from Matthew Shupe and his team.
The final processed and quality controlled version of this dataset (Level 3) has not been published yet. A complete reference will be added in this description once it is released.

en: Neumayer III simulations

en:
Snow distribution results around Neumayer Station III obtained for the sensitivity analysis and comparison to measurements. The file contains several sub-folders, namely:
-COMP: simulation output for the comparison to measurements;
-FLOW: simulation output for the study of wind forcing impact;
-simulation_exampleCase: example case of a snowBedFoam simulation with the reference Neumayer Station mesh;
-SNOW: simulation output for the study of snow properties impact;
-STRUCT: simulation output for the study of structure properties impact.

en:
OpenFOAM-5.0 scripts containing the implemented Eulerian-Lagrangian snow transport model.
The code file provided here is not updated. The most recent version of the script can be found on the WSL/SLF GitLab repository: https://gitlabext.wsl.ch/atmospheric-models/snowbedfoam-v1-0.git

en: Paper Draft

en: This is the initial draft of the paper where the snowBedFoam 1.0. results are tested against Terrestrial Laser Scan (TLS) measurements of snow dynamics on Arctic sea ice (MOSAiC expedition). It highlights the numerical limitations of our model as well as the measurement uncertainties, which may occur in such extreme environments.

en:
OpenFOAM-2.3.0. scripts containing the implemented Eulerian-Lagrangian snow transport model.

The code file provided here is not updated. The most recent version of the script can be found on the WSL/SLF GitLab repository: https://gitlabext.wsl.ch/atmospheric-models/snowbedfoam-v1-0.git

en:
snowBedFoam 1.0. is a snow transport solver implemented in the computational fluid dynamics software OpenFOAM. It is adapted from the standard multi-phase flow solver DPMFoam for application in snow-influenced environments.
To simulate aeolian snow transport, snowBedFoam 1.0. handles coupled Eulerian–Lagrangian phases, which involve a finite number of particles (snow) spread in a continuous phase (air). The snow erosion and deposition are modelled through physics-based equations similar to the ones employed in the well-established LES-Lagrangian Stochastic Model (Comola and Lehning, 2017 ; Sharma et al., 2018 ; Melo et al., 2022). This modelling approach is computationally intensive and thus adapted to simulate snow movement and distribution on small scale terrain.
First, snowBedFoam 1.0. was applied to topographical data collected on Arctic sea ice during the MOSAiC expedition (Clemens-Sewall, 2021). Together with atmospheric data from the MOSAiC Met City (Shupe et al., 2021) used for the fluid forcing, the model was able to accurately simulate the zones of erosion and deposition of snow along a complex ice ridge structure (Hames et al., 2022).
Second, snowBedFoam 1.0. was used to simulate the snow distribution around the German Antarctic research station Neumayer Station III. The effect of snow properties, fluid forcing and aerodynamic structures on the snow accumulation were assessed.
snowBedFoam 1.0 was implemented in 2 different OpenFOAM versions, namely OpenFOAM-2.3.0 and OpenFOAM-5.0. The latter offers more options for turbulence models and boundary conditions. The fundamental model equations were not changed from one implementation to the other, thus both still correspond to snowBedFoam 1.0. The two branches are called snowBedFoam-v1-2.3.0 (OpenFOAM-2.3.0) and snowBedFoam-v1-5.0 (OpenFOAM-5.0). The core codes of snowBedFoam 1.0. are directly accessible on the WSL/SLF GitLab repository (more details in the Resources section).

antarctica

display_name: antarctica

arctic-sea-ice

display_name: arctic-sea-ice

mosaic

display_name: mosaic

openfoam

display_name: openfoam

snow-deposition

display_name: snow-deposition

snow-transport

display_name: snow-transport

en: snowBedFoam: an OpenFOAM Eulerian-Lagrangian solver for modelling snow transport


en: temperature meteorology precipitation par relative-humidity meteo climate-change swiss-forest-lab long-term wind-speed

en: Site photo of the field station (NEF)

en: Site photo of the field station from the side.

mimetype: image/jpeg

en: Data plot of the forest station (NEB)

en: Data overview for air temperature, relative humidity, precipitation, PAR, wind speed.

en: Site aerial photo (Neunkirch)

en: Site aerial photo from both Neunkirch stations. Source: Google. 2016. Site aerial photo from both Neunkirch stations. Retrieved November 11, 2016, from https://www.google.ch/maps

en: Site photo of the forest station (NEB)

en: Site photo of the forest station from below (viewing upwards the slope).

en: Forest station data (NEB)

en: Data file.

mimetype: text/csv

en: Field station data (NEF)

en: Data plot of the field station (NEF)

en: High quality meteorological data are needed for long-term forest ecosystem research, particularly in the light of global change. The long-term data series published here comprises almost 20 years of measurements for two meteorological stations in Neunkirch in Switzerland where one station is located within a natural deciduous forest stand (NEB) with European beech (_Fagus sylvatica_; 160 yrs), sycamore maple (_Acer pseudoplatanus_; 160 yrs) and lime trees (_Tilia sp._; 110 yrs) as dominant tree species. A second station is situated in the very vicinity outside of the forest (field station, NEF). The meteorological time series are presented in hourly time resolution of air temperature, relative humidity, precipitation, photosynthetically active radiation (PAR) and wind speed. Neunkirch is part of the Long-term Forest Ecosystem Research Programme (LWF) established and maintained by the Swiss Federal Research Institute WSL.

climate-change

display_name: climate-change

long-term

display_name: long-term

meteo

display_name: meteo

meteorology

display_name: meteorology

par

display_name: par

precipitation

display_name: precipitation

relative-humidity

display_name: relative-humidity

swiss-forest-lab

display_name: swiss-forest-lab

temperature

display_name: temperature

wind-speed

display_name: wind-speed

en: Neunkirch, Switzerland: Long-term forest meteorological data from the Long-term Forest Ecosystem Research Programme (LWF), from 1997 onwards


maintainer: Christian G. Sommer

en: wind-crust snow wind-packing kinect wind-tunnel

en: README

en: Describes the dataset in detail

en: Processing scripts

en: Contains the Matlab- and R-scripts used to process the Kinect data

en: Kinect data

en: Links to the dataset

en:
This data sets contains the Microsoft Kinect data from 15 wind tunnel experiments on wind-packing / wind crust formation. These experiments were performed in the winter 2016/17. The Kinect measures distributed snow depth.

The Kinect data is organized per experiment. Each experiment subfolder contains the processed Kinect depth images and some additional files.

Please refer to the README for more details on the data. The processing scripts are available for download as well. The scripts are mainly provided as documentation and would need to be adjusted to be used.

This dataset is the basis of the following publication:

Sommer C.G., Lehning M. & Fierz C. (2018). Wind Tunnel Experiments: Influence of Erosion and Deposition on Wind-Packing of New Snow. Front. Earth Sci. 6:4. doi: 10.3389/feart.2018.00004

kinect

display_name: kinect

snow

display_name: snow

wind-crust

display_name: wind-crust

wind-packing

display_name: wind-packing

wind-tunnel

display_name: wind-tunnel

educ

en: Education, culture and sport

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: Wind crust formation: Microsoft Kinect data


maintainer: Leo Gallus Bont

en: digital-elevation-model swiss-geodata seilaplan cable-yarding qgis-plugin geoinformation-system open-source digital-planning swiss-geo-downloader

en: Herunterladen des DHM mit SwissGeoDownloader

en: View video on youtube!

en:
In order to use the QGIS plugin ‘Seilaplan’ for digital cable line planning, a digital terrain model (DTM) is required. The plugin ‘Swiss Geo Downloader’, which is available for the open source geoinformation software QGIS, allows freely available Swiss geodata to be downloaded and displayed directly within QGIS. It was developed in 2021 by Patricia Moll in collaboration with the Swiss Federal Institute for Forest, Snow and Landscape Research WSL. In this tutorial we describe how to download the high accuracy elevation model ‘swissALTI3D’ with the help of the ‘Swiss Geo Downloader’ and how to use it for digital planning of a cable line with the plugin ‘Seilaplan’. Please note that the tutorial language is German!

Link to the Swiss Geo Downloader: https://pimoll.github.io/swissgeodownloader

Link to Seilaplan website: https://seilaplan.wsl.ch

*********************

Für die Verwendung des QGIS Plugins Seilaplan zur digitalen Seillinienplanung ist ein digitales Höhenmodell (DHM) nötig. Das Plugin Swiss Geo Downloader, welches für das Open Source Geoinformationssystem QGIS zur Verfügung steht, ermöglicht frei verfügbare Schweizer Geodaten direkt innerhalb von QGIS herunterzuladen und anzuzeigen. Es wurde 2021 von Patricia Moll in Zusammenarbeit mit der eidgenössischen Forschungsanstalt Wald, Schnee und Landschaft WSL entwickelt. In diesem Tutorial beschreiben wir, wie man mit Hilfe des Swiss Geo Downloaders das hochgenaue Höhenmodell swissALTI3D herunterladen und für die Seillinienplanung mit dem Plugin Seilaplan verwenden kann.

Link zum Swiss Geo Downloader: https://pimoll.github.io/swissgeodownloader

Link zur Seilaplan-Webseite: https://seilaplan.wsl.ch

cable-yarding

display_name: cable-yarding

digital-elevation-model

display_name: digital-elevation-model

digital-planning

display_name: digital-planning

geoinformation-system

display_name: geoinformation-system

open-source

display_name: open-source

qgis-plugin

display_name: qgis-plugin

seilaplan

display_name: seilaplan

swiss-geo-downloader

display_name: swiss-geo-downloader

swiss-geodata

display_name: swiss-geodata

en: Seilaplan Tutorial: DTM download with SwissGeoDownloader


wind-lidar-davos-wolfgang

title_for_slug: wind-lidar-davos-wolfgang

en: wind raclets profiles wolfgangpass lidar

en: Wind LIDAR data Wolfgang

en: A Leosphere WidCube 100S was deployed at Davos Wolfang, measuring wind profiles as well as performing PPI and RHI scans. Time format is in UTC with highest time resolution of 5 seconds.

en: Scanning wind Lidar from Meteoswiss was installed at Davos Wolfgang (LON: 9.853594, LAT: 46.835577) and measured from 200 m above ground to 8100 m. The time resolution is up to 5 seconds. The Lidar was measuring wind profiles but also performed plan position indicator (PPI) and range height indicator (RHI) scans.

lidar

display_name: lidar

profiles

display_name: profiles

raclets

display_name: raclets

wind

display_name: wind

wolfgangpass

display_name: wolfgangpass

en: Wind LIDAR Davos Wolfgang


en: snow microstructure compression-experiments x-ray-tomography snow-mechanics

en: README

en: README file explaining the organization of the data

en: Snowmicroquakes Data

en: Compression experiments, X-ray images and simulation data with supplemented README file

en:
When snow is compressed with a certain speed, micro-snowquakes are triggered in the porous structure of bonded crystals. The present dataset covers uniaxial compression experiments of snow at different strain rates and concurrent X-ray tomography imaging documenting this feature.

The experiments were conducted in a micro-compression stage operated in the X-ray tomography scanner in the SLF cold laboratory. The dataset comprises the compression force data of 17 compression experiments, the 3D image data from 4 X-ray tomography scans and the results of numerical simulations.

compression-experiments

display_name: compression-experiments

microstructure

display_name: microstructure

snow

display_name: snow

snow-mechanics

display_name: snow-mechanics

x-ray-tomography

display_name: x-ray-tomography

en: Compressive stick slip and snow-micro-quakes


maintainer: Jana von Freyberg

en: review plant-water-uptake root-zone ecohydrology stable-water-isotopes uncertainties endmember-mixing-models

en: Data set of MEE-20-04-264 (CSV)

en: Data set of MEE-20-04-264

en: The following two tables contain information about the data sources of the values reported in Table 1 and 2 in the paper “Plant and root-zone water isotopes are difficult to measure, explain, and predict: some practical recommendations for determining plant water sources” published in the journal ‘Methods in Ecology and Evolution’.

en: The following two tables contain information about the data sources of the values reported in Table 1 and 2 in the paper “Plant and root-zone water isotopes are difficult to measure, explain, and predict: some practical recommendations for determining plant water sources” published in the journal 'Methods in Ecology and Evolution'.

ecohydrology

display_name: ecohydrology

endmember-mixing-models

display_name: endmember-mixing-models

plant-water-uptake

display_name: plant-water-uptake

review

display_name: review

root-zone

display_name: root-zone

stable-water-isotopes

display_name: stable-water-isotopes

uncertainties

display_name: uncertainties

educ

en: Education, culture and sport

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: Data set of: Plant and root-zone water isotopes are difficult to measure, explain, and predict: some practical recommendations for determining plant water sources


maintainer: Matthias Haeni

en: relative-humidity par meteorology precipitation meteo long-term wind-speed swiss-forest-lab temperature climate-change

en: Site aerial photo (Alpthal)

en: Site aerial photo from the Alpthal forest station. Source: Google. 2016. Site aerial photo from the Alpthal forest station. Retrieved November 11, 2016, from https://www.google.ch/maps

en: Forest station data (ALB)

en: Data plot of the forest station (ALB)

en: Data overview for air temperature, relative humidity, precipitation, PAR, wind speed.

en: High quality meteorological data are needed for long-term forest ecosystem research, particularly in the light of global change. The long-term data series published here comprises almost 20 years of measurements for one meteorological station in Alpthal in Switzerland which is located within a natural coniferous forest (ALB) with Norway spruce (_Picea abies_; 180-230 yrs) as dominant tree species. The meteorological time series are presented in hourly time resolution of air temperature, relative humidity, precipitation, photosynthetically active radiation (PAR) and wind speed. Alpthal is part of the Long-term Forest Ecosystem Research Programme (LWF) established and maintained by the Swiss Federal Research Institute WSL.

climate-change

display_name: climate-change

long-term

display_name: long-term

meteo

display_name: meteo

meteorology

display_name: meteorology

par

display_name: par

precipitation

display_name: precipitation

relative-humidity

display_name: relative-humidity

swiss-forest-lab

display_name: swiss-forest-lab

temperature

display_name: temperature

wind-speed

display_name: wind-speed

en: Alpthal, Switzerland: Long-term forest meteorological data from the Long-term Forest Ecosystem Research Programme (LWF), from 1997 onwards


en: snow-height snow-profile snow snow-water-equivalent gcos

en: STATION METADATA

en: DATA ACCESS

en:
This dataset contains long-term snow water equivalent and corresponding snow depth data 11 observer sites in Switzerland between 1200 and 2500 m a.s.l. compiled for the Global Climate Observing System (GCOS) and supported by MeteoSwiss. Snow depth (cm) and snow water equivalent (mm) are manually recorded every 2 weeks since the 1947 (depending on station). The attached metadata file gives details for each station.
The measurement series agree with GCOS objectives according to the GCOS Implementation Plan: This inlcudes:
• Raw data are archived in the snow and avalanche database at SLF.
• Measuring techniques are traceable and documented as snow depth and snow water equivalent have in general remained the same since beginning up to now. When planning new systems or changes of existing systems in the future, their impact will be assessed prior to implementation.
• Historical data of these 11 stations have been digitized and all data have been quality controlled.
• Detailed metadata (location of measurements) are available.
• Data gaps for the two most important winter and spring dates were reconstructed based on a published SWE parameterization from co-located snow depth measurements.
• Public availability of the data has been ensured by publishing the data on the Envidat portal (https://www.envidat.ch/dataset/gcos-swe-data).

gcos

display_name: gcos

snow

display_name: snow

snow-height

display_name: snow-height

snow-profile

display_name: snow-profile

snow-water-equivalent

display_name: snow-water-equivalent

en: GCOS SWE data from 11 stations in Switzerland


maintainer: Athanasios Nenes

en: cloud-droplets wolfgangpass supersaturation cloud-modeling raclets sigma-w

en: Predicted cloud droplet numbers (kappa=0.1) Davos Wolfgang

en:
In-situ measurements of aerosol size distributions along with updraft velocities collected from a wind Doppler Lidar are coupled with a state-of-the art droplet activation parameterization (Morales and Nenes, 2014) to determine the cloud droplet number and maximum in-cloud supersaturation that can potentially form over the Davos Wolfgang station between February 24 and March 8 2019. For this, as a sensitivity test, a hygroscopicity parameter of 0.1 is assumed, which is the lower limit determined from the analysis carried out for Weissfluhjoch (https://www.envidat.ch/dataset/ccn-hygroscopicity-predicted-cloud-droplet-numbers-weissfluhjoch). The data file contains:

* Date and time (DD/MM/YYYY hh:mm:ss) in UTC
* The wind-lidar derived standard deviation of updraft velocities (sigma-w) in m/s, used to apply the parameterization employing a single characteristic velocity (Morales and Nenes, 2010)
* The maximum predicted cloud parcel supersaturation (Smax%)
* The total in-situ aerosol number concentration (Naer) in cmˉ³, measured by the SMPS
* The predicted cloud droplet numbers (Nd) in cmˉ³
* The activation fraction (%)

en: Predicted cloud droplet numbers (kappa=0.25) Weissfluhjoch

en:
In-situ measurements of aerosol size distributions along with updraft velocities collected from a wind Doppler Lidar are coupled with a state-of-the art droplet activation parameterization (Morales and Nenes, 2014) to determine the cloud droplet number and maximum in-cloud supersaturation that can potentially form over the Davos Wolfgang station between February 24 and March 8 2019. For this, as a sensitivity test, a hygroscopicity parameter of 0.25 is assumed, which is the upper limit determined from the analysis carried out for Weissfluhjoch (https://www.envidat.ch/dataset/ccn-hygroscopicity-predicted-cloud-droplet-numbers-weissfluhjoch). The data file contains:

* Date and time (DD/MM/YYYY hh:mm:ss) in UTC
* The wind-lidar derived standard deviation of updraft velocities (sigma-w) in m/s, used to apply the parameterization employing a single characteristic velocity (Morales and Nenes, 2010)
* The maximum predicted cloud parcel supersaturation (Smax%)
* The total in-situ aerosol number concentration (Naer) in cmˉ³, measured by the SMPS
* The predicted cloud droplet numbers (Nd) in cmˉ³
* The activation fraction (%)

en: Cloud droplet properties were predicted between February 24 and March 8 2019 for the measurement site Davos Wolfgang (1630 m a.s.l., LON: 9.853594, LAT: 46.835577). Droplet calculations are carried out with the physically based aerosol activation parameterization of Morales and Nenes (2014), employing the “characteristic velocity” approach of Morales and Nenes (2010). Aerosol size distribution observations required to predict the cloud droplet numbers and maximum in-cloud supersaturation are obtained from a Scanning Mobility Particle Size Spectrometer (SMPS) instrument deployed at Davos Wolfgang (https://www.envidat.ch/dataset/aerosol-data-davos-wolfgang). The required vertical velocity measurements are derived from the wind Doppler Lidar (https://www.envidat.ch/dataset/lidar-wind-profiler-data) deployed at the same station and are extracted from the first bin of the instrument, being 200 m above ground level. The hygroscopic properties of the particles measured at Davos Wolfgang could not be estimated, owing to a lack of concurrent CCN measurements. As a sensitivity test, droplet calculations are performed assuming two different values of the aerosol hygroscopicity parameter, 0.1 and 0.25, based on the analysis carried out for Weissfluhjoch. Additional information can be found in Section 2.3 [here](https://acp.copernicus.org/preprints/acp-2020-1036/).

cloud-droplets

display_name: cloud-droplets

cloud-modeling

display_name: cloud-modeling

raclets

display_name: raclets

sigma-w

display_name: sigma-w

supersaturation

display_name: supersaturation

wolfgangpass

display_name: wolfgangpass

educ

en: Education, culture and sport

en: Predicted cloud droplet numbers Davos Wolfgang


en: large-scale-urban-development-projects strategic-spatial-planning land-use-change spatial-planning strategic-projects land-use-transformations urban-transformations europe

en: QCA R script large-scale urban development projects Europe

en:
For the set up of this R script, we used the “QCA” (Duşa, 2019) and “SetMethods” (Oana and Schneider, 2018) R packages.

The following further resources were also used:
Dusa, A. (2019). QCA with R: A comprehensive resource. Springer: Berlin.
Schneider, C. Q., & Wagemann, C. (2012). Set-theoretic methods for the social sciences. A guide to qualitative comparative analysis. Cambridge: Cambridge University Press.
Thomann, E., Oana, I.-E., & Wittwer, S. (2018). Performing fuzzy- and crisp set QCA with R. A user-oriented beginner's guide. Retrieved from http://www.evathomann.com/links/qca-r-manual

en: QCA data set large-scale urban development projects

en: Please refer to the sections: 3. The data set lsUDPs: 3.1 Selection of cases and data collection; 3.2 Data management and operationalization in the Metadata for further details on this resource.

en:
Table of Content: 1. General context of the data set "lsUDPs" ; 2. Background and aims of the study using the data set lsUDPs; 3. The data set lsUDPs: 3.1 Selection of cases and data collection; 3.2 Data management and operationalisation

1. General context of the data set "lsUDPs"
The data set "lsUDPs" has been generated as part of the CONCUR research project (https://www.wsl.ch/en/projects/concur.html) led by Dr. Anna M. Hersperger and funded by the Swiss National Science Foundation (ERC TBS Consolidator Grant (ID: BSCGIO 157789) for the period 2016-2020. The CONCUR research project is interdisciplinary and aims to develop a scientific basis for adequately integrating spatial policies (in this case, strategic spatial plans) into quantitative land-change modelling approaches at the urban regional level. The first stage (2016-2017) of the CONCUR project focussed on 21 urban regions in Western Europe. The urban regions were selected through a multi-stage strategy for empirical research (see Hersperger, A. M., Grădinaru, S., Oliveira, E., Pagliarin, S., & Palka, G. (2019). Understanding strategic spatial planning to effectively guide development of urban regions. Cities, 94, 96–105. https://doi.org/10.1016/j.cities.2019.05.032 ).

2. Background and aims of the study using the data set lsUDPs
As part of the CONCUR project, a specific task was to examine the relationship between strategic spatial plans and the formulation and implementation (i.e. urban land change) of large-scale urban development projects in Western Europe.
Strategic urban projects are typically large-scale, prominent urban transformations implemented locally with the aim to stimulate urban growth, for instance in the form of urban renewals of deprived neighborhoods, waterfront renewals and transport infrastructures. While strategic urban projects are referred to in the literature with multiple terms, in the CONCOR project we call them large-scale urban development projects (lsUDPs).
Previous studies acknowledged both local and supra-local (or structural) factors impacting the context-specific implementation of lsUDPs. Local governance factors, such as institutional capacity, coordination among public and private actors and political leadership, intertwine with supra-local conditions, such as state re-scaling processes and devolution of state competencies in spatial planning, de-industrialisation and increasing social inequality. Hence, in implementing lsUDPs, multi-scalar factors act in combination.
Because the formulation and implementation of lsUDPs require multi-scalar coordination among coalitions of public and private actors over an extended period of time, they are generally linked to strategic spatial plans (SSPs). Strategic spatial plans convey collective visions and horizons of action negotiated among public and private actors at the local and/or regional level to steer future urban development, and can contain legally binding dispositions, but also indicative guidelines.
The key question remains as to what extent large-scale urban development projects and strategic spatial plans can be regarded as aligned. By alignment, or “concordance”, we mean that strategic projects are formulated and implemented as part of the strategic planning process (“high concordance”), or that the strategic role of projects is reconfirmed in (subsequent) strategic plans (“moderate concordance”). Lack of concordance is found when lsUDPs have been limitedly (or not at all) acknowledged in strategic spatial plans.
We assume that certain local and supra-local factors, characterising the development of the projects, foster (but not strictly “cause”) the degree of alignment between lsUPDs and SSPs. In this study, we empirically examine how, and to what extent, the concordance between 38 European large-scale urban development projects and strategic plans (outcome: CONCOR) has been enabled by five multi-scalar factors (or conditions): (i) the role of the national state (STATE), (ii) the role of (inter)national private actors (PRIVATE), (iii) the occurrence of supra-regional external events (EVENTS), (iv) the degree of transport connectivity (TRANSP), and (v) local resistance from civil society (RESIST). We adopted a (multi-data) case-based qualitative strategy for empirical research and applied the formalised procedure of within- and cross-case comparison offered by fuzzy-set Qualitative Comparative Analysis appropriate for the goal of this study. Based on set theory, QCA formally integrates contextual sensitivity to case specificities (within-case knowledge) with systematic comparative analysis (across-case knowledge).
The research question the data set has been created to reply to is the following: which conditions, and combinations of conditions, enable the concordance between large-scale urban development projects and strategic spatial plans?
The conditions (“independent variables”) considered are. STATE: the set of large-scale urban projects characterized by a high degree of state intervention and support in their formulation and implementation, PRIVATE: the set of large-scale urban projects characterized by a high degree of involvement of (inter)national private actors in their formulation and implementation, EVENTS: the set of large-scale strategic projects whose formulation and implementation have been strongly affected by unforeseen international events and/or global trends, TRANSP: the set of large-scale strategic projects with a high degree of road and/or transit connectivity, and RESIST: set of large-scale strategic projects whose realization has been characterized by resistances that have substantially delayed or modified the project implementation.
The outcome (“dependent variable”) under analysis is CONCOR: the set of large-scale urban projects having a high degree of concordance/alignment/integration with strategic spatial plans

3. The data set lsUDPs

   3.1 Selection of cases and data collection
To generate the current data set on large-scale urban development projects in European urban regions (data set "lsUDPs"), we identified 35 large-scale urban development projects in a sample of the 21 Western urban regions considered in the CONCUR project (see supra, Hersperger et al. 2019): Amsterdam, Barcelona, Copenhagen, Hamburg, Lyon, Manchester, Milan, Stockholm, Stuttgart. The criteria we followed to identify the 35 large-scale urban development projects are: geographical location, size (large-scale), site (located either in the city core or in the larger urban region) and urban function (e.g. housing, transportation infrastructures, service and knowledge economic functions). Employing these criteria facilitated the selection of diverse large-scale urban development projects while still ensuring sufficient comparability.
In 2016, we performed 47 in-depth interviews with experts in urban and regional planning and large-scale strategic projects and infrastructure (i.e. academics and practitioners) about the formulation, implementation and development (1990s–2010s) of each project in each of the 9 selected urban regions. On average, each interviewee answered questions on 3.1 large-scale urban development projects. Three cases were subdivided into two cases because a clear differentiation between specific implementation stages was identified by the interviewees (expansion of the Barcelona airport, cases “bcn_airport80-90” and “bcn_airport00-16”; realisation of Lyon Part-Dieu, cases “lyo_partdieu70-90” and “lyo_partdieu00-16”; MediaCityUK, cases “man_salfordquays80-00” and “man_mediacityuk00-16”). Therefore, from the initial 35 cases, the final number of analysed cases in the lsUDPs dataset is 38.

    3.2 The data set lsUDPs: Data management and operationalisation
Interviews were fully transcribed and analysed through MAXQDA (version 12.3, VERBI GmbH, Berlin, Germany), and intercoder agreement was evaluated on a sample of nine interviews. We also compiled “synthetic case descriptions” (SCD) for each case (totalling more than 160 SCDs) to spot potential inconsistencies among interviewees’ accounts and to facilitate completion of the “calibration table” for each case (see below). An online expert survey distributed to the interviewees (response rate 78%) helped systematise the information collected during the interviews. We also consulted both academic and gray literature on the case studies to check for possible ambiguity and inconsistencies in the interview data, and to solve discrepancies between our assigned set membership scores and questionnaire values. Site visits were also carried out to retrieve additional information on the selected cases.
For each case (i.e. each of the 38 selected large-scale urban development projects), we operationalised each condition (i.e. STATE, PRIVATE, EVENTS, TRANSP, RESIST) and the outcome (CONCOR) in terms of sets, for subsequent application of Qualitative Comparative Analysis. This process is called “calibration”; we used a number of indicators for each condition to qualitatively assess each large-scale project across the conditions. The case-based qualitative assessment was then transformed into fuzzy-set membership values. Fuzzy-set membership values range from 0 to 1, and should be conceived as “fundamentally interpretative tools” that “operationalize theoretical concepts in a way that enhances the dialogue between ideas and evidence” (Ragin 2000:162, in “Fuzzy-set Social Science”. Chicago: University Press). We employed a four-value fuzzy-set scale (0, 0.33, 0.67, 1) to “quantify” into set membership scores the individual histories of cases retrieved from interview data. Only the condition TRANSP was calibrated as a crisp-set (0, 1).
The translation of qualitative case-based information into numerical fuzzy-set membership values was iteratively performed by populating a calibration table following standard practices recently emerged in QCA when dealing with qualitative (interview) data.

europe

display_name: europe

land-use-change

display_name: land-use-change

land-use-transformations

display_name: land-use-transformations

large-scale-urban-development-projects

display_name: large-scale-urban-development-projects

spatial-planning

display_name: spatial-planning

strategic-projects

display_name: strategic-projects

strategic-spatial-planning

display_name: strategic-spatial-planning

urban-transformations

display_name: urban-transformations

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: lsUDPS Large-scale urban development projects in European urban regions


en: snow bifaciality winter-electricity photovoltaic alps

en:
Title: Monitoring data set at A1 (test-site of Totalp), years 2018-2022
Provider: ZHAW - EKZ
Edition: Y.Frischholz, Laboratory of Cryospheric Sciences, EPFL
Last edition: 17.01.2024
File name structure:
The test site contains 6 segments named from A to F. The six files provided in the data/ subfolder follow the same naming convention (e.g. for segment A, the file name is: “A1_A.csv”). Refer to the publication for further details on the setups of the segments.
File format:
All files are provided in the CSV format.
Column headings:
	•	timestamp (datetime64): time stamp in format “YYYY-MM-DD HH:mm:ss”, time-zone: UTC
	•	poa_front (double): front plane-of-array irradiation (W/m**2)
	•	poa_back (double): rear plane-of-array irradiation (W/m**2)
	•	mod_temp (double): module’s temperature (°C)
	•	P_AC (double): output AC power (W)
Preprocessing:
	Outliers:
	⁃	Quantiles Q1 and Q99 are computed for each variable
	⁃	Values below Q1 and above Q99 are considered outliers
	⁃	Outliers are replaced by NaNs.
	Missing data:
	⁃	Data holes of less than 3 hours are interpolated linearly for all variables
	⁃	Data holes of more than 3 hours are replaced using the monthly nan-mean of the considered hour if more than 50% of the qualifying data points are available. For instance, if the data point 2022-12-12 12:12:00, is missing for a given variable and is part of a data hole larger than 3 hours, then it is replaced by the mean of all data points with hour = 12 of the month of December 2022, if 50% of all the qualifying data points are not NaN. In case more than 50% of the qualifying points are missing, the data point remains as missing (NaN).
	Wiring losses :
	⁃	As described in [1] , the test-site setup caused abnormally large wiring losses, mainly due to the distance to optimisers and to the low installed power per DC-wire.
	⁃	The wiring losses comprised between 10% and 15%, are averaged hourly and added to the measured DC power.

	Misc.:
	⁃	P_AC is computed for each segment based on the measured DC power and the average inverter’s efficiency (96.1%).
	⁃	As described in [1], the peak power of the installed module, used to compute the final yield is slightly different from the values announced by the manufacturer.
Mean uptime:
	Raw:
	⁃	95.2%
	Processed:
	⁃	100%
References:
[1] 	D. Anderegg, S. Strebel, and J. Rohrer, “Alpine Photovoltaik Versuchsanlage Davos Totalp : Erkenntnisse aus 5 Jahren Betrieb,” de, Sep. 	2023, Accepted: 2023-09-29T09:13:16Z Publisher: ZHAW Zürcher Hochschule für Angewandte Wissenschaften.DOI: 10.21256/	zhaw-2524. [Online]. Available: https://digitalcollection.zhaw.ch/handle/11475/28797 (visited on 12/15/2023).

en:
Title: Monitoring data set at A2 (utility-scale power-plant Muttsee), months 10.2022-09.2023
Provider: AXPO - IWB Industrielle Werke Basel
Last edition: 17.01.2024
Editor: Y.Frischholz, Laboratory of Cryospheric Sciences, EPFL
File name structure:
The power-plant is made of 23 string boxes (GAK) and inverters (WR) named after their given number. One file per device is provided in the data/ subfolder, following the same naming convention (e.g. for the string box number 1, the file name is: “A2_GAK01.csv” and for the corresponding inverter, the file name is “A2_WR01.csv”). Refer to the publication for further details on the setup of the power plant.
File format:
All files are provided in the CSV format.
Column headings:
	String boxes and inverters (GAK & WR):
	⁃	device_name (string): name of the device (same as file name)
	⁃	timestamp (datetime64): time stamp in format “YYYY-MM-DD HH:mm:ss”, time-zone: UTC
	String boxes (GAK):
	⁃	I_ (double): input current from the substring number (W)
	⁃	I_SUM (double): output current of string box (A)
	⁃	U_DC (double): output voltage of string box (V)
	⁃	P_DC_ (double): input DC power from the substring number (W)
	⁃	P_DC (double): output DC power of string box (W)
	⁃	$S$_T#_$T$ (double): temperature from the sensor connected to the string box (empty if not existing), placed on the “front” or “back” side (S) of table T. Two types of temperature measurements (#) are available: 1=standard cell temperature (°C) , 2=module temperature on the rear side (°C) .
	⁃	$S$_SRAD_T (double): poa irradiation (W/m**2) from the sensor connected to the string box (empty if not existing), placed on the “front” or “back” side (S) of table T.
		Inverters (WR):
	⁃	I_DC (double): input DC current(A)
	⁃	U_DC(double): input DC voltage(V)
	⁃	P_DC (double): input DC power (W)
	⁃	P_AC (double): output AC power (W)
Preprocessing:
	1. Outliers:
	⁃	Quantiles Q1 and Q99 are computed for each variable
	⁃	Values below Q1 and above Q99 are considered outliers
	⁃	Outliers are replaced by NaNs.

	2. Missing data:
	⁃	Data holes of less or equal to 3 hours are interpolated linearly for all variables
	⁃	Data holes of more than 3 hours are replaced using the monthly nan-mean of the considered hour if more than 50% of the qualifying data points are available. For instance, if the data point 2022-12-12 12:12:00, is missing for a given variable and is part of a data hole larger than 3 hours, then it is replaced by the mean of all data points with hour = 12 of the month of December 2022, if 50% of all the qualifying data points are not NaN. In case more than 50% of the qualifying points are missing, the data point remains as missing (NaN).
	3. Wiring losses:
	⁃	To be consistent with A1, wiring losses are corrected at A2. The wiring loss between the string boxes and the inverters is removed by multiplying the value of input P_DC at the inverter level (P_DC,inv) by the mean ratio P_DC,inv / P_DC,arr.
	⁃	The computed mean wiring loss is 2.3\%. It is computed from 2023-02-01 to 2023-09-30, after the long data hole in the data sets of the string boxes.

Mean uptime:
	Raw:
	⁃	WR: 98.2%
	⁃	GAK*: 38.5%
	Processed:
	⁃	WR: 99.6%
	⁃	GAK*: 56.4%

	*The uptime at the string box level (GAK) is low because PMUs at this level shut down during steady and low signal leading to unavailable data at night. In addition, the 23 days downtime of 	January 2023 could not be interpolated nor replaced.

en:
On this repository you can find the monitoring data of the 3 PV power-plants analysed in the article _"Confirmation of the power gain for solar photovoltaic systems in alpine areas"_ (doi: 10.3389/fenrg.2024.1372680) . Each folder contains the following two elements:
1. **README.txt** : describes the content of the folder. Especially it describes the plant's monitoring system's architecture and relates it to the various files included in the data sub-folder. It also provides a detailed description of all processing steps leading to the data sets as available in the data sub-folder and used in the pre-cited article.
3. **data/** : sub-folder containing the file(s) used in the referenced article.

alps

display_name: alps

bifaciality

display_name: bifaciality

photovoltaic

display_name: photovoltaic

snow

display_name: snow

winter-electricity

display_name: winter-electricity

en: Monitoring data sets of alpine photovoltaic power-plants


en: weissfluhjoch snow-temperature snow-stratigraphy ice-layers water-front snowmicropen

en: README

en: WFJ_ICE_LAYERS dataset

en: The WFJ_ICE_LAYERS dataset contains multi-instrument snowpack measurements at high temporal resolution, which enable to monitor the formation of deep ice layers due to preferential water flow, at the Weissfluhjoch research site, Davos, Switzerland. It covers the winter 2016/2017, with a focus on the early melting season. This dataset includes traditional snowpack profiles (weekly resolution, 15/11/2016-29/05/2017), SnowMicroPen penetration resistance profiles (daily resolution, 01/02/2017-19/04/2017), snow temperatures measured at different heights in the snowpack (half-hourly resolution, 01/03/2017-15/04/2017) and the water front height derived from an upward-looking ground penetrating radar (3-hour resolution, 04/03/2017-08/04/2017). The measurements are complemented by initialization files for SNOWPACK model simulations with the ice reservoir parameterization at Weissfluhjoch for the winter 2016/2017.

ice-layers

display_name: ice-layers

snow-stratigraphy

display_name: snow-stratigraphy

snow-temperature

display_name: snow-temperature

snowmicropen

display_name: snowmicropen

water-front

display_name: water-front

weissfluhjoch

display_name: weissfluhjoch

en: WFJ_ICE_LAYERS: Multi-instrument data for monitoring deep ice layer formation in an alpine snowpack


maintainer: Thorsten Bartels-Rausch

en: ozone chemistry metamorphism laboratory-study interface antarctica alpine snow solution heterogeneous brine arctic reaction

en: data list

en: Lists file names, snow sample properties, and flow settings for each data-set.

en: Data Figure 1

en: Data of published Figure

en: Matlab Script to view and plot data

en: Acetone data

en:
intensity of the acetone-water-cluster and water-cluster (as derived by a chemical ionisation mass spectrometer) with time in the carrier gas downstream of packed bed flow tube holding the snow sample or the by-pass, respectively. Time "0" denotes the time when the mass spectrometer data acquisition was started. When the carrier
gas with acetone was passed via the packed bed flow tube, that is switched from by-pass to pass the snow, acetone concentration in the carrier gas rapidly dropped due to surface adsorption and slowly recovered as the adsorption sites saturate. From this, the surface area can be obtained.

en: Readme file

en: This file shows data, code, and plots.

en: Ozone data

en: Trend of ozone mixing ratio ( _O3mixingRatio_ppb_ with time ( _time_s_ ) as measured downstream of the snow sample during the experiments. Time "0" denotes the time when data acquisition with ozone analyser was started. And, ozone (_nOzone_molec_per_s_ ) loss for each experiment with duration of ozone exposure ( _duration_s_ ) of ozone exposure, as derived from the ozone trends shown above. Time "0" denotes the time when the carrier gas with ozone was passed via the snow sample.

en: Matlab Data

en: All data as Matlab mat file

en: Earth’s snow cover is very dynamic on diurnal time scales. The changes to the snow structure during this metamorphism have wide ranging impacts such as on avalanche formation and on the capacity of surface snow to exchange trace gases with the atmosphere. Here, we investigate the influence of dry metamorphism, which involves fluxes of water vapor, on the chemical reactivity of bromide in the snow. For this, the heterogeneous reactive loss of ozone at a concentration of 5-6E12 molecules cm-3 is investigated in artificial, shock-frozen snow samples doped with 6.2 uM sodium bromide and with varying metamorphism history. The oxidation of bromide in snow is one reaction initiating polar bromine releases and ozone depletions.

alpine

display_name: alpine

antarctica

display_name: antarctica

arctic

display_name: arctic

brine

display_name: brine

chemistry

display_name: chemistry

heterogeneous

display_name: heterogeneous

interface

display_name: interface

laboratory-study

display_name: laboratory-study

metamorphism

display_name: metamorphism

ozone

display_name: ozone

reaction

display_name: reaction

solution

display_name: solution

educ

en: Education, culture and sport

en: Data set on bromide oxidation by ozone in snow during metamorphism from laboratory study


en: snow-depth-distribution dischma photogrammetry davos snow-hydrology avalanches

en: Snowdepth maps

en:
The available datasets are snow depth maps with a spatial resolution of 0.5 m derived from images of the survey camera Vexcel Ultracam mounted on a piloted airplane. Image acquisition was carried out during the approximately peak of winter (time when the thickest snowpack is expected) in spring. The snow depth maps are calculated by the subtraction of a summer-DTM from the processed winter- DSM of the corresponding date. The summer-DTM used was derived from a point cloud of an airborne laser scanner from 2020.

Due to the occurrence of inaccuracies of the calculated snow depth values caused by the photogrammetric method, we applied different masks to significantly increase the reliability of the snow depth maps. We masked out settled areas, high-frequented streets and technical constructions, pixels with high vegetation (height > 0.5 m) , outliers and unrealistic snow depth values. In addition, we modified the snow depth values of snow-free pixels to 0.
The information on buildings and infrastructure comes from the exactly classified ALS point cloud and the TLM dataset from Swisstopo (https://www.swisstopo.admin.ch/de/geodata/landscape/tlm3d.html#links). High vegetation is also derived from the classification and the calculated object height from the point cloud.
Outliers and unrealistic snow depth values are defined as negative snow depth values and snow depths exceeding 10 m. The classification of each pixel of the corresponding orthophoto into snow-covered or snow-free is based on the application of a threshold of the NDSI or manually determined ratios of the RGB values.

An extensive accuracy assessment proves the high accuracy of the snow depth maps with a root mean square error of 0.25 m for the year 2017 and 0.15 m for the following snow depth maps.

The work is published in:

avalanches

display_name: avalanches

davos

display_name: davos

dischma

display_name: dischma

photogrammetry

display_name: photogrammetry

snow-depth-distribution

display_name: snow-depth-distribution

snow-hydrology

display_name: snow-hydrology

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: Snow depth mapping by airplane photogrammetry (2017 -  ongoing)


maintainer: Marco Moretti

en: beekeeping resource-availability urban-biodiversity pollinator-experiment urbanization urban-ecosystems zurich wild-bees gardens honeybees bettergardens city4bees

en: Response and predictors used for the SEMs

en:
The data contains the following columns:

  SiteID: numeric, the identity of the garden where the bee was sampled.
  Taxonname: character, species name
  Lecty: numeric discreet, a mesure of specialisation degree. Levels: 1 = monolectic; 2=oliolectic; 3=polilectic
  Pheno.start= numeric discreet, the starting week of the flying activity.
  Pheno.end= numeric discreet, the ending week of the flying activity.
  Pheno.duration=numeric discreet, Pheno.end - Pheno.start
  Daytime.activity = numeric continuous, individual-level measure of the day hour when the bee was sampled
  ITD = numeric continuous, individual-level measure of the InterTegular Distance, a metric of mobility in mm.
  Rel.tongue.length =numeric continuous, individual-level measure of the relative tongue length (Tongue length / ITD), a metric of specilaisation degree, in mm.

en: Metadata for the predictor and response dataset

en: Metadata for the predictors and response dataset

en:
Mean, standard deviation , minimum and maximum values of six functional traits. The data has the following structure:
- Bee_species: bee scientific name
- mean_trait: mean value
- sd_trait: standard deviation
_min_trait: minimum value
- max_trait: maximum value
- trait: the six traits used. ITD = Intertegular distance (mm); Pheno.duration = duration of the phenology; Pheno.start = start of the phenology; Pheno.end = end of the phenology; Rel.tongue.length= relative tongue length (mm); Daytime.activity = daily activity (h)
DistNichePart: functional dissimilarity in a multidimentional trait space defined by five traits between wild bee individuals of a wild bee species and the honeybee individuals. Values are at the species level.

en:
Cities are socio-ecological systems that filter and select species, thus establishing unique species assemblages and biotic interactions. Urban ecosystems can host richer wild bee communities than highly intensified agricultural areas, specifically in resource-rich urban green spaces such as allotment and family gardens. At the same time, urban beekeeping has boomed in many European cities, raising concerns that the fast addition of a large number of managed bees could deplete the existing floral resources, triggering competition between wild bees and honeybees. The data has been used to investigated the interplay between resource availability and the number of honeybees at local and landscape scales and how this relationship influences wild bee diversity.

This dataset contains the raw and processed data supporting the findings from the paper: "Low resource availability drives feeding niche partitioning between wild bees and honeybees in a European city".

The data contains:
1. Bee trait measurements at the species and individual-level of five functional traits.
2. The values of the feeding niche partitioning (functional dissimilarity to honeybees)
3. The predictors of resource availability and beekeeping intensity at local and landscape scales used in the modelling of the paper for the 23 experimental sites.

beekeeping

display_name: beekeeping

bettergardens

display_name: bettergardens

gardens

display_name: gardens

honeybees

display_name: honeybees

pollinator-experiment

display_name: pollinator-experiment

resource-availability

display_name: resource-availability

urban-biodiversity

display_name: urban-biodiversity

urban-ecosystems

display_name: urban-ecosystems

urbanization

display_name: urbanization

wild-bees

display_name: wild-bees

zurich

display_name: zurich

en: Niche partitioning between wild bees and honeybees


maintainer: Thomas Wohlgemuth

en: biogeography pairwise-stand-comparisons biodiversity forest-management soil-impacts

en: headers

en: Description of headers for data_wohlgemuth_etal_Neobiota_2022

en: Baseline data

en: references

en: Bibliography of all references cited in data_wohlgemuth_etal_Neobiota_2022.

en: Compiled data on the impacts of seven important NNTs (Acacia dealbata, Ailanthus altissima, Eucalyptus globulus, Prunus serotina, Pseudotsuga menziesii, Quercus rubra, Robinia pseudoacacia) on physical and chemical soil and biodiversity in Europe, and summarise commonalities and differences. A total of 107 publications considered, studies referred to biodiversity attributes and soil properties: 2804 lines and 30 rows.

biodiversity

display_name: biodiversity

biogeography

display_name: biogeography

forest-management

display_name: forest-management

pairwise-stand-comparisons

display_name: pairwise-stand-comparisons

soil-impacts

display_name: soil-impacts

en: Impact of non-native tree species in Europe on soil properties and biodiversity: a review


en: sessile-species swisslichens detection-probability detectability occupancy-model cryptogams biodiversity monitoring lichens inter-observer-difference bayesian-inference observer-error

en: Repository containing the full data, code, README and workflow files.

en:
The available lichen data consists of detection/nondetection data (1/0) of 373 tree-inhabiting (*corticolous*) lichen species from 416 plots surveyed 1-2 times. The lichen data were originally collected for the purpose of the Red List of epiphytic lichen species in Switzerland ([Scheidegger *et al.* 2002](https://www.bafu.admin.ch/bafu/de/home/themen/biodiversitaet/publikationen-studien/publikationen/rote-liste-gefaehrdete-arten-baum-erdbewohnende-flechten.html)), but updated to recent nomenclature for the purpose of this study.
This repository contains all the supporting data and R code for the paper:
von Hirschheydt, G., Kéry, M., Ekman, S., Stofer, S., Dietrich, M., Keller, C., Scheidegger, C. (2024) **Occupancy model reveals limited detectability of lichens in a standardised large-scale monitoring**. *Journal of Vegetation Science*.
Results and figures presented in the manuscript should be reproducible (with small differences in the latter digits due to stochasticity of the MCMC sampler) with the provided data and code.
The downloadable `.zip` folder has the following structure:
* `0_data/`
* `1_code/`
* `2_output/`
* `lichen_detectability.Rproj`
* `README.txt`
* `workflow.html`
- `workflow.Rmd`

The main folder and the three subordinate folders each have their own `README*.txt` file. These describe each available file in detail and should be consulted prior to using the data or running any code. The file `lichen_detectability.Rproj` stores the information about the R project. The user can open the project by clicking/double-clicking on this file which will automatically define the repository as working directory for the R session. If the user does not use RStudio/Posit, they may have to set the working directory manually to the stored location in the R files. The files `workflow.*` guide the user through the analysis (`1_code/*.R`) in the correct order so that they can:
- bundle the cleaned data into a data list readable for JAGS
- fit the multi-species occupancy model to the data and store the output
- assess the goodness-of-fit of the model to the data
- conduct a prior sensitivity analysis with 2 additional sets of priors
- extract the summary statistics reported in the manuscript and supplementary materials
- generate the figures shown in the manuscript and supplementary materials

bayesian-inference

display_name: bayesian-inference

cryptogams

display_name: cryptogams

detectability

display_name: detectability

detection-probability

display_name: detection-probability

inter-observer-difference

display_name: inter-observer-difference

lichens

display_name: lichens

monitoring

display_name: monitoring

observer-error

display_name: observer-error

occupancy-model

display_name: occupancy-model

sessile-species

display_name: sessile-species

swisslichens

display_name: swisslichens

educ

en: Education, culture and sport

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: Repeated detection-nondetection data of corticolous lichens from a standardised monitoring across Switzerland


swiss-fluxnet-site-davos

title_for_slug: swiss-fluxnet-site-davos

en: greenhouse-gas flux forest swiss-forest-lab icos meteorological-measurements eddy-covariance swiss-fluxnet

en: Fluxnet2015 dataset

en: Processed flux and meteo data are also part of the Fluxnet2015 dataset.

en: Site description

en: Data access

en: The flux and meteo data of the Swiss FluxNet site Davos are openly available. Near real-time flux and meteo data are uploaded daily to the ICOS Carbon Portal.

en: Processed data

en: Processed flux and meteo data are available from the European Fluxes Database Cluster.

en:
The Swiss FluxNet Site Davos is a managed subalpine evergreen forest, located on the Seehorn mountain near Davos in the Swiss Alps. The site is dominated by Norway spruce. The tower is owned by the Federal Office for the Environment (FOEN).
Ecosystem flux measurements of CO2, H2O (since 1997) as well as CH4 and N2O (since 2016) are performed with the eddy covariance method.
In addition to Swiss FluxNet, the site is part of the National Air Pollution Monitoring Network (NABEL), the Long term Forest Ecosystem Research (LWF), the biological drought and growth indicator network (TreeNet) and of ICOS Switzerland (Integrated Carbon Observation System). Since November 2019, the site is an ICOS Class 1 Ecosystem station.

Measurements

- Ecosystem flux measurements of CO2, H2O vapour (since 1997) as well a CH4 and N2O (since 2016) are performed with the eddy-covariance method. This method is based on measurements of trace gas mixing ratios, using infrared gas analyzers (for CO2, H2O vapor) and laser spectrometers (for CH4 and N2O), combined with wind speed and wind direction measurements, using 3D sonic anemometers. To resolve the short-term turbulent fluctuations in the atmosphere, very fast measurements are needed: we measure at 10-20 Hz, i.e., 10-20 times per second. To assess the energy budget of each ecosystem, also radiation sensors and soil climate profiles are installed at the site.
- Sub-canopy eddy fluxes (CO2, H2O, since 2023 also CH4).
- Continuous profile concentration and forest floor flux measurement of CO2, H2O, CH4, N2O.
- Auxiliary micrometeorology and soil climate measurements.

Data availability

Near real-time flux and meteo data uploaded daily to the ICOS Carbon Portal. Processed flux and meteo data are also available from the European Fluxes Database Cluster and part of Fluxnet2015 dataset.

Data policy

ICOS data license:
[https://www.icos-cp.eu/data-services/about-data-portal/data-license](https://www.icos-cp.eu/data-services/about-data-portal/data-license)

Detailed site info:
[https://www.swissfluxnet.ethz.ch/index.php/sites/ch-dav-davos/site-info-ch-dav/](https://www.swissfluxnet.ethz.ch/index.php/sites/ch-dav-davos/site-info-ch-dav/)

eddy-covariance

display_name: eddy-covariance

flux

display_name: flux

forest

display_name: forest

greenhouse-gas

display_name: greenhouse-gas

icos

display_name: icos

meteorological-measurements

display_name: meteorological-measurements

swiss-fluxnet

display_name: swiss-fluxnet

swiss-forest-lab

display_name: swiss-forest-lab

en: Swiss FluxNet Site Davos


maintainer: Henning Löwe

en: unconfined-compression-experiments 3d-ct-images discrete-element-modelling spherical-model-snow microstructure snow-mechanics

en: Data Structure (Python Notebook)

en: Data Access

en: Data Structure (Python Notebook - view online)

en:
For the investigation of microstructural and mechanical properties of snow unconfined compression experiments and 3D computed tomography (CT) imaging were performed on sintered rounded grain snow and spherical model snow. The spherical model snow was generated to create geometrically simplified, well-defined microstructures for calibration of numerical models, such as discrete element models (DEM) in which the microstructure is represented by spherical particles.
In the experiments, microstructural variation was created by varying the sintering time (contact size) and the density of the ice sphere samples (number of contacts). The 3D CT images allow for a complete reconstruction of the entire experimental sample (cylindrical sample dimension: diameter = 33.6 mm; height = 14 mm).

discrete-element-modelling

display_name: discrete-element-modelling

microstructure

display_name: microstructure

snow-mechanics

display_name: snow-mechanics

spherical-model-snow

display_name: spherical-model-snow

unconfined-compression-experiments

display_name: unconfined-compression-experiments

en: Unconfined compression experiments and 3D CT images of spherical model snow and RG snow samples