en: terrestrial-laser-scanning riegl-vz6000 patchy-snow-covers tls snow-ablation-rates

en: Snowmask 2015

en: Digital Elevation Modell 2015

en: Snowmask 2014

en: Digital Elevation Modell 2016

en: Snowmask 2016

en: Gletschboden test site

en: Digital Elevation Modell 2014

en: We recorded snow ablation maps with a terrestrial laser scanner (TLS, Riegl-VZ6000) at the Gletschboden area. The TLS position is located approximately 30 vertical meters above the Gletschboden area at a northerly exposed slope. In total 44 TLS measurement sets have been conducted in three consecutive years 2014-2016 (2014: 13 measurements; 2015: 17 measurements; 2016: 14 measurements). The TLS system has a single-point measurement frequency of 300 kHz and a beam divergence of 0.007°. This set-up allows a horizontal resolution of approximately 0.01 m in 100 m distance to the TLS position. One scan of the Gletschboden area lasts approximately 15 minutes. The travel time from the laser scanner towards the surface is recorded and afterwards converted into a point cloud of distances. 5 reflectors located at the Gletschboden area and in the closer surroundings were additionally scanned during each measurement to transform the point cloud from the scanner own coordinate system into Swiss coordinates. Additionally, orthophotos have been created by using pictures recorded from the TLS in order to provide snow mask maps. Snow and bare ground can be distinguished by the RGB color information of the orthophoto. Cells with blue band information greater than 175 were categorized as snow and all cells with values smaller or equal 175 were categorized as bare ground.

patchy-snow-covers

display_name: patchy-snow-covers

snow-ablation-rates

display_name: snow-ablation-rates

terrestrial-laser-scanning

display_name: terrestrial-laser-scanning

tls

display_name: tls

en: DISCHMEX - High-resolution daily snow ablation rates in an Alpine environment


maintainer: Esther Frei

en: long-term-experiment mountain-ecology literature-review treeline-ecosystems stillberg

state: active

type: dataset

en: The Stillberg bibliography (Stillberg_bibliography_v1.zip) comprises a comprehensive list of 276 scientific publications, 91 of them published in peer-reviewed ISI journals (Stillberg_bibliography_data_v1.csv) along with the metadata file (Stillberg_bibliography_metadata_v1.csv). Currently the bibliography comprises literature about the main afforestation experiment, the FACE × warming experiment, the nutrient addition experiment, and the G-TREE experiment, as well as further publications related to the Stillberg research site that have been published until August 2023. The bibliography can be filtered for different categories, e.g., experiment, peer-review, source repository or database, and source title.

format: SERVICE

en:
 Background information

The Stillberg ecological treeline research site in the Swiss Alps was established in 1975, with the aim to develop ecologically, technically, and economically sustainable reforestation techniques at the treeline to reduce the risk of snow avalanches. In the course of time, additional research aspects gained importance, such as the ecology of the treeline ecotone under global change. Over almost fifty years, research at the Stillberg site combined long-term monitoring of the large-scale high-elevation afforestation with experimental manipulations simulating global change impacts. Besides providing a scientific basis and practical guidelines for high-elevation afforestation, this research has contributed to a comprehensive understanding of ecological processes in the treeline ecotone across different compartments and scales, from individual trees, non-tree vegetation and soils to whole ecosystems, in the context of global change resulting in more than 150 publications.

 Dataset generation

We compiled a comprehensive list of scientific publications covering research at the Stillberg research site by conducting searches in the literature databases Web of Science and Google Scholar, as well as in the Digital Object Repository of the Swiss Federal Institute for Forest, Snow and Landscape Research WSL (DORA). We compiled all publications about the afforestation experiment, the FACE × warming experiment, the nutrient addition experiment, the G-TREE experiment, as well as other studies related to the Stillberg research site.

 Data description

The Stillberg bibliography (Stillberg_bibliography_data_v1.csv) comprises a comprehensive list of 276 scientific publications, 91 of them published in peer-reviewed ISI journals. Currently the bibliography comprises literature about the main afforestation experiment, the FACE × warming experiment, the nutrient addition experiment, and the G-TREE experiment, as well as further publications related to the Stillberg research site that have been published until August 2023. The bibliography can be filtered for different categories, e.g., experiment, peer-review, source repository or database, and source title. The bibliography is described in a metadata file (Stillberg_bibliography_metadata_v1.csv). The bibliography along with the metadata file are provided in a ZIP-folder (Stillberg_bibliography_v1.zip).

literature-review

display_name: literature-review

long-term-experiment

display_name: long-term-experiment

mountain-ecology

display_name: mountain-ecology

stillberg

display_name: stillberg

treeline-ecosystems

display_name: treeline-ecosystems

educ

fr: Éducation, culture et sport

de: Bildung, Kultur und Sport

en: Education, culture and sport

it: Istruzione, cultura e sport

envidat

fr: EnviDat: le portail de données environnementales

de: EnviDat: das Umwelt-Datenportal

en: EnviDat: the Environmental Data Portal

it: EnviDat: il portale dei dati ambientali

fr: EnviDat est le portail de données du WSL; il offre un accès uniformisé et réglementé aux données de surveillance et de recherche en matière d’environnement. Ce portail est capable d’héberger et de publier des ensembles de données précieuses et uniques, qui sont partagées aux quatre coins de la planète. Ce faisant, EnviDat favorise la recherche et contribue à l’avancement des sciences environnementales.

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

de: EnviDat ist das Datenportal der WSL für einen einheitlichen und verwalteten Zugang zu Umweltdaten aus Monitoring- und Forschungsprojekten. Auf dem Portal können Datensätze gehostet und veröffentlicht werden. Durch die weltweite Bereitstellung einzigartiger und wertvoller Datensätze leistet EnviDat einen Beitrag zur Forschung im Bereich der Umweltwissenschaften.

it: EnviDat è il portale dati del WSL che fornisce un accesso unificato e gestito ai dati di monitoraggio ambientale e di ricerca. Il portale ha la capacità di ospitare e pubblicare serie di dati preziosi e unici che vengono condivisi in tutto il mondo. Così facendo, EnviDat promuove la ricerca e contribuisce al progresso della scienza ambientale.

political_level: other

wsl

capacity: public

type: organization

approval_status: approved

key: guid

key: uri

value: Envidat Harvester

en: Bibliography of the long-term treeline research site Stillberg, Switzerland


greenland-climate-network-gc-net-data

maintainer: EnviDat Support

title_for_slug: greenland-climate-network-gc-net-data

en: climate automatic-weather-station greenland aws air-temperature net-radiation

en: Archived GC-Net Data (deprecated)

en:
The GC-Net is kindly continued by the Geological Survey of Denmark and Greenland (GEUS).

Starting October 3, 2022, the access to the latest versions of the "ready to use" L1 data has been migrated to GEUS, (doi:10.22008/FK2/VVXGUT). Future versions will be available from GEUS, while the initial versions of L0 and L1 data have been archived.

en: Access the latest L1 data

en:
The GC-Net is kindly continued by the Geological Survey of Denmark and Greenland (GEUS).

Starting October 3, 2022, the access to the latest versions of the "ready to use" L1 data has been migrated to GEUS, (doi:10.22008/FK2/VVXGUT). Future versions will be available from GEUS, while the initial version of L1 data has been archived.

en: GC Net Config for Stations

media_type: application/json

en: Stations Config from the static bucket

format: JSON

en: 22-Petermann ELA

en: GC Net Chart Parameters

en: Stations parameters from static bucket

en:
In Memory of Dr. Konrad (Koni) Steffen

Update October 2022: The GC-Net is kindly continued by the Geological Survey of Denmark and Greenland (GEUS).
Starting October 3, 2022, the access to the latest versions of the "ready to use" L1 data has been migrated to GEUS. Future data versions will be available at: [https://doi.org/10.22008/FK2/VVXGUT](https://doi.org/10.22008/FK2/VVXGUT)
 Background
Starting with a single station in 1991, the Greenland Climate Network (commonly known as GC-Net) is a set of Automatic Weather Stations (AWS) set up and managed by the late Prof. Dr. Konrad (Koni) Steffen, and spanning the Greenland Ice Sheet (GrIS). This first station was "Swiss Camp" or the "ETH-CU" camp (GC-Net station 01) which was used as a field science and education site by Koni for years. The GC-Net was expanded with multiple NASA, NOAA, and NSF grants throughout the years, and then supported by WSL in the later years. These data (see "C-file" below) were previously hosted by the Cooperative Institute for Research in Environmental Sciences (CIRES) in Boulder, Colorado.

 Overview
Provided in this dataset are the 16 longest running stations in the network, which are spread over a significant area of the GrIS and the majority of the unique climatic zones. From the South Dome high point in the South, to the Western Jakobshavn ablation region in the west, to the Petermann glacier in the North across east of the Northeast Greenland Ice Stream to the east, GC-Net is the longest running climatological record of Greenland.

 The standard GC-Net station consists of:
* Air temperature measurements at 2 heights above the surface
* Temperature and humidity measurements at 2 heights above the surface
* Wind speed and direction measured at 2 heights above the surface
* Sonic distance sounder measurements for 2 snow height and distance of instruments to surface
* Incoming shortwave radiation measurement
* Reflected shortwave radiation measurement
* Net broadband radiation (long- and short-wave) measurement
* Air pressure measurement
Data have often been repatriated in near-real time using one of either the GOES geostationary satellite or the ARGOS polar orbiting satellite transmission system. The stations were visited typically every 1-2 years for maintenance and service, and to download full uncorrupted data directly from the dataloggers. GC-Net stations were visited by Twin Otter equipped with snow skids to land directly on the open-ice at the AWS locations, or by helicopter near the west coast. The AWSs operate on solar and battery power and occasionally lost power during the dark and cold winter months, particularly when the batteries were aging.

 Dataset
This dataset consists of 2 main data levels; Level 0 and Level 1.
Level 0 is the raw data from the dataloggers, historical processing codes, satellite transmissions, and Koni’s personal data archive. Level 0 data (.zip) directories contain subdirectories:
* “C file” - contains the historical processed datafile for each station.
* “Campbell logger files” - contains the raw csv datafiles from the stations’ Campbell Scientific dataloggers since the CR1000 era (~2007-2008 for most stations).
* “Photos” - contains photographs of the station when available marked by year.
Level 1 is the appended, calibrated, cleaned, and quality flagged data. The full processing scheme is open-source and publicly available on the following GitHub repository (please also check GitHub for the latest L1 data):
[GC-Net L1 data on GitHub](https://github.com/GEUS-Glaciology-and-Climate/GC-Net-level-1-data-processing "GC-Net-level-1-data-processing")
Level 1 data is provided in the newly described csv-compatible [NEAD format](https://www.envidat.ch/#/metadata/nead "NEAD format").

 Additional Details
Dataset description publication will be forthcoming.
The Geological Survey of Denmark and Greenland (GEUS) has been imperative in the reprocessing and continuity mission of GC-Net. Multiple GC-Net stations have been replaced with updated and upgraded AWS hardware at the same coordinates by GEUS. This effort will ensure continuity of the GC-Net dataset into the future.

air-temperature

display_name: air-temperature

automatic-weather-station

display_name: automatic-weather-station

aws

display_name: aws

climate

display_name: climate

greenland

display_name: greenland

net-radiation

display_name: net-radiation

en: Greenland Climate Network (GC-Net) Data


en: complex-terrain numerical-simulation wrf cosmo-wrf grayzone

media_type: application/zip

format: ZIP

en:
This dataset contains simulation data for *"Influence of Air Flow Features on Alpine Wind Energy Potential" (Kristianti et al., 2024).*
•	The WRF_dia2702 and WRF_dia1103 folders contain the namelist.wps, namelist.input, and output files from the simulation in the Diablerets region on 27/02/2021 and 11/03/2021, respectively.
•	The WRF_luk2310 and WRF_luk0912 folders contain the namelist.wps, namelist.input, and output files from the simulation in the Lukmanier region on 23/10/2020 and 09/12/2020, respectively.
•	The postprocessing file contains Python codes used to create figures in Kristianti et al. (2024).
**Notes:**
•	Topography input is provided by Gerber et al. (2021).
•	Simulations are run using the COSMO-WRF model developed by Gerber et al. (2018).
•	Visualization by Python code uses wrf-python provided by Ladwig et al. (2017).
*This dataset was produced by the EDGE consortium sponsored by the Swiss Federal Office of Energy's SWEET programme, Swiss National Science Foundation (SNSF): Grant 179130, and the Swiss National Supercomputing Centre (CSCS) projects s938, s1115 and s1242.*

complex-terrain

display_name: complex-terrain

cosmo-wrf

display_name: cosmo-wrf

grayzone

display_name: grayzone

numerical-simulation

display_name: numerical-simulation

wrf

display_name: wrf

en: COSMO-WRF Dataset for Swiss Alps Simulations in Gray-Zone Resolution


maintainer: Frank Techel

en: avalanche-accident-statistics avalanche-statistics long-term-trends avalanche-accident avalanche-fatalities

en: Data avalanche fatalities 1969/1970 - 2014/2015

media_type: text/plain

en: The data comprises avalanche fatality data from the Alpine regions in the seven countries Austria, France, Germany, Italy, Liechtenstein, Slovenia, and Switzerland.

format: TXT

mimetype: text/plain

en:
During the last 45 years, about 100 people lost their lives in avalanches in the European Alps each year. Avalanche fatalities in settlements and on transportation corridors have considerably decreased since the 1970s. In contrast, the number of avalanche fatalities during recreational activities away from avalanche-secured terrain doubled between the 1960s and 1980s and has remained relatively stable since, despite a continuing strong increase in winter backcountry recreational activities.

Data complementing Figure 2 in:
_"Avalanche fatalities in the European Alps: long-term trends and statistics"_, by Techel, F., Jarry, F., Kronthaler, G., Mitterer, S., Nairz, P., Pavšek, M., Valt, M., and Darms, G.

Data description:
please refer to section 2 (Data and Methods) in the mentioned publication

avalanche-accident

display_name: avalanche-accident

avalanche-accident-statistics

display_name: avalanche-accident-statistics

avalanche-fatalities

display_name: avalanche-fatalities

avalanche-statistics

display_name: avalanche-statistics

long-term-trends

display_name: long-term-trends

educ

en: Education, culture and sport

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: Avalanche fatalities in the European Alps (1969/1970 - 2014/2015)


en: alps findelengletscher griesgletscher sankt-annafirn dem uav dsm drone glacier gletscher orthoimage orthophoto

en:
This .zip folder contains:

 - An orthoimage (oi) of 0.1m resolution

- A Digital Surface Model (dsm) of 0.1m resolution

- The Agisoft Photoscan automatic processing report

for the UAV field campaign conducted on the Findelengletscher on the 15th of September 2015.

mimetype: application/zip

en:
This .zip folder contains:

 - An orthoimage (oi) of 0.1m resolution

- A Digital Surface Model (dsm) of 0.1m resolution

- The Agisoft Photoscan automatic processing report

for the UAV field campaign conducted on the Griesgletscher on the 15th of August 2015.

en:
This .zip folder contains:

 - An orthoimage (oi) of 0.1m resolution

- A Digital Surface Model (dsm) of 0.1m resolution

- The Agisoft Photoscan automatic processing report

for the UAV field campaign conducted on the Findelengletscher on the 2nd of July 2016.

en:
This .zip folder contains:

 - An orthoimage (oi) of 0.1m resolution

- A Digital Surface Model (dsm) of 0.1m resolution

- The Agisoft Photoscan automatic processing report

for the UAV field campaign conducted on the Findelengletscher on the 09th of April 2015.

en:
This .zip folder contains:

 - An orthoimage (oi) of 0.1m resolution

- A Digital Surface Model (dsm) of 0.1m resolution

- The Agisoft Photoscan automatic processing report

for the UAV field campaign conducted on the Sankt Annafirn on the 15th of April 2015.

en:
This .zip folder contains:

 - An orthoimage (oi) of 0.1m resolution

- A Digital Surface Model (dsm) of 0.1m resolution

- The Agisoft Photoscan automatic processing report

for the UAV field campaign conducted on the Sankt Annafirn on the 15th of July 2015.

en:
This .zip folder contains:

 - An orthoimage (oi) of 0.1m resolution

- A Digital Surface Model (dsm) of 0.1m resolution

- The Agisoft Photoscan automatic processing report

for the UAV field campaign conducted on the Findelengletscher on the 30th of August 2016.

en:
This .zip folder contains:

 - An orthoimage (oi) of 0.1m resolution

- A Digital Surface Model (dsm) of 0.1m resolution

- The Agisoft Photoscan automatic processing report

for the UAV field campaign conducted on the Griesgletscher on the 26th of September 2015.

en:
This .zip folder contains:

 - An orthoimage (oi) of 0.1m resolution

- A Digital Surface Model (dsm) of 0.1m resolution

- The Agisoft Photoscan automatic processing report

for the UAV field campaign conducted on the Griesgletscher on the 13th of September 2016.

en: Bulk Data Access

en: Link to the S3 bucket where all the data resources can be downloaded in bulk

en:
This .zip folder contains:

 - An orthoimage (oi) of 0.1m resolution

- A Digital Surface Model (dsm) of 0.1m resolution

- The Agisoft Photoscan automatic processing report

for the UAV field campaign conducted on the Findelengletscher on the 19th of April 2016.

media_type: application/pdf

en: This .pdf contains an orthoimage for each dataset as well as a Table which displays the number of flights made, image acquired, number of GCP set and the total area covered.

format: PDF

mimetype: application/pdf

en:
This .zip folder contains:

 - An orthoimage (oi) of 0.1m resolution

- A Digital Surface Model (dsm) of 0.1m resolution

- The Agisoft Photoscan automatic processing report

for the UAV field campaign conducted on the Findelengletscher on the 22th of September 2016.

en:
This .zip folder contains:

 - An orthoimage (oi) of 0.1m resolution

- A Digital Surface Model (dsm) of 0.1m resolution

- The Agisoft Photoscan automatic processing report

for the UAV field campaign conducted on the Findelengletscher on the 21th of July 2015.

en:
This .zip folder contains:

 - An orthoimage (oi) of 0.1m resolution

- A Digital Surface Model (dsm) of 0.1m resolution

- The Agisoft Photoscan automatic processing report

for the UAV field campaign conducted on the Sankt Annafirn on the 28th of September 2015.

en:
This .zip folder contains:

 - An orthoimage (oi) of 0.1m resolution

- A Digital Surface Model (dsm) of 0.1m resolution

- The Agisoft Photoscan automatic processing report

for the UAV field campaign conducted on the Griesgletscher on the 3rd of August 2015.

en: This folder contains all UAV flights paths that we created for the Sankt Annafirn, the Findelengletscher and Griesgletscher. They have been created with the software eMotion2, that was developped for the eBee platform from Sensefly.

en:
 UAV-derived DSMs and orthoimages

Unmanned Aerial Vehicle (UAV) surveys were conducted between 2015 and 2016 on the Sankt Annafirn, Findelen- and Griesgletscher, situated in the Swiss Alps. Three surveys at the Sankt Annafirn allowed for a full glacier coverage, four surveys at Griesgletscher allowed an almost full glacier coverage and seven surveys at Findelengletscher allowed for a partial coverage of the glacier tongue (see individual datasets for exact extent). For each survey, a high resolution orthoimage and a Digital Surface Model (DSM) was created.

 UAV surveys:

Prior flight, Ground Control Points (GCPs) were deployed on the glacier surface and measured with a differential GPS (Trimble R7 or Leica GPS 1200). They allowed precise georeferencing of the UAV-derived datasets. UAV flight plans were planned with the software *eMotion 2* and a SenseFly eBee was used as surveying platform. The images were then processed with the software Agisoft Photoscan Pro 1.1.6 .

The location and dates of each survey can be found in the table together with the number of flights performed (Nflights), the number of acquired images (Nimages), the number of GCPs set (NGCPs) and the surveyed area.

A folder for each dataset is available (see folder name in table), which contains:

- An orthoimage *glacier_date_photoscan_oi_CH1903+_LV95_0.1m.tif*

- A Digital Surface Model *glacier_date_photoscan_dsm_CH1903+_LV95_0.1m.tif*

- The Agisoft Photoscan automatic processing report  *glacier_date_photoscan_report.pdf*

where:

- *glacier* is the name of the surveyed glacier

- *date* is the date of the UAV image acquisition

- *photoscan* is the name of the photogrammetric software

- *oi* or *dsm* the type of dataset

- *CH1903+_LV95* is the coordinate system and datum of the dataset

- *0.1m* is the resolution of the dataset in meter

- *.tif* is the extention of the dataset

Details about the UAV surveys, the image processing and the accuracy of the UAV-derived products can be found in this publication below.

Paper Citation:
 > _Gindraux et al. 2017. Accuracy Assessment of Digital Surface Models from Unmanned Aerial Vehicles’Imagery on Glaciers, Remote Sensing, 9, 186, 1-15, [doi: 10.3390/rs9020186](https://doi.org/10.3390/rs9020186)._

The folder UAV_flight_paths.zip contains all UAV flights performed on the Sankt Annafirn, Findelengletscher and Griesgletscher. The flights were planned with the software eMotion2 and have the .afp extention.

alps

display_name: alps

dem

display_name: dem

drone

display_name: drone

dsm

display_name: dsm

findelengletscher

display_name: findelengletscher

glacier

display_name: glacier

gletscher

display_name: gletscher

griesgletscher

display_name: griesgletscher

orthoimage

display_name: orthoimage

orthophoto

display_name: orthophoto

sankt-annafirn

display_name: sankt-annafirn

uav

display_name: uav

en: UAV-derived Digital Surface Models and orthoimages for three alpine glaciers


en: snow-profile avalanche-activity soil-moisture avalanche glide-snow-avalanche

en: This file explains all provided datasets, variables and their units.

en: This file contains the release areas (polygon) of glide-snow avalanches as a shapefile.

media_type: text/csv

en: This file contains all soil measruements (liquid water content and matric potential) recorded at the reference location.

format: CSV

en: This file contains all sensor recordings in the Seewer Berg slope (time interval: 15 minutes).

en: This file contains the daily avalanche activity on Dorfberg as extracted from time-lapse photographs.

en: This file contains the coordinates of the reference location and the sensors in the Seewer Berg slope as a shapefile.

en: This file contains the aggregated data from manually recorded snow profiles in the reference location, 100m northwest of the Seewer Berg slope and in release areas of glide-snow avalanches in the Seewer Berg slope.

en: This file provides an overview of the dataset, the detailed measurement setup, and points out limitations.

en: This file contains SNOWPACK simulations (snow height, air temperature, rain) at a virtual station in the reference location. The virtual station was interpolated between the Weissfluhjoch (WFJ2) and Klosters Madrisa (KLO2) IMIS Stations.

en:
This dataset consists of spatio-temporal soil measurements and local snow measurements which were recorded to investigate glide-snow avalanche release in the Seewer Berg slope (Davos, Switzerland) from Nov 2021 to June 2024. Investigations based on this dataset were published in the research article:
Fees A., Lombardo M., van Herwijnen A., Lehmann P., Schweizer J. (2025). The source, quantity, and spatial distribution of interfacial water during glide-snow avalanche release: experimental evidence from field monitoring. The Cryosphere
The dataset consists of:
- Soil measurements (temperature and liquid water content) at soil depths of -5cm, -10cm, and -20cm
- Matric potential at depths of -5cm, -10cm, and -20cm
- Manual snow profiles (Snow height, temperature, liquid water content, bulk density)
- Metadata and manual snow profiles on glide-snow avalanches that released in the Seewer Berg slope
- Snow height, air temperature and rain simulated with SNOWPACK.

avalanche

display_name: avalanche

avalanche-activity

display_name: avalanche-activity

glide-snow-avalanche

display_name: glide-snow-avalanche

snow-profile

display_name: snow-profile

soil-moisture

display_name: soil-moisture

educ

en: Education, culture and sport

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: Spatio-temporal soil and local snow monitoring in a glide-snow avalanche prone slope above Davos Switzerland


maintainer: Elisabeth Hafner

en: reliability avalanche-size-estimation remote-sensing avalanche-mapping avalanche

en: AvalancheReliabilityData

en: The .zip contains all data used to conduct the reliability study as well as the results, a detailed description of the included files is contained in the included pdf. All geospatial data is provided in the Swiss Coordinate System: CH1903+ / LV95 (EPSG 2056). For any use of the data the proper citation provided is obligatory!

mimetype: application/x-zip-compressed

en:
This dataset contains the data used and collected to investigate the reliability of avalanche size estimates and avalanche outlines (see related publications). Namely this is

 Avalanche size estimates

* the 10 pictures depicting avalanches
* the survey results from the 170 participants

 Avalanche outlines mapped from oblique photographs
* the pictures of the six avalanches
* the avalanche outlines mapped by the 10 participants
* the reference mapped from the georeferenced photographs

 Avalanche outlines from remotely-sensed imagery
* the orthophotos in the four different resolutions (2m, 1m, 50cm, 25cm)
* the area of interest (AoI) delimiting the research area
* the avalanche mappings in each resolution for all five participants
* the shade masks used to separate illuminated and shaded areas

The acquisition of the orthophotos has been partially supported by the Swiss National Science Foundation (SNF; Grant N°200021_172800).

avalanche-mapping

display_name: avalanche-mapping

avalanche-size-estimation

display_name: avalanche-size-estimation

reliability

display_name: reliability

remote-sensing

display_name: remote-sensing

en: Data reliability study: avalanche size estimates and outlines


maintainer: Anita Risch

en: grazing ecosystem-coupling subalpine ecosystem-multifunctionality grassland vertebrates swiss-national-park exclusion ecosystem-functions invertebrates

en: Datafile

en:
ID: Plot ID composited of Fence & Treatment number (90 plots total)

Grassland: Name of the six subalpine grasslands where the exclosure setups were erected. In large grasslands (GRIM, MING, STAB), we established four hierarchical exclosure setups (two in short- and two in tall-grass vegetation), whereas in the small grasslands (BOTS, DADA, MARG) only one setup was erected per vegetation type. BOTS = Val dal Botsch, GRIM = Grimmels, MING = Val Mingér, STAB = Alp Stabelchod, DADA = Stabelchod da daint, MARG = Margunet

Fence: Number of exclosure setup (1 - 18). Note that uneven numbers (1,3,5,7,9,11,13,15,17) represent setups established on short-grass vegetation, even numbers (2,4,6,8,10,12,14,16,18) setups established in tall-grass vegetation
Vegetation	Vegetation type, 1 = short-grass vegetation, 2 = tall-grass vegetation; (9 replicate fences on each vegetation type)
Treatment	Progressive animal exclusion, numbers indicate which animals had access to the plot: 1 = Large/medium/small mammals, and invertebrates have access ("L/M/S/I"), 2 = Medium/small mammals, and invertebrates have access (“M/S/I”), 3 = Small mammals and invertebrates have access (“S/I”), 4 = Invertebrates have access (“I”), 5 = No animals have access (“None”)

Bulkden:	Fine fraction soil bulk density (g cm-3)

Soil.moist	: Soil moisture (%)

Soil.org.C: Rhizosphere soil C content (%)

pH: Soil pH

Nema.PC1: First principal component (PC1) of principal component analysis (PCA) of the soil nematode community composition

Nema.PC2: Second principal component (PC2) of principal component analysis (PCA) of the soil nematode community composition

Micro.PC1: 	First principal component (PC1) of principal component analysis (PCA) of the soil microbial community composition

Micro.PC2: Second principal component (PC2) of principal component analysis (PCA) of the soil microbial community composition

Abv.Inv.PC1: First principal component (PC1) of principal component analysis (PCA) of the aboveground-dwelling invertebrate community composition

Abv.Inv.PC2: Second principal component (PC2) of principal component analysis (PCA) of the aboveground-dwelling invertebrate community composition

Arthr.PC1: First principal component (PC1) of principal component analysis (PCA) of the soil arthropod community composition

Arthr.PC2: Second principal component (PC2) of principal component analysis (PCA) of the soil arthropod community composition

Plant.PC1: First principal component (PC1) of principal component analysis (PCA) of the plant community composition

Plant.PC2: Second principal component (PC2) of principal component analysis (PCA) of the plant community composition

Root.biomass: Root biomass (g m-2)

Micro.biomass	: Microbial biomass carbon (mg kg-1)

Plant.richness: Plant species richness

Plant.N: Plant tissue nitrogen content (%)

Soil.N.min: Soil net nitrogen mineralisation (kg ha-1 season)

Soil.resp: Soil carbon dioxide emissions (soil respiration; g m-2 h-1)

format: XLS

en:
This dataset contains all data on which the following publication below is based.

Paper Citation:
 > Risch AC, Ochoa-Hueso R, van der Putten WH, Bump JK, Busse MD, Frey B, Gwiazdowicz DJ, Page-Dumroese DS, Vandegehuchte ML, Zimmermann S, Schütz M. Size-dependent loss of aboveground animals differentially affects grassland ecosystem coupling and functions. 2018. Nature Communications 9: 3684. [doi: 10.1038/s41467-018-06105-4](https://doi.org/10.1038/s41467-018-06105-4).

Please cite this paper together with the citation for the datafile.

#Methods
Study sites
The experimental exclosure setups were installed within the SNP (IUCN category Ia preserve; Dudley 2008), in south-eastern Switzerland. The park covers 172 km2 of forests and subalpine and alpine grasslands along with scattered rock outcrops and scree slopes. The entire area has been protected from human impact (no hunting, fishing, camping or off-trail hiking) since 1914. Large, fairly homogenous patches of short- and tall-grass vegetation, which originate from different historical management and grazing regimes, cover the park’s subalpine grasslands entirely. Short-grass vegetation developed in areas where cattle used to rest (nutrient input) prior to the park’s foundation (14th century to 1914) (Schütz and others 2003, 2006) and is dominated by lawn grass species such as Festuca rubra L., Briza media L. and Agrostis capillaris L. (Schütz and others 2003, 2006). Today, this vegetation type is intensively grazed by diverse vertebrate and invertebrate communities that inhabit the park and consume up to 60% of the available biomass (Risch and others 2013). Tall-grass vegetation developed where cattle formerly grazed, but did not rest, and is dominated by rather nutrient-poor tussocks of Carex sempervirens Vill. and Nardus stricta L. (Schütz and others 2003, 2006). This vegetation type receives considerably less grazing, with only roughly 20% of the biomass consumed (Risch and others 2013). Consequently, the two vegetation types together represent a long-term trajectory of changes in grazing regimes. Underlying bedrock of all grasslands is dolomite, which renders these grasslands rather poor in nutrients regardless of former and current land-use regimes.
Experimental design
To progressively exclude aboveground vertebrate and invertebrate animals, we established 18 size-selective exclosure setups (nine in short-grass, nine in tall-grass vegetation) distributed over six subalpine grasslands across the SNP (Risch and others 2013, 2015). Elevation differences of exclosure locations did not exceed 350 m (between 1975 and 2300 m a.s.l.). The exclosures were established immediately after snowmelt in spring 2009 and were left in place for five consecutive growing seasons (until end of 2013). They were, however, temporarily dismantled every fall (late October after first snowfall) to protect them from avalanches. They were re-established in the same location every spring immediately after snowmelt. Each size-selective exclosure setup consisted of five plots (2 x 3 m) that progressively excluded aboveground vertebrates and invertebrates from large to small. The plots are labelled according to the guilds that had access to them “L/M/S/I”, “M/S/I”, “S/I”, “I”, “None”; L = large mammals, M = medium mammals, S = small mammals, I = invertebrates, None = no animals had access. As we only had permission to have the experimental setup in place for five consecutive growing seasons, the experiment had to be completely dismantled in the late fall of 2013 and all material removed from the SNP.
Our exclosure design was aimed at excluding mammalian herbivores, but naturally also excluded the few medium and small mammalian predators, as well as the entire aboveground invertebrate food web. A total of 26 large to small mammal species can be found in the SNP, but large apex predators are missing (wolf, bear, lynx) . Reptiles, amphibians and birds are scarce to absent in the subalpine grasslands under study. Only two reptile species occur in the park and they are confined to rocky areas that warm up enough for them to survive. One frog species spawns in an isolated pond far from our grasslands. Only three bird species occasionally feed on the subalpine grasslands. Using game cameras (Moultrie 6MP Game Spy I-60 Infrared Digital Game Camera, Moultrie Feeders, Alabaster, AL, USA), we did observe that the medium- and small-sized mammals (marmot/hares and mice) were not afraid to enter the fences and feed on their designated plots. We never spotted reptiles, amphibians or birds on camera. We distinguished between 59 higher aboveground-dwelling invertebrate taxa that our size-selective exclosures excluded (see also methods for aboveground-dwelling invertebrates below).
The “L/M/S/I” plot (not fenced) was located at least 5 m from the 2.1 m tall and 7 x 9 m large main electrical fence that enclosed the other four plots. The bottom wire of this fence was mounted at 0.5 m height and was not electrified to enable safe access for medium and small mammals, while fencing out the large ones. Within each main fence, we randomly established four 2 x 3 m plots separated by 1-m wide walkways from one another and from the main fence line: 1) the “M/S/I” plots were unfenced, allowing access to all but the large mammals; 2) the “S/I” plots (10 x 10 cm electrical mesh fence) excluded all medium-sized mammals. Note that the bottom 10 cm of this fence remained non-electrified to enable safe access for small mammals; 3) the “I” plots (2 x 2 cm metal mesh fence) excluded all mammals. We double-folded the mesh at the bottom 50 cm to reduce the mesh size to smaller than 1 x 1 cm openings; and 4) the “None” plots were surrounded by a 1 m tall mosquito net (1.5 x 2 mm) to exclude all animals. The top of the plot was covered with a mosquito-meshed wooden frame mounted to the corner posts (roof). We treated these plots a few times with biocompatible insecticide (Clean kill original, Eco Belle GmbH, Waldshut-Tiengen, Germany) to remove insects that might have entered during data collection or that hatched from the soil, but amounts were negligible and did not impact soil moisture conditions within these plots.
To assess whether the design of the “None” exclosure (mesh and roof) affected the response variables within the plots and, therefore, influenced the results, we established an additional six “micro-climate control” exclosures (one in each of the six grasslands) (Risch and others 2013, 2015). These exclosures were built as the “None” exclosures but were open at the bottom (20 cm) of the 3-m side of the fence facing away from the prevailing wind direction to allow invertebrates to enter. A 20-cm high and 3-m long strip of metal mesh was used to block access to small mammals. Thus, this construction allowed a comparable micro-climate to the “None” plots, but also a comparable feeding pressure by invertebrates to the “I” plots. We compared various properties within these exclosures against one another to assess if our construction altered the conditions in the “None” plots. We showed that differences in plant (e.g., vegetation height, aboveground biomass) and soil properties (e.g., soil temperature, moisture) found between the “I” and the “None” treatments were not due to the construction of the “None” exclosure, but a function of animal exclusions, although the amount of UV light reaching the plant canopy was significantly reduced (Risch and others 2013).
Aboveground invertebrate sampling
Aboveground invertebrates were sampled with two different methods to capture both ground- and plant-dwelling organisms: 1) we randomly placed two pitfall traps (67 mm in diameter, covered with a roof) filled with 20% propylene glycol in one 1 x 1 m subplot of the 2 x 3 m treatment plots in spring 2013 (May) and emptied them every two weeks until late September 2013 (Vandegehuchte and others 2017b, 2018). A pitfall trap consisted of a plastic cylinder (13 cm depth, 6.75 cm diameter). Within each cylinder we placed a 100 ml plastic vial with outer diameter 6.70 cm and on top of the cylinder we placed a plastic funnel to guide the invertebrates into the vials. Each trap was cover with a cone-shaped and transparent plastic roof to protect the trap from rain (Vandegehuchte and others 2017b, 2018). Note that in the “None” plots only one trap was placed as control to check for effectiveness of the exclosure. 2) We vacuumed all invertebrates from a 60 x 60 cm area on another 1 x 1 m subplot with a suction sampler (Vortis, Burkhard manufacturing CO, Ltd., Rickmansworth, Hertfordshire, UK) every month from June to September 2013 (Vandegehuchte and others 2017b, 2018). For this purpose, we quickly placed a square plastic frame (60 x 60 x 40 cm) with a closable mosquito mesh sleeve attached to the top edge into the plot from the outside. The suction sample was then inserted into through the sleeve and operated for 45 s to collect the invertebrates (Vandegehuchte and others 2017b, 2018).
We sorted the ≈100 000 individuals collected with both methods by hand and identified each individual morphologically to the lowest taxonomic level feasible (59 taxa, including orders, suborders, subfamilies, families; phylum for Mollusca). These taxa belonged to the following feeding types: 19 herbivores, 16 detritivores, 9 predators, 8 mixed feeders, 5 omnivores and 2 non-classified feeders (or not feeding as adults) (Vandegehuchte and others 2017b). We summed the numbers from the two pitfall traps and the suction sampling over the course of the 2013 season to represent the aboveground invertebrate abundance and community composition of a plot. Note: we did not specifically attempt to catch flying invertebrates with e.g., sticky traps, thus a few flying insects may have been missed with our vacuum sampling approach.
Sampling of plant properties
The vascular plant species composition was assessed at peak biomass every summer (July) by estimating the frequency of occurrence of each species with the pin count method in each plot (Frank and McNaughton 1990). A total of 172 taxa occurred within our 90 plots and we calculated plant species richness for each plot separately. We used the 2013 data in this study. Plant quality was assessed every year in July and September; here we use plant quality at the end of the experiment (September 2013). Two 10 x 100 cm wide strips of vegetation per plot were clipped, combined, dried at 65°C, and ground (Pulverisette 16, Fritsch, Idar-Oberstein, Germany) to pass through a 0.5 mm sieve. Twenty randomly selected samples across all treatments were analysed for N (Leco TruSpec Analyser, Leco, St. Joseph, Michigan, USA) (Vandegehuchte and others 2015). Nitrogen concentrations of the other samples were then estimated from models established for the experiment and the entire SNP relating Fourier transform-near infrared reflectance (FT-NIR) spectra to the measured values of N using a multi-purpose FT-NIR spectrometer (Bruker Optics, Fällanden, Switzerland) (Vandegehuchte and others 2015). Root biomass was sampled every fall by collecting five 2.2 cm diameter x 10 cm deep soil samples (Giddings Machine Company, Windsor, CO, USA) per plot (450 samples year-1). The samples were dried at 30 °C and roots were sorted from the sample by hand. We sorted each sample for 1 h which allowed to retrieve over 90% of all roots present in the samples (Risch and others 2013). The roots were then dried at 65 °C for 48 and weighed to the nearest mg. We averaged the values per plot and used the 2013 data only in this study.
Sampling of edaphic communities
In 2009, 2010, and 2011 we collected three composited soil samples (5 cm diameter x 10 cm depth; AMS Samplers, American Falls, ID, USA) and assessed bacterial community structure using T-RFLP profiling (Liu and others 1997; Blackwood and others 2003; Hodel and others 2014). We detected a total of 89 operational taxonomic units (OTUs). These values are in accordance with other studies reporting OTU richness (Wirthner and others 2011; Zumsteg and others 2012; Meola and others 2014) using T-RFLP profiling, a method that detects the most abundant, and thus likely, the most relevant, taxa. We averaged the data over the three years of collections for our calculations. Microbial biomass carbon (MBC) was determined with the substrate-induced method (Anderson and Domsch 1978) every fall (September) between 2009 and 2013 by collecting three mineral soil samples (5 cm diameter × 10 cm mineral soil core, AMS Samplers, American Falls, ID, USA). The three samples were combined (90 samples for each sampling year), immediately put on ice, taken to the laboratory, passed through a 2-mm sieve and stored at 4°C. Again, we only used the 2013 data in this study.
Soil samples (5 cm diameter x 10 cm depth) to extract soil arthropods were collected in June, July, and August 2011 with a soil corer lined with a plastic sleeve to ensure an undisturbed sample (total of 270 samples). The plastic line core was immediately sealed on both ends using cling film and put into a cooler. All plots were sampled within three days and the extraction of arthropods started the evening of the sampling day using a high-gradient Tullgren funnel apparatus (Crossley and Blair 1991; Vandegehuchte and others 2015). Samples were kept in the extractor for four days and the soil arthropods were collected in 95% ethanol. All individuals were counted and each individual was identified morphologically to the lowest level feasible [76 taxa, including orders, suborders, subfamilies, families (Protura, Thysanoptera, Aphidina, Psylina, Coleoptera, Brachycera, Nematocera, Auchenorryncha, Heteroptera, Formicidae); sub-phylum for Myriapoda, for Acari and Collembola also including morpho-species). Note that we also included larval stages (nine of the 76 taxa) (Vandegehuchte and others 2015). All data were summed over the season. A detailed species list for mites and collembolans is published (Vandegehuchte and others 2017a) [https://doi.org/10.1371/journal.pone.0118679.s001]. Earthworms are rare in the SNP and therefore were not included. We collected eight random 2.2 cm diameter x 10 cm deep soil cores from each plot in September 2013 to determine the soil nematode community composition. The samples were mixed and the nematodes were extracted from 100 ml of fresh soil using Oostenbrink elutriators (Oostenbrink 1960). All nematodes in a 1 ml of the 10 ml extract were counted, a minimum of 150 individuals sample-1 were identified to genus or family level using (Bongers 1988), the numbers of all nematodes were extrapolated to the entire sample and expressed for a 100 g dry sample. In total we identified 63 genus or family levels (Vandegehuchte and others 2015). The list of all the nematodes found is published (Vandegehuchte and others 2015) [http://www.oikosjournal.org/appendix/oik-03341] or DOI: [doi: 10.1111/oik.03341].
We are aware that sampling soil microbes from 2009 to 2011 and soil arthropods in 2011 was not ideal, but we are positive that this does not bias the results. Most of the parameters measured in our experiment either already showed a treatment response after the first growing season (e.g., plant biomass) or did not respond over the entire time experiment (e.g., microbial biomass C). The microbial community composition (2009 – 2011) was highly influenced by inter-annual differences in temperature and precipitation, but did not differ between treatments or vegetation types (Hodel and others 2014). We therefore felt comfortable using the 2009 through 2011 data for describing the soil microbial community in our experimental treatments. Similarly, we are positive that our soil arthropod data are representative. We did assess soil arthropods in August 2012 and found no differences to the August 2011 data. However, we did not feel comfortable combining the 2011 June, July, August data with only August data for 2012 for our analyses.
Sampling of soil properties
We collected three soil samples (5 cm diameter x 10 cm depth) in each plot in September 2013 after removing the vegetation. First, we collected the top layer of mineral soil rich in organic matter, the surface organic layer or rhizosphere, typically 1 to 3 cm in depth with a soil corer (AMS Samples, American Falls, Idaho, USA). Second, we collected a 10 cm mineral soil core beneath this surface layer. The cores for each layer were composited, dried at 65 °C for 48 h and fine-ground to pass a 0.5 mm screen. We then analysed all samples for total C using a Leco TruSpec Analyser (Leco, St. Joseph, Michigan, USA). Mineral soil pH was measured potentiometrically in 1:2 soil:CaCl2 solution with an equilibration time of 30 min.
Soil net N mineralisation was assessed during the 2013 growing season (Risch and others 2015). For this purpose, we randomly collected a 5 cm diameter x10 cm deep soil sample with a soil corer (AMS Samples, American Falls, Idaho, USA) after clipping the vegetation in June 2013. After weighing and sieving (4 mm mesh) the soil, we extracted a 20 g subsample in 1 mol l-1 KCl for 1.5 h on an end-over-end shaker and thereafter filtered it through ashless folded filter paper (DF 5895 150, ALBET LabScience, Hahnenmühle FineArt GmbH, Dassel, Germany). From these filtrates NO3- concentrations were measured colorimetrically (Norman and Stucki 1981) and NH4+with flow injection analysis (FIAS 300, Perkin Elmer, Waltham Massachusetts, USA) (Risch and others 2015). We dried the rest of the sample 105 °C to constant mass to determine fine,fraction bulk density. A second soil sample was collected within each plot in June 2013 with a corer lined with a 5 x 13 cm aluminium cylinder. The corer was driven 11.5 cm deep into the soil so that the top 1.5 cm of the cylinder remained empty. Into this space we placed a polyester bag (250 µm) filled an ion-exchanger resin to capture the incoming N. The bag was filled with a 1:1 mixture of acidic and alkaline exchanger resin (ion-exchanger I KA/ion exchanger IIIAA, Merck AG, Darmstadt, Germany). We then removed 1.5 cm soil at the bottom of the cylinder and placed a second resin exchanger bag into this space to capture the N leached from the soil column. To assure that the exchange resin was saturated with H+ and Cl- prior to filling the bags, the mixture was stirred with 1.2 ml l-1 HCl for 1 h and then rinsed with demineralized water until the electrical conductivity of the water reached 5 µm cm-1. The cylinder with the resin bags in place was reinserted into the soil with the top flush to the soil surface and incubated for three months. We recollected the cylinders in September 2013. Each resin bag and 20 g of sieved soil (4 mm mesh) from each cylinder were then separately extracted with KCl and NO3- and NH4+ concentrations were measured. Nitrate and NH4+ concentrations of all samples were then converted to a content basis by multiplying their values with fine fraction bulk density. Net N mineralisation was thereafter calculated as the difference between the N content of the samples collected at the end of the three-month incubation (including the N extracted from the bottom resin bag) and the N content at the beginning of the incubation (Risch and others 2015).
Soil CO2 emissions were measured every two weeks between 0900 and 1700 hrs from early May through late September 2013 with a PP-Systems SRC-1 soil respiration chamber (15 cm high, 10 cm diameter; closed circuit) attached to a PP-Systems EGM-4 infrared gas analyser (PP-Systems, Amesbury, MA, USA) on two locations per plot (Risch and others 2013). The chamber was placed on randomly placed, permanently installed PVC collars (10 cm diameter) driven 5 cm into the soil at the beginning of the study (Risch and others 2013). Freshly germinated plants growing within the collars were removed prior to each measurement to avoid measuring plant respiration or photosynthesis. The two measurements collected per plot and sampling date were averaged.
Soil moisture (with time domain reflectometry; Field-Scout TDR-100, Spectrum Technologies, Plainfield, Illionois, USA) and temperature (with a waterproof digital pocket thermometer; Barnstead International, Dubuque, Iowa, USA) were measured at five random locations per plot every two weeks during the growing seasons during the experiment for the 0 to 10 cm depth (Risch and others 2013, 2015). As soil moisture and soil temperature were highly negatively correlated (Risch and others 2013), we only used soil moisture for this study. We used plot-level averages of all values available to capture soil moisture variability during the five years of the experiment. The results remained unchanged when we only used soil moisture from the 2013 growing season.
Numeral calculations and statistical analyses
Ecosystem coupling. We conducted principal component analyses (PCAs; unscaled) at the complete dataset level using the abundances of each taxonomical entity to describe each of the five different communities used in this study: aboveground-dwelling invertebrates, vascular plants, soil microorganisms, soil arthropods and soil nematodes. We retained the first two components (PCA axis 1 and PCA axis 2) of each analysis as we found them to adequately represent the temporal and spatial variability of our 90 treatment plots in previous studies55,67. Together they explained a total of 71.70% of the variation for aboveground invertebrates, 44.36% for plants, 44.85% for soil microorganisms, 61.85% for soil arthropods and 77.19% for soil nematodes. In addition, we used soil pH and soil organic C content as a proxy for soil chemical properties, soil bulk density as a proxy for soil physical properties and soil moisture (negatively correlated with soil temperature) as a proxy for soil micro-climatic conditions for an overall total of fourteen constituents.
We calculated ecosystem coupling9 for each exclosure treatment within each vegetation type (i.e., 2  5 treatment combinations in total) as an integrated measure of pairwise ecological interactions between ecosystem constituents representing ecological communities and the soil abiotic environment. These ecological interactions are defined by non-parametric Spearman rank correlation analyses between two constituents, excluding interactions involving two abiotic constituents (e.g., soil pH vs. soil moisture) and interactions between the first (PC1) and second (PC2) component of each community type, as these are orthogonal by definition. Interactions between abiotic constituents were excluded from the analyses because the focus of our study was on communities and how they interact with one another and their surrounding environment; therefore, including abiotic-abiotic interactions was not of interest here. Given that the effectiveness of our experimental design resulted in that no community composition data of aboveground-dwelling invertebrates was available for the “None” plots (all animals excluded), only thirteen instead of fourteen constituents were included in the ecosystem coupling calculations for this treatment. The complete absence of aboveground invertebrates represents the most extreme case of disturbance between aboveground animal communities and the rest of the ecosystem constituents. This may have resulted in a slight overestimation of ecosystem coupling for these plots.
	Average ecosystem coupling was calculated as follows:
Ecosystem coupling=
where Xi is the absolute Coupling was calculated value of the Spearman’s rho coefficient of the ith correlation for each treatment within each vegetation type (i.e., based on nine replicates each), considering and n is the number of pairwise comparisons considered (n = a total of 80; interactions (56 in the case of the “None” treatment). We considered a total of 40 biotic-biotic interactions (i.e., concerning two community-level principal components such as plants and microbes; 24 in the case of the “None” treatment) and 40 abiotic-biotic (i.e., concerning one community-level principal component and one abiotic factor, e.g., plant community and soil properties; 32 in the case of the “None” treatment).	Coupling was calculated for each treatment within each vegetation type (i.e., based on nine replicates each), considering a total of 80 interactions (56 in the case of the “None” treatment). We considered a total of 40 biotic-biotic interactions (i.e., concerning two community-level principal components such as plants and microbes; 24 in the case of the “None” treatment) and 40 abiotic-biotic (i.e., concerning one community-level principal component and one abiotic factor, e.g., plant community and soil properties; 32 in the case of the “None” treatment).
To establish whether constituents were significantly and positively coupled within treatments (i.e., the average of their correlation coefficients were greater than in a null model where correlation only happens by chance), we calculated one-tailed p-values based on permutation tests with 999 permutations.

We considered six ecosystem functions and process rates commonly used to assess ecosystem functioning (Meyer and others 2015; Manning and others 2018). Plant N content represents a measure of forage quality, while plant richness has been shown to stabilise biomass production, thus allowing the system to respond to changes in herbivory. Soil net N mineralisation, soil respiration, root biomass, and microbial biomass represent fluxes or stocks of energy. For all functions and processes higher values represent higher functioning (Manning and others 2018). All these variables were measured in the last year of the experiment (2013). We then quantified ecosystem multifunctionality using the multiple threshold approach (Byrnes and others 2014; Manning and others 2018), which considers the number of functions that are above a certain threshold, over a series of threshold values (typically 10-99%) that are defined based on the maximum value of each function. We weighted all our functions equally for these calculations (Manning and others 2018). The number of functions in a plot with values higher than a given threshold value for the respective function is summed up. The sum represents ecosystem multifunctionality for that plot. Given that choosing any particular threshold as a measure of ecosystem multifunctionality is arbitrary, we calculated the average of thresholds from 10-90% (in 10% intervals) as a more integrated representation of ecosystem multifunctionality.
We used Pearson correlations to explore the relationships between ecosystem coupling (all interactions, biotic-biotic interactions, abiotic-biotic interactions involving above- and belowground constituents, and all interactions, biotic-biotic interactions, abiotic-biotic interactions involving belowground constituents only) and ecosystem multifunctionality by calculating the slopes of all relationships between ecosystem coupling and multifunctionality for all thresholds between 10 and 99%. We also related ecosystem coupling with the average of multifunctionality at thresholds between 30-80% as explained before and considered this correlation as a robust indication of the type of association between these two variables. In addition, we explored the relationships between ecosystem coupling (all interactions, biotic-biotic interactions, abiotic-biotic interactions involving above- and belowground constituents, and all interactions, biotic-biotic interactions, abiotic-biotic interactions involving belowground constituents only) and individual ecosystem functions. The effects of exclosures and vegetation type on individual functions and multifunctionality were evaluated using linear mixed effects models ('lme' function of the nlme package), with exclosure and vegetation type as fixed effects and fence as a random factor. All statistical analyses and numerical calculations were done in R version 3.4.0 (R Core Team 2016).

#References

- Anderson J, Domsch K. 1978. A physiological method for the quantitative measurement of microbial biomass in soil. Soil Biol Biochem 10:215–21.
- Blackwood CB, Marsh T, Kim S-H, Paul EA. 2003. Terminal Restriction Fragment Length Polymorphism Data Analysis for Quantitative Comparison of Microbial Communities. Appl Environ Microbiol 69:926–32. http://www.ncbi.nlm.nih.gov/pmc/articles/PMC143601/
- Bongers T. 1988. De nematoden von Nederland. Schoorl, The Netherlands: Pirola
- Byrnes JEK, Gamfeldt L, Isbell F, Lefcheck JS, Griffin JN, Hector A, Cardinale BJ, Hooper DU, Dee LE, Duffy JE. 2014. Investigating the relationship between biodiversity and ecosystem multifunctionality: Challenges and solutions. Methods Ecol Evol 5:111–24.
- Crossley DAJ, Blair JM. 1991. A high-efficiency low-technology Tulgren-type extractor for soil microarthopods. Agric Ecosyst Environ 34:187–92.
- Dudley N. 2008. Guidelines for applying protected area managment categories. Gland: IUCN
- Frank DA, McNaughton SJ. 1990. Aboveground biomass estimation with the canopy intercept method: A plant growth form caveat. Oikos 57:57–60.
- Haynes AG, Schütz M, Buchmann N, Page-Dumroese DS, Busse MD, Risch AC. 2014. Linkages between grazing history and herbivore exclusion on decomposition rates in mineral soils of subalpine grasslands. Plant Soil 374.
- Hodel M, Schütz M, Vandegehuchte ML, Frey B, Albrecht M, Busse MD, Risch AC. 2014. Does the aboveground herbivore assemblage influence soil bacterial community composition and richness in subalpine grasslands? Microb Ecol 68:584–95.
- Liu WT, Marsh TL, Cheng H, Forney LJ. 1997. Characterization of microbial diversity by determining terminal restriction fragment length polymorphisms of genes encoding 16S rRNA. Appl Environ Microbiol 63:4516–22. http://www.ncbi.nlm.nih.gov/pmc/articles/PMC168770/
- Manning P, van der Plas F, Soliveres S, Allan E, Maestre FT, Mace G, Whittingham MJ, Fischer M. 2018. Redefining ecosystem multifunctionality. Nat Ecol Evol 2:427–36. https://doi.org/10.1038/s41559-017-0461-7
- Meola M, Lazzaro A, Zeyer J. 2014. Diversity, resistance and resilience of the bacterial communities at two alpine glacier forefields after a reciprocal soil transplantation. Environ Microbiol 16:1918–34. https://onlinelibrary.wiley.com/doi/abs/10.1111/1462-2920.12435
- Meyer ST, Koch C, Weisser WW. 2015. Towards a standardized Rapid Ecosystem Function Assessment (REFA). Trends Ecol Evol 30:390–7. http://www.sciencedirect.com/science/article/pii/S0169534715000968
- Norman R., Stucki JW. 1981. The determination of nitrate and nitrite in soil extracts by ultraviolet spectrophotometry. Soil Sci Soc Am J 45:347–53.
- Ochoa-Hueso R. 2016. Non-linear disruption of ecological interactions in response to nitrogen deposition. Ecology 87:2802–2814.
- Oostenbrink M. 1960. Estimating nematode populations by some selected methods. In: Sasser NJ, Jenkins WR, editors. Nematology. Chapel Hill, NC, USA: University of North Carolina Press. pp 85–101.
- R Core Team. 2016. R: A language and environment for statistical computing. Vienna, Austria: R Foundation for Statistical Computing
- Risch AC, Haynes AG, Busse MD, Filli F, Schütz M. 2013. The response of soil CO2 fluxes to progressively excluding vertebrate and invertebrate herbivores depends on ecosystem type. Ecosystems 16:1192–202.
- Risch AC, Schütz M, Vandegehuchte ML, Van Der Putten WH, Duyts H, Raschein U, Gwiazdowicz DJ, Busse MD, Page-Dumroese DS, Zimmermann S. 2015. Aboveground vertebrate and invertebrate herbivore impact on net N mineralization in subalpine grasslands. Ecology 96:3312–22.
- Schütz M, Risch AC, Achermann G, Thiel-Egenter C, Page-Dumroese DS, Jurgensen MF, Edwards PJ. 2006. Phosphorus translocation by red deer on a subalpine grassland in the Central European Alps. Ecosystems 9:624–633.
- Schütz M, Risch AC, Leuzinger E, Krüsi BO, Achermann G. 2003. Impact of herbivory by red deer (Cervus elaphus L.) on patterns and processes in subalpine grasslands in the Swiss National Park. For Ecol Manage 181:177–88.
- Vandegehuchte ML, van der Putten WH, Duyts H, Schütz M, Risch AC. 2017a. Aboveground mammal and invertebrate exclusions cause consistent changes in soil food webs of two subalpine grassland types, but mechanisms are system-speciﬁc. Oikos 126:212–23.
- Vandegehuchte ML, Raschein U, Schütz M, Gwiazdowicz DJ, Risch AC. 2015. Indirect short- and long-term effects of aboveground invertebrate and vertebrate herbivores on soil microarthropod communities. PLoS One 10:e0118679.
- Vandegehuchte ML, Schütz M, de Schaetzen F, Risch AC. 2017b. Mammal-induced trophic cascades in invertebrate food webs are modulated by grazing intensity in subalpine grassland. J Anim Ecol 86:1434–46.
- Vandegehuchte ML, Trivellone V, Schütz M, Firn J, de Schaetzen F, Risch AC. 2018. Mammalian herbivores affect leafhoppers associated with specific plant functional types at different timescales. Funct Ecol 32:545–55.
- Wirthner S, Frey B, Busse MD, Schütz M, Risch AC. 2011. Effects of wild boar (Sus scrofa L.) rooting on the bacterial community structure in mixed-hardwood forest soils in Switzerland. Eur J Soil Biol 47:296–302. http://dx.doi.org/10.1016/j.ejsobi.2011.07.003
- Zumsteg A, Luster J, Göransson H, Smittenberg RH, Brunner I, Bernasconi SM, Zeyer J, Frey B. 2012. Bacterial, Archaeal and Fungal Succession in the Forefield of a Receding Glacier. Microb Ecol 63:552–64. https://doi.org/10.1007/s00248-011-9991-8

ecosystem-coupling

display_name: ecosystem-coupling

ecosystem-functions

display_name: ecosystem-functions

ecosystem-multifunctionality

display_name: ecosystem-multifunctionality

exclusion

display_name: exclusion

grassland

display_name: grassland

grazing

display_name: grazing

invertebrates

display_name: invertebrates

subalpine

display_name: subalpine

swiss-national-park

display_name: swiss-national-park

vertebrates

display_name: vertebrates

en: Ecosystem coupling and multifunctionality - exclosure experiment


disdrometer-data-laret

maintainer: Daniel Wolfensberger

title_for_slug: disdrometer-data-laret

en: precipitation hydrometeors raclets disdrometer visibility

en: Disdrometer Data Laret

en: The zip folder contains one netCDF file per day for Laret from February 7 to March 29 2019 with a temporal resolution of 30 seconds (time in UTC). The naming convention for the files is Laret_YYYYMMDD.nc and the files include the following: characteristics of hydrometeors (e.g. diameter, fall velocity, amount per diameter class,...), precipitation rate, radar reflectivity, visibility range, weather codes and instrument performance.

en:
A laser optical disdrometer (Parsivel² , OTT Hydromet) was used to measure hydrometeors by extinction when passing a laser beam. The instrument can classify eight different kinds of precipitation, including rain, hail, snow, drizzle, and hybrid forms.
The dataset contains information on precipitation amount and type for the period of February 7 to March 29 2019 in Laret.

disdrometer

display_name: disdrometer

hydrometeors

display_name: hydrometeors

precipitation

display_name: precipitation

raclets

display_name: raclets

visibility

display_name: visibility


maintainer: Yaquan Chang

en: plant-biodiversity tectonic-faults endemism climate-history relief

en:
This dataset includes geomorphic predictors and plant biodiversity patterns in the Hengduan Mountains, published in the Geological Society of London special volume: Asian Geodynamics, Climate and Biodiversity (https://doi.org/10.1144/SP549-2024-17).
The geomorphic predictors include catchment-restricted relief and chi maps, while the climate predictors comprise site water balance, growing degree days, and climate change velocity from the Last Glacial Maximum (LGM) to the present.
The plant biodiversity patterns are represented by a plant richness map for 13,321 species in the Hengduan Mountains. Species-level plant range maps are available in the dataset, previously published under DOI: 10.16904/envidat.424.

climate-history

display_name: climate-history

endemism

display_name: endemism

plant-biodiversity

display_name: plant-biodiversity

relief

display_name: relief

tectonic-faults

display_name: tectonic-faults

educ

en: Education, culture and sport

envidat

en: EnviDat: the Environmental Data Portal

en: Tectonic and climatic controls on plant biodiversity in the Hengduan Mountains China


en: snow snow-depth uas remote-sensing swe

en: HS map Brämabül, 14. April 2015

media_type: image/tiff

en:
10 cm resolution
15 cm accuracy

format: TIFF

mimetype: image/tiff

en: .tfw file

en: coordinates for the .tif raster

en:
This snow depth map was generated 14 January 2015, close to peak of winter accumulation, applying Unmanned Aerial System digital surface models with a spatial resolution of 10 cm. The covered area is 285'000 m2 at the top of Brämabüel, 2490 m a.s.l. covering all expositions. Coordinate system: CH1903LV03.

A detailed description is given here:

Bühler, Y., Adams, M. S., Bösch, R., and Stoffel, A.: Mapping snow depth in alpine terrain with unmanned aerial systems (UASs): potential and limitations, The Cryosphere, 10, 1075-1088, 10.5194/tc-10-1075-2016, 2016.

Abstract:
Detailed information on the spatial and temporal distribution, and variability of snow depth (HS) is a crucial input for numerous applications in hydrology, climatology, ecology and avalanche research. Nowadays, snow depth distribution is usually estimated by combining point measurements from weather stations or observers in the field with spatial interpolation algorithms. However, even a dense measurement network is not able to capture the large spatial variability of snow depth in alpine terrain.
Remote sensing methods, such as laser scanning or digital photogrammetry, have recently been successfully applied to map snow depth variability at local and regional scales. However, such data acquisition is costly, if manned airplanes are involved. The effectiveness of ground-based measurements on the other hand, is often hindered by occlusions, due to the complex terrain or acute viewing angles. In this paper, we investigate the application of unmanned aerial systems (UAS), in combination with structure-from-motion photogrammetry, to map snow depth distribution. Such systems have the advantage that they are comparatively cost-effective and can be applied very flexibly to cover also otherwise inaccessible terrain. In this study we map snow depth at two different locations: a) a sheltered location at the bottom of the Flüela valley (1900 m a.s.l.) and b) an exposed location (2500 m a.s.l.) on a peak in the ski resort Jakobshorn, both in the vicinity of Davos, Switzerland. At the first test site, we monitor the ablation on three different dates. We validate the photogrammetric snow depth maps using simultaneously acquired manual snow depth measurements. The resulting snow depth values have a root mean square error (RMSE) better than 0.07 to 0.15 m on meadows and rocks and a RMSE better than 0.30 m on sections covered by bushes or tall grass. This new measurement technology opens the door for efficient, flexible, repeatable and cost effective snow depth monitoring for various applications, investigating the worlds cryosphere.

remote-sensing

display_name: remote-sensing

snow

display_name: snow

snow-depth

display_name: snow-depth

swe

display_name: swe

uas

display_name: uas

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: UAS based snow depth maps Brämabüel, Davos, CH


tree-species-map-of-switzerland

maintainer: Tiziana Li Koch

title_for_slug: tree-species-map-of-switzerland

en: switzerland tree-species map remote-sensing forest

media_type: image/png

en: Image of the tree species map

format: PNG

en:
Dominant tree species map of Switzerland
We created a tree species map of Switzerland for the dominant tree species in the forested areas. The spatial resolution of the map is 10 m and the coordinate system is ETRS89-extended / LAEA Europe (EPSG 3035). The map comprises Sentinel-2 index time series from the year 2020, a digital elevation model and species reference data from the Swiss National Forest Inventory. The map is available as raster (.tif) or vector dataset (.gpkg).
**Access will be granted upon request.**
In total, the following 15 species were mapped:
*Abies alba*, *Acer pseudoplatanus*, *Alnus glutinosa*, *Alnus incana*, *Betula pendula*, *Castanea sativa*, *Fagus sylvatica*, *Fraxinus excelsior*, *Picea abies*, *Pinus cembra*, *Pinus mugo arborea*, *Pinus sylvestris*, *Quercus petraea*, *Quercus robur*, *Sorbus aucuparia*.

 Approach

 Data
- Swiss National Forest Inventory Data (stand species with > 60 % dominance in upper canopy; on at least more than 9 plots dominant)
- Sentinel-2 time series (2020, Indices: CCI, CIRE, NDMI, EVI, NDVI)
- Digital elevation model (DEM) (swissalti3d, 5 m)
- Biogeographical regions (Federal Office for the Environment FOEN)
- Forest mask 2017 (Approach: Waser et al., 2015)

 Modeling approach
We identified the most meaningful variables that led to separation of the respective groups by using random forest models with a forward feature selection (Meyer et al., 2018; Ververidis & Kotropoulos, 2005). In this approach, the final random forest model is solely built from the selected meaningful variables. By identifying meaningful variables, we can determine which variables might influence the grouping. Further, to avoid overfitting and overly optimistic results, we applied 10-fold spatial cross-validation and put all pixels from a plot in the same spatial fold.
The modeling was realized using the CAST package in R (Meyer et al., 2022), based on the well-known caret package (Kuhn, 2022). We used the ranger package in R (Wright & Ziegler, 2017) to implement the random forest models, due to its short computation time.

 Training data for modeling
- 295 Sentinel-2, DEM & Biogeographical variables
- 10525 tree species pixels

 Selected variables for final model
1. EVI of 2020.05.16
2. NDMI of 2020.03.12
3. CIRE of 2020.04.16
4. NDMI of 2020.07.05
5. CCI of 2020.05.11
6. dem
7. CCI of 2020.08.14
8. NDMI of 2020.08.24
9. CCI of 2020.12.22
10. NDMI of 2020.04.21
11. NDMI of 2020.11.17
12. NDMI of 2020.08.09
13. CIRE of 2020.03.22
14. CIRE of 2020.08.09
14. CCI of 2020.11.02
15. CIRE of 2020.06.10

 Overall Accuracy of final model
- 0.759

 Nationwide prediction
- Predicted throughout forest mask 2017 (Approach: Waser et al., 2015)
- Not applied on incomplete Sentinel-2 time series (own category in final map: incomplete_ts)
- Applied the Area of Applicability (Meyer 2022) to sort out pixels outside of the feature space; basically where the model had not the same values for pixels as in the available training data

 *Be aware that the map is only validated with the training data itself, an independent validation with other data sources remains missing*

 References
- Kuhn, M. (2022). Classification and Regression Training. 6.0-93.
- Meyer, H., Reudenbach, C., Hengl, T., Katurji, M., & Nauss, T. (2018). *Improving performance of spatio-temporal machine learning models using forward feature selection and target-oriented validation*. Environmental Modelling and Software, 101, 1-9. https://doi.org/10.1016/j.envsoft.2017.12.001
- Meyer, H., Milà, C., & Ludwig, M. (2022). *CAST: 'caret' Applications for Spatial-Temporal Models*. 0.7.0.
- Ververidis, D., & Kotropoulos, C. (2005). *Sequential forward feature selection with low computational cost*. 2005 13th European Signal Processing Conference.
- Waser, L., Fischer, C.,Wang, Z., & Ginzler, C. (2015). *Wall-to-Wall Forest Mapping Based on Digital Surface Models from Image-Based Point Clouds and a NFI Forest Definition*. Forests, 6, 12, 4510–4528.
- Wright, M. N., & Ziegler, A. (2017). *ranger: A Fast Implementation of Random Forests for High Dimensional Data in C++ and R*. Journal of Statistical Software, 77(1), 1-17. https://doi.org/doi:10.18637/jss.v077.i01

forest

display_name: forest

map

display_name: map

switzerland

display_name: switzerland

tree-species

display_name: tree-species

en: Tree species map of Switzerland


en: satellite snow avalanche hazard-mapping natural-hazard

en: SPOT6 Avalanche outlines 24 January 2018

en: Shapefile of the manually mapped avalanche outlines. Please only use this data together with the example key document provided with this dataset.

format: SHP

en:
Outlines of 18'737 avalanches mapped from SPOT6 satellite data over the Swiss Alps on 24 January 2018. The outlines have different attributes described in the data example key (ExampleKey_AvalMapping.pdf)

The generation of the data is described in:

Bühler, Y., E. D. Hafner, B. Zweifel, M. Zesiger, and H. Heisig (2019), Where are the avalanches? Rapid SPOT6 satellite data acquisition to map an extreme avalanche period over the Swiss Alps, The Cryosphere, 13(12), 3225-3238, doi:10.5194/tc-13-3225-2019.

Abstract.
Accurate and timely information on avalanche occurrence are key for avalanche warning, crisis management and avalanche documentation. Today such information is mainly available at isolated locations provided by observers in the field. The achieved reliability considering accuracy, completeness and reliability of the reported avalanche events is limited. In this study we present the spatial continuous mapping of a large avalanche period in January 2018 covering the majority of the Swiss Alps (12’500 km2).

We tested different satellite sensors available for rapid mapping during a first avalanche period. Based on these experiences, we tasked SPOT6/7 data for data acquisition to cover the second, much larger avalanche period. We manually mapped the outlines of 18’737 individual avalanche events, applying image enhancement techniques to analyze regions in cast shadow as well as brightly illuminated ones. The resulting dataset of mapped avalanche outlines, having a unique completeness and reliability, is evaluated to produce maps of avalanche occurrence and avalanche size. We validated the mapping of the avalanche outlines using photographs acquired from helicopters just after the avalanche period.

This study demonstrates the applicability of optical, very high spatial resolution satellite data to map an exceptional avalanche period with very high completeness, accuracy and reliability over a large region. The generated avalanche data is of great value to validate avalanche bulletins, complete existing avalanche databases and for research applications by enabling meaningful statistics on important avalanche parameters.

Koordinate System: CH1903+ LV95 LN02

avalanche

display_name: avalanche

hazard-mapping

display_name: hazard-mapping

natural-hazard

display_name: natural-hazard

satellite

display_name: satellite


en: spatial-modelling urban-sprawl urban-compactness basic-services forest-persistence topography land-use-and-cover-change forest-gain built-up-classification nature-conservation urban-morphology planning-outcome

en: Descricao dos dados em portiuguês

en: Portugues description

en: Increase in sanitation service

format: GeoTIFF

en: Increase in Normalized Difference Vegetation Index

en: Master plan Ubatuba (zones)

en: Native forest cover persistence from 2005 to 2015

en: Axial

en: New built-up pixels classified as axial

en: Population density per pixel (change per year)

en: Topographic Index Position (TPI)

en: Mean income in Reais (R$) per census sector (change per year)

en:
Basic education in % per census sector (change per
year)

en: Native forest cover gains from 2005 to 2015

en: isolated

en: New built-up pixels classified as isolated

en: slope

en: Slope °

en: Increase in waste collection service

en: Ecological-Economic Zoning (EEZ)

en: Variables description

en: Table of content. Variables description, source, and other important information

en: infill

en: New built-up pixels classified as infill

en: Increase in clean water provision service

en: Master plan Ihabela (zones)

en: Human Development Index (HDI) per municipality (change per year)

en: Permanent housing density increase

en: Urban persistence: Built-up 2005 = Built-up 2015

en:
The present dataset is part of the published scientific paper entitled “The role of spatial planning in land change: An assessment of urban planning and nature conservation efficiency at the southeastern coast of Brazil” (Pierri Daunt, Inostroza and Hersperger, 2021). In this work, we evaluated the conformance of stated spatial planning goals and the outcomes in terms of urban compactness, basic services and housing provision, and nature conservation for different land-use strategies. We evaluate the 2005 Ecological-Economic Zoning (EEZ) and two municipal master plans from 2006 in a coastal region in São Paulo State, Brazil. We used Partial Least Squares Path Modelling (PLS-PM) to explain the relationship between the plan strategies and land-use change ten years after implementation in terms of urban compactness, basic services and housing increase, and nature conservation.

We acquired the data for the explanatory variables from different sources listed on Table 1. Since the model is spatially explicit, all input data were transformed to a 30 m resolution raster. Regarding the evaluated spatial plans, we acquired the zones limits from the São Paulo State Environmental Planning Division (CPLA-SP), Ilhabela and Ubatuba municipality.

1)	Land use and cover data: Urban persistence, Urban axial, Urban infill, Urban Isolates, Forest cover persistence, Forest cover gain, NDVI increase

We acquired two Landsat Collection 1 Higher-Level Surface Reflectance images distributed by the U.S. Geological Survey (USGS), covering the entire study area (paths 76 and 77, row 220, WRS-2 reference system, https://earthexplorer.usgs.gov/). We classified one image acquired by the Landsat 5 Thematic Mapper (TM) sensor on 2005-05-150, and one image from the Landsat 8 Operational Land Imager (OLI) sensor from 2015-08-15. We collected 100 samples for forest cover, 100 samples for built-up cover and 100 samples for other classes. We then classified these three classes of land cover at each image date using the Support Vector Machine (SVM) supervised algorithm (Hsu et al., 2003), using ENVI 5.0 software.

Land-use and land-cover changes from 2005 to 2015 were quantified using map algebra, by mathematically adding them together in pairs (10*LULC2015 + LULC2005). We reclassified the LULC data into forest gain (conversion of any 2005 LULC to forest cover in 2015); forest persistence (2005 forested pixels that remained forested in 2015); new built-up area (conversion of any 2005 LULC to built-up in 2015); and urban maintenance (2005 built-up pixels that remained built-up in 2015).

To describe the spatial configuration of the urban expansion, we classified the new built-up areas into axial, infill and isolated, following Inostroza et al. (2013) (For details, please refer to Supplementary Material I at the original publication).

The NDVI was obtained from the same source used for the LULC data. With the Google Engine platform, we used an annual average for the best pixels (without clouds) for 2005 and 2015, and we calculated the changes between dates. We used increases of > 0.2 NDVI to represent an improvement in forest quality.

2)	Federal Census data organization: Urban Basic Services and Housing indicator, socioeconomic and population:

The data used to infer the values of basic services provision, socioeconomic and population drivers was derived from the Brazilian National Census data (IBGE, 2000 and 2010). Population density, permanent housing unit density, mean income, basic education, and the percentage of houses receiving waste collection, sanitation and water provision services, called basic services in the context of this study, were calculated per 30 m pixel. The Human Development Index is only available at the municipality level. We attributed the HDI for the vector file with the municipality border, and we rasterized (30 m resolution) this file in QGIS. Annual rates of change were then calculated to allow comparability between LULC periods. To infer the BSH, we used only areas with an increase in permanent housing density and basic services provision (See Supplementary Material I at the original publication).

3)	Topographic drivers

To infer the values of the topographic driver, we used the slope data and the Topographic Index Position (TPI) based on the digital elevation model from SRTM (30 m resolution) produced by ALOS (freely available at eorc.jaxa.jp/ALOS/en/about/about_index.htm), and both variables were considered constant from 2005 to 2015 (See Supplementary Material I at the original publication).

basic-services

display_name: basic-services

built-up-classification

display_name: built-up-classification

forest-gain

display_name: forest-gain

forest-persistence

display_name: forest-persistence

land-use-and-cover-change

display_name: land-use-and-cover-change

nature-conservation

display_name: nature-conservation

planning-outcome

display_name: planning-outcome

spatial-modelling

display_name: spatial-modelling

topography

display_name: topography

urban-compactness

display_name: urban-compactness

urban-morphology

display_name: urban-morphology

en: Spatially explicit data to evaluate spatial planning outcomes in a coastal region in São Paulo State, Brazil


en: precipitation temperature meteorology swiss-forest-lab climate-change long-term meteo par wind-speed relative-humidity

en: Data plot of the forest station (LEB)

en: Data overview for air temperature, relative humidity, precipitation, PAR, wind speed.

en: Site photo of the forest station (LEB)

en: Site photo of the forest station from below (viewing upwards the slope)

mimetype: image/jpeg

en: Forest station data (LEB)

en: Data file.

mimetype: text/csv

en: High quality meteorological data are needed for long-term forest ecosystem research, particularly in the light of global change. The long-term data series published here comprises almost 20 years of measurements for one meteorological station in Lens in Switzerland which is located within a natural coniferous forest with Scots pine (_Pinus sylvestris_; 150-170 yrs)) as dominant tree species. The meteorological time series are presented in hourly time resolution of air temperature, relative humidity, precipitation, photosynthetically active radiation (PAR) and wind speed. Lens is part of the Long-term Forest Ecosystem Research Programme (LWF) established and maintained by the Swiss Federal Research Institute WSL.

climate-change

display_name: climate-change

long-term

display_name: long-term

meteo

display_name: meteo

meteorology

display_name: meteorology

par

display_name: par

precipitation

display_name: precipitation

relative-humidity

display_name: relative-humidity

swiss-forest-lab

display_name: swiss-forest-lab

temperature

display_name: temperature

wind-speed

display_name: wind-speed

educ

en: Education, culture and sport

envidat

en: EnviDat: the Environmental Data Portal

en: EnviDat is the WSL data portal providing unified and managed access to environmental monitoring and research data. The portal has the capability to host and publish data sets. Through the sharing of unique and high-value data sets worldwide, EnviDat fosters research and contributes to advancing environmental science.

en: Lens, Switzerland: Long-term forest meteorological data from the Long-term Forest Ecosystem Research Programme (LWF), from 1997 onwards


en: lad-use-chages bombus-pasquorum nutrient-intake foraging-behaviour zurich bombus-lapidarius pollen-metabarcoding dietary-patterns basel macronutrients bumblebees rural bern urban bees

en:
The dataset contains the fatty acid content and ratios for the two bumblebees. Measures are taken only from pollen from the leg-baskets. SampleID is not the same as in the metabarcoding, several samples from different bumblebees were merged within a Location ,Landscape and Replica. Not for all the samples there is information on both amino acids and fatty acids. The columns are:
- SampleID_chemical: The ID for chemical analyses
- Location: the three Swiss cantons studied. Levels: Bern =BE; Basel = BS; Zurich =ZH
- Landscape: the two typea of human-dominated ecosystems, nested to the Swiss canton. Levels: Urban = U; Rural = R
- Replicate: sampling place (800-m buffer) nested with the location and the landscape. Levels: A-E.
- Bumblebee_species: the two studied species, levels: B.pasquorum; B. lapidarius
- LocationLandscape: combination between location and landscape
- Caprylic, Pelargonic, ..., Lacceroic: Content of individual fatty acids acids.
- sum: total sum of fatty acid content (mg)
- unsaturatedsum: total sum unsaturated fatty acids (mg)
- saturatedsum: total sum saturated fatty acids (mg)
- omega3sum: total sum Omega 3 fatty acids (mg)
- omega6sum: total sum Omega 6 fatty acids (mg)
- omega9sum: total sum Omega 9 fatty acids (mg)
- omega6to3ratio: ratio Omega 6 to Omega3 fatty acids
-saturatedtounsaturatedration: ratio between saturated and unsaturated fatty acids

en:
Processed data. The dataset contains the plant species richness in the leg-baskets per bumblebee individual. It contains:
- SampleID: Combining bumblebee ID, location, landscape and replica
- Location: canton, levels: Bern =BE; Basel = BS; Zurich =ZH
- Landscape: landscape type, levels: Urban = U; Rural = R
- Replicate: sampling place (800-m buffer) within location and landscape. Levels: A-E.
- LocationLandscape: combining location and landscape
- Bumblebee_species: the two studied species, levels: B.pasquorum; B. lapidarius
- Plant species richness: the number of plant species found in the pollen of the leg-baskets.

en:
Processed data. The dataset contains the phylogeneitc diversity metrics based on the plant composition from the leg-baskets per bumblebee individual. It contains:
- SampleID: Combining bumblebee ID, location, landscape and replica
- Location: canton, levels: Bern =BE; Basel = BS; Zurich =ZH
- Landscape: landscape type, levels: Urban = U; Rural = R
- Replicate: sampling place (800-m buffer) within location and landscape. Levels: A-E.
- LocationLandscape: combining location and landscape
- Bumblebee_species: the two studied species, levels: B.pasquorum; B. lapidarius
- PVar: phylogenetic variance
- PRic: Phylogenetic richness
- PEve: Phylogenetic evenness
- PClu: Phylogenetic clustering

en:
Processed data. The dataset contains the functional diversity metrics based on the plant composition from the leg-baskets per bumblebee individual. It contains:
- SampleID: Combining bumblebee ID, location, landscape and replica
- Location: canton, levels: Bern =BE; Basel = BS; Zurich =ZH
- Landscape: landscape type, levels: Urban = U; Rural = R
- Replicate: sampling place (800-m buffer) within location and landscape. Levels: A-E.
- LocationLandscape: combining location and landscape
- Bumblebee_species: the two studied species, levels: B.pasquorum; B. lapidarius
- Fric.w: Weighted functional richness
-Fric: functional richness
-FEve.w: Weighted functional evenness
- FEve: functional evenness
- FDiv.w: weighted functional divergence
- FDiv: functional divergence

en:
The dataset contains the plant trait values obtined from published sources. It contains:
- Kingddom: taxonomic
- Phylum: taxonomic
- Order: taxonomic
- Family: taxonomic
- Genus: taxonomic
- Species: species name
- plant.species: full scientific name
- native_exotic: origin status. As presented in https://www.doi.org/10.16904/envidat.210
- pollination mode: vector of pollination. As presented in https://www.doi.org/10.16904/envidat.210
- Flowering_months_duration: Number of flowering months. As presented in https://www.doi.org/10.16904/envidat.210
- start_flowering: month of the starting of the flowering. As presented in https://www.doi.org/10.16904/envidat.210
- growth_form_category: plant growth form. As presented in https://www.doi.org/10.16904/envidat.210
- plant-height: plant heght in meters. As presented in https://www.doi.org/10.16904/envidat.210
- inflorescence: Logic, plant with single flowers (0) or inflorescences (1). As presented in https://www.doi.org/10.16904/envidat.210
- structural_blossom_class: depicting the accessibility of the flowers. As presented in https://www.doi.org/10.16904/envidat.210
- symmetry: floral symmetry. As presented in https://www.doi.org/10.16904/envidat.210
- nectar: logic, nectar present. As presented in https://www.doi.org/10.16904/envidat.210
- pollen: logic, pollen rewards present. As presented in https://www.doi.org/10.16904/envidat.210
- oil: logic. oil present. As presented in https://www.doi.org/10.16904/envidat.210
- sugar.concentration: the amount of sugar present in the nectar, in mg.
Additional information can be found in https://doi.org/10.1016/j.dib.2021.107243

en:
The dataset contains the information on the 16 study sites:
- Location: the three Swiss cantons studied. Levels: Bern =BE; Basel = BS; Zurich =ZH
- Landscape: the two typea of human-dominated ecosystems, nested to the Swiss canton. Levels: Urban = U; Rural = R
- Replicate: sampling place (800-m buffer) nested with the location and the landscape. Levels: A-E.
- Site_ID: combination of location, landscape and replicate
- X: X coordinate, WGS84
- Y: Y coordinate WGS84
- Plant S in landscape: Plant species richness within the 800 m calculated using both information from the Global Biodiversity Information. Facility (GBIF) and InfoFlora (www.infoflora.ch).
- % Buildings: the proportion of buildings and other impervious surfaces within 800 m radius.
- % Agricultural: the proportion of agricultural land and other impervious surfaces within 800 m radius.
- % Water: the proportion of water and other impervious surfaces within 800 m radius.
- % Meadows & grasslands: the proportion of meadows and grasslands and other impervious surfaces within 800 m radius.
The raw metabarcoding data is archived in NCBI project PRJNA1137320.

en:
The dataset contains the amino acid content and ratios for the two bumblebees. Measures are taken only from pollen from the leg-baskets. SampleID is not the same as in the metabarcoding, several samples from different bumblebees were merged within a Location ,Landscape and Replica. Not for all the samples there is information on both amino acids and fatty acids. The columns are:
- SampleID_chemical: The ID for chemical analyses
- Location: the three Swiss cantons studied. Levels: Bern =BE; Basel = BS; Zurich =ZH
- Landscape: the two typea of human-dominated ecosystems, nested to the Swiss canton. Levels: Urban = U; Rural = R
- Replicate: sampling place (800-m buffer) nested with the location and the landscape. Levels: A-E.
- Bumblebee_species: the two studied species, levels: B.pasquorum; B. lapidarius
- LocationLandscape: Combining location and landscape
- Asp, Thr, ..., Arg: Content of individual amino acids. Amino acids are written as abbreviated names. FUll names be checked here: https://en.wikipedia.org/wiki/Amino_acid
- sum: total sum of amino acid content (mg)
- sumessential: total sum essential amino acids (mg)
-sumnon-essential: total sum non-essential amino acids (mg)
- proportionnonessentialessential: proportion between essential and non-essential amino acids.

en:
The dataset contains the filtered plant composition1 (removing species with too low relative abundances) and the relative abundance obtained from DNA metabarcoding on pollen samples for both the leg-baskets and the body. The dataset contains the following columns:
- SampleID: Combining bumblebee ID, location, landscape and replica
- Abundance: numeric, relative abundance
- BumblebeeID: numerical ID for each bumblebee individual within a location, landscape and replicate sampling place.
- Location: canton, levels: Bern =BE; Basel = BS; Zurich =ZH
- Landscape: landscape type, levels: Urban = U; Rural = R
- Replicate: sampling place (800-m buffer) within location and landscape. Levels: A-E.
- LocationLandscape:
- Bumblebee_species: the two studied species, levels: B.pasquorum; B. lapidarius
- Transportation_structure: bumblebee pollen transportation structure, levels: B = Body; L = leg-baskets (i.e. corbicula)
- Kingddom: taxonomic
- Phylum: taxonomic
- Order: taxonomic
- Family: taxonomic
- Genus: taxonomic
- Species: plant sicentific name
-Binomial_abundance: Logic, indicating if the plant species is included (1).
The raw metabarcoding data is archived in NCBI project PRJNA1137320

en:
Data on the diet of urban and rural bumblebees individuals, Bombus lapidarius and Bombus pascuorum, collected in Switzerland (cantons Bern, Basel and Zürich) obtained using metabarconding and chemical analyses from two pollen transportation structures, that is, the body and the leg-baskets (i.e., corbicula). The bumblebees were collected by Egenberger et al., 2019 (https://doi.org/10.5061/dryad.qt8mr4v)
The data contains:
- The composition and relartive abundance of plant species in the body and the leg-baskets, separately.
- The content and ratios of two groups of macronutrients, that is, amino acids and fatty acids.
The dataset contains the data used in the paper "Urban bumblebees diversify their foraging strategy to maintain nutrient intake" as well as unpublished data.

basel

display_name: basel

bees

display_name: bees

bern

display_name: bern

bombus-lapidarius

display_name: bombus-lapidarius

bombus-pasquorum

display_name: bombus-pasquorum

bumblebees

display_name: bumblebees

dietary-patterns

display_name: dietary-patterns

foraging-behaviour

display_name: foraging-behaviour

lad-use-chages

display_name: lad-use-chages

macronutrients

display_name: macronutrients

nutrient-intake

display_name: nutrient-intake

pollen-metabarcoding

display_name: pollen-metabarcoding

rural

display_name: rural

urban

display_name: urban

zurich

display_name: zurich